Changing channel settings
LHD32V77MH
13
Adjusting the Features
To change the channel settings:
In TV mode, you can adjust:
1 Press MENU. The Main menu opens.
2 Press or to highlight Features, then press ENTER or . The
TV menu opens.
Features TV
Caption settings >>>
Sleeptimer 0
Power on >>>
Power off >>>
V-Chip >>>
Change PIN >>>
Transpaerncy 0
OSD Timeout >>>
Move:
3
Press or to highlight an option, then press or to access
Enter: OK
the option, and press or to adjust
Caption settings– Adjust Captioning settings.
Sleeptimer –Press [ / ] to set the sleep timer between
0-120minutes.
Power on –When “On”, you can set the time when the TV turns
on automatically. And Set the current time when the TV turns on.
Power off –When “On”, you can set the time when the TV turns
off automatically. And set the current time when the TV turns off.
V-Chip –Lock channels in Channel Manager, to prevent
unauthorized users, such aschildren, from watching unsuitable
programme. Available only when the Input source is set to TV.
Hotel Function Lock TV
Function V-Chip TV
Off
US TV Parental Guid... >>>
Search Lock Off
US MPAA Rating
User Save Lock Off
Canadian English Rating Select
Picture Lock Off
Canadian French Rating Select
Audio Lock Off
Features Lock Off
Installation Lock Off
DMP Lock Off
Move:
Move:
.
.
.
.
.
.
.
Enter: OK
Enter: OK
Access to V-Chip Menu
Press the number buttons to enter the four-digit password. The
default password is 0532.
Press or to highlight an option, then press or to access
the option. Press or to highlight a rating and press to
lock the rating and all other higher ratings or unlock the rating and
Program Block–
A–Rating Enable is on.
B–U.S. TV Ratings: You can choose TV ratings according
to the illustration on the screen.
C–The settings for U.S. Movie Ratings, Canada (English)
Ratings, and Canada (French) Ratings follow Step B. If
you want to block an unrated program, turn on this
function. You can select all the ratings listed in the
charts below.
Exit: EXIT
ENTER
the option. You can select:
.
Select
.
.
.
.
.
.
Exit: EXIT
Exit: EXIT
The V-Chip menu opens.
ENTER
ENTER
U.S. TV ratings (age-based)
These ratings are determined by the Federal
Communications Commission (FCC).
TV-Y All children.
TV-Y7 Suitable for children 7 and older.
TV-G General audiences.
TV-PG Parental guidance suggested.
TV-14 Parental guidance strongly suggested.
TV-MA Mature audiences only.
U. S. TV ratings (content-based)
FV Fantasy violence.
V Violence.
S Sexual situations.
L Strong language.
D Suggestive dialog.
U.S. movie (MPAA) ratings
These ratings are determined by the Motion Picture
Association of America (MPAA).
G General audiences.
PG Parental g
PG-13 Suitable for children 13 and ol
uidance suggested.
der.
R Parental guidance suggested for children
under 17.
NC-17 Not suitable for children under 17.
X Adults only.
Canadian English ratings
These ratings are based on the Canadian Home Video
Rating System, determined by the Canadian Motion
Picture Distributors Association (CMPDA).
C Suitable for all children.
C8+ Suitable for children 8 and older.
G General audiences.
PG Parental guidance suggested.
14+ Suitable for children 14 and older.
18+ Adults only.
Canadian French ratings
determined by La Régle du cinéma du Québec.
G General audiences.
8 ans+ Suitable for children 8 and older.
13 ans+ Suitable for children 13 and older.
16 ans+ Suitable for children 16 and older.
18 ans+ Adults only.
Change PIN–Change the password of the V-Chip function.
Transpaerncy–Adjust the transparency of menu.
OSD Timeout –The time it takes the OSD to disappear when
no operations are performed. You can change it from Off, 5
seconds, 10seconds, and 30seconds.
14
Changing channel settings
LHD32V77MH
Adjusting the Installation
To change the channel settings:
In TV mode, you can adjust:
1 Press MENU. The Main menu opens.
2 Press or to highlight Installation, then press ENTER
or . The
Installation TV
TV menu opens.
Language English
Channels >>>
Time >>>
Source Labels >>>
Reset AV settings Start now
Move:
3
Press or to highlight an option, then press or to access
Enter: OK
the option, and press or to adjust
Exit: EXIT
ENTER
the option. You can select:
Language –You can select the menu's language among
English, French and Spanish.
