Hisense 100L9G-D12 User guide

USER MANUAL

Read the manual carefully and ensure you have fully understood its contents before operating this device for the first time.

English

▌Important Notice

Paragraphs beginning with the symbol indicate important instructions, tips or conditions for the following settings.

For your own safety and the optimal performance of your device, ensure to read the safety instructions before performing any

installation.

Compatibility with 3rd party products, software and services are not guaranteed. We cannot be held liable for any damage or loss
suffered whilst operating, using or connecting to incompatible devices or apps.

The recording and playback of content on this or any other device may require permission from the owner of the copyright or other
such rights in that content. It is your responsibility to ensure that your use of this or any other device complies with applicable
copyright legislation in your country. Please refer to that legislation for more information on the relevant laws and regulations involved
or contact the owner of the rights of the content you wish to record or playback.

Read these instructions
Follow all instructions
Heed all warnings
Keep these instructions
All rights reserved.

▌Safety Instructions

To ensure safe and correct