Channels –You can select the mode of RF input and
search the channels automatically.
Installation Channels TV
Autoprogram
Installation mode Antenna
Move:
Enter: OK
Start now
.
.
.
.
.
.
.
Exit: EXIT
Time– Lets you set the exact time. You can setup
date,time,time zone and daylight saving.
Source Labels–Lets you name each input.
Reset AV settings –Change setting back to default.
(picture and sound only)
Troubleshooting
Troubleshooting
LHD32V77MH
15
Before calling for service, check the following information for possible
solutions to problems you may experience. If none of these solutions
Caution: Do not try to repair the TV yourself. Refer all servicing to
Video and audio
Problem Solution
No picture (screen is not lit)
and no sound.
Dark, poor, or no picture
(screen is lit), but sound is
good.
No color, dark picture, or
color is not correct.
Only snow (noise) appears
on the screen.
Dotted lines or stripes
appear on the screen.
Double images.
Problem Solution
The picture has a few bright
or dark spots.
Good picture, but no
sound.
Audio noise.
Make sure that the power cord is
plugged in.
Press POWER on the TV or the
remote control.
Make sure that the correct video
input source is selected. For more
information, see “Selecting the
video input source” on page 9.
Try another channel. The station
may be experiencing problems.
Adjust the brightness. For more
information, see “To adjust the
picture:” on page 12.
Make sure that the correct picture
mode is selected.
information, see “To adjust the
picture:” on page 12.
Make sure that the antenna or
cable TV is connected correctly
and securely. For more
information, see “Connecting an
antenna, cable TV, or satellite TV
box” on page 8.
Adjust the color saturation. For
more information, see “Adjusting
the picture” on page 12.
Try another channel. The station
may be experiencing problems.
Make sure that the antenna or
cable TV is connected correctly
and securely. For more
information, see “Connecting an
antenna, cable TV, or satellite TV
bo
x” on page 8.
Adjust the antenna.
Move the TV away from noise
sources such as cars, neon signs,
or hair dryers.
Try using a highly directional
outdoor antenna or cable TV.
A few bright or dark spots on an
LCD screen is normal. It does not
Make sure that the sound is not
muted.
Make sure that the sound mode is
set to Stereo or Mono. For more
information, see “Selecting the
audio mode” on page 12.
Make sure that there is no
interference with infrared
equipment such as a cordless
telephone or headphones. Move
the infrared equipment away
from the TV to eliminate the
noise.
For more
Remote control
Problem Solution
Remote control does not
work.
Trouble programming your
existing universal remote
control.
General
Problem Solution
One or more channels do
not display.
Password is lost.
Some settings cannot be
accessed.
TV cabinet creaks.
Co
ntrol buttons on the TV
do not work.
Note: If the problem is not solved by using these troubleshooting
Make sure that the TV power cord
is plugged in.
Make sure that there are no
obstructions between the remote
control and the remote control
sensor on the front of the TV.
Make sure that the batteries are
installed correctly. For more
information, see “Installing
remote control batteries” on
page 6.
Replace the batteries. For more
information, see “Installing
remote control batteries” on
page 6.
See instructions and a table of
common codes in “Programming
a universal remote control to
work with your
Codes are subject to change. For
up to date codes, go to
www.dynexproducts.com.
Replace the batteries. For more
information, see “Installing
remote control batteries” on
page 6.
Refer to the User Guide that
accompanied your universal
remote control and contact the
manufacturer if problems persist.
Make sure that the channels are
not blocked. For more
information, see “Setting parental
controls” on page 13.
Enter 0532 to access parental
controls, then set a new
password. For more information,
see “Setting parental controls” on
page 13.
If a setting is grayed, the setting is
not available in the current video
input mode.
When the TV is in use, the
temperature rises naturally and
may cause the cabinet to expand
or contract which can cause a
creaking noise. This is not a
malfunction.
Disconnect the power cord, wait a
few seconds, then reconnect the
power cord and turn on the TV.
TV” on page 7.
16
LHD32V77MH
Specifications, Legal notices
Maintenance
Just like with any other household appliance, the performance and
life-expectancy of your TV depends on how well you maintain it. Follow
the procedures described here to clean the TV case and the LCD screen.
Cautions:
disconnected from the power outlet before cleaning the TV.
Never spray or pour any liquid directly onto the screen or the case.
Cleaning
Clean your TV with a soft, dry cloth. If surfaces are extremely
dirty, use a soft cloth dampened with a small amount of
non-ammonia, non-alcohol-based, non-abrasive detergent
solution.
Clean the screen with a clean, soft, lint-free cloth. If additional
cleaning is necessary, apply a small amount of non-ammonia,
non-alcohol-based, non-abrasive detergent solution to the cloth.
Weight and dimensions shown are approximate.
Legal notices
FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation of this
product is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply within the limits
for a class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
that to which the receiver is connected.
Consult the dealer or an experienced technician for help.
FCC warning
TV type
TV panel
TV system
Receiving channels
Audio multiples
Audio out
Power requirement
Power consumption
Dimensions
(W × H × D with stand)
Weight
Input terminals
Output terminals
Control terminals
LCD
31.5-inch TFT LCD
NTSC-M, ATSC
VHF: 2 - 13
UHF: 14 - 69
CATV: 1 - 125
CADTV: 1-135
DTV: 2-69
BTSC system
6 W x 2
AC 120 V, 60 Hz
140 W (With Max backlight)
31.17 × 22.08 × 9.05 inches
(792 × 561 × 252 mm)
26.9 lbs. (12.2 kg)
Composite video/L and R audio (1)
Component video/L and R audio (2)
HDMI (3)
VGA/audio (1)
ANT/Cable In (1) USB(1)
Digital Coaxial Audio (1)
Headphone (1)
SERVICE PORT (2)
responsible for compliance with the FCC Rules could void the user’s
authority to operate this equipment.
Cables
Connections to this device must be made with shielded cables with
metallic RF/EMI connector hoods to maintain
compliance with FCC
Rules and Regulations.
Canada ICES-003 statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe B est conforme a la norme NMB-003
du Canada.
Standard Television Receiving Apparatus — Appareil de réception
télévision ordinaire, Canada BETS-7 / NTMR-7
HDMI
trademarks or registered trademarks of HDMI Licensing LCC.
Hotel Settings
Adjusting hotel settings
LHDN32V88MH
17
To adjust hotel settings:
1 Press MENU. The Main menu opens.
2 Press or to highlight SOUND, then press ENTER or , audio
menu opens. Press or to highlight balance, use or to
adjust to zero, then press the number buttons to enter the three digit password 5 4 8. The Hotel Settings Menu opens.
Sound TV
Sound mode Standard
Equalizer >>>
Balance
Balance
Move:
Enter: OK
0
Exit: EXIT
0
Note: Please redo above step if fail when opening Hotel Settings Menu.
3
Press or to highlight an option, then press or to access
the option, press or to select a value and press to adjust
ENTER
ENTER
the option. You can select:
HOTEL MODE —Allows installer to active or disable hotel options.
On
: Hotel options are active.
: Hotel options are disabled.
TV ON SETTING —Allows installer to set up of initial options each
time a guest turns TV on.
Hotel TV On Setting TV
On Volume Off
On Source Last
Logo HISENSE
Power On Standby
Basic Seetting Off
Move:
.
.
.
.
.
.
.
Enter: OK
Exit: EXIT
On Volume
In ON mode, can be adjusted from 0 to 100.ON VOLUME VALUE
On Source
Input options. Choises include antenna ( )
)
( ypbpr1, ypbpr2 , HDMI1,HDMI2,HDMI3,
will remember previous input source.
LAST
TV ON CHANNEL ON
on source will activate selection and
TV , AV,
and
VGA.
VGA.
CHANNEL NUMBER.
On Channel Number
—Allows installer to set up desired
channel when TV is turned on. If no desired channel is requested
ON CHANNEL
component
—Allows installer to choose one of three options. Choices
LOGO
are and .
OFF, HISENSE WELCOME
: No logo when TV is turned on. TV goes directly to source.
OFF
HISENSE
WELCame
Power On
Choices are and
LAST
: Displays Hisense TV logo.
: Displays welcome logo.
—Allows installer to select one of three options.
LAST, ON Standby.
: TV will return to whatere operation it was in before power
out.
: TV will turn on when power is restored.
ON
Standby
Basic Setting
ON
: TV will be activated but not turned on.
—Allows installer to active or disable basic settings.
: TV picture defaults to Normal viewing mode, Normal Audio
and Zoom Aspect is full screen.
: Installer can go to and adjust settings.
OFF
User Save Lock
FUNCTION Lock —Allows installer to lock the following functions.
Hotel Function Lock TV
Hotel Function Lock TV
Off
KB Lock Off
Search Lock Off
Search Lock Off
User Save Lock Off
User Save Lock Off
Picture Lock Off
Picture Lock Off
Audio Lock Off
Audio Lock Off
Features Lock Off
Features Lock Off
Installation Lock Off
Installation Lock Off
DMP Lock Off
DMP Lock Off
Move:
Move:
—Locks key pad.
kB lock
: Usable.
OFF
: Locked down (disabled).
ON
Search Lock
OFF
ON
User Save Lock
OFF
—Locks key pad.
: Usable.
: Locked down (disabled).
—Locks hotel guest adjustment.
: Menu features can be adjusted by hotel guest and be
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Enter: OK
Enter: OK
Exit: EXIT
Exit: EXIT
remembered in TV memory.
ON
factory default settings.
—Locks Picture adjustments in menu.Picture Lock
: Picture adjustments in menu are allowed by user.
OFF
: Locks all picture adjustments.
ON
Audio Lock
OFF
ON
—Locks Audio adjustments in menu.
: Audio adjustments in menu are allowed by user.
: Locks all audio adjustments except Balance.
18
LHDN32V88MH
Hotel Settings
Feature Lock
Installation Lock
DMP Lock
—Locks Feature menu adjustment in menu.
—Locks Installation menu adjustment in menu.
—Locks DMP menu adjustment in menu.
V-Chip—Locks V-Chip function in menu.
Info Lock
: Programing name and description (if available) are
OFF
displayed when info button on remote is touched. Programing
info may also be available depending on provider.
: No detail information on channel.
ON
Hotel mute—
ON
: TV is muted. User can not adjust volume.
OFF
: TV is not muted. User can adjust volume.
Allows installer to mute TV speaker.
Input Selection
: Locked down (disabled).
OFF
: Usable.
ON
MAX VOLUME —Allows installer to adjust max volume from 0 to 100.
The volume value can be input by digit-number buttons on remote.
MIN VOLUME —Allows installer to adjust minimum volume from 0 to 100.
The volume value can be input by digit-number buttons on remote.
AUTO Standby
: TV will stay on with no signal.OFF
: TV goes to Standby mode when there is no signal after 15 mimutes.ON
CHANNEL SETTINGS —Allows access to channel setting without exiting
hotel settings menu.
—
In channel setting mode, Allows edit and Program Guide Edit
remapping and editing of channels available. Using the color keys
installer can change channel position and name.
CLONING OPTION 2.
A---
Take loaded USB drive to next unit, plug in next installation
unit (You do not need to have sources connected).
B---
Plug in loaded USB drive.
C---
Turn TV on.
D---
Go to Menu.
E---
Go to Audio menu.
F---
Go to Balance. Use arrows to adjust to zero.
G---
Enter access code 548 with remote number key. Hotel menu
opens.
H---
Go to clone near bottom.
J---
Choose option Write In. Hit Enter on remote. Cloning option
will appear on screen.
k---
Select Yes. System will acknowledge download success. TV
will be cloned.
SSID setting
—Set or reset SSID code for Pro:Idiom decording.
Set SSID
Reset SSID
SW Version
—Enter new SSID code.
—Reset SSID code to factory default value.
yes
: Reset to factory default code.
No
: Maintain current settings.
—shows current software version information.
Hotel Channel Setting TV
Digital Page2/1
NO# Name PHY. Program Skip
1
2
3
4
5
6
7
8
9
10
Rename: Skip: Copy: Delete: Swap:
Select:
Enter: OK
23 5-1
23 5-2
23 5-3
23 5-4
17 17
29 29
45 45
57 57
69 69-1
69 69-2
CLONE
(copy) settings to any additional units you are installing.
First plug in USB driver to unit that is already set up. (TV will showA---
USB found).
Select READ OUT which brings up cloning function.B---
Select YES to clone (copy). When complete, TV will show uploadC---
success. Hotel Menu will close automatically.
CLONING OPTION 1.
A---
Plug in new TV.
B---
Plug in loaded USB drive.
C---
Turn TV on.
D---
On screen will acknowledge USB detected.
E---
Press menu.
F---
Key in numbers 2 5 6 6 3 on remote.
G---
Cloning option will appear on screen.
Exit: EXIT
Loading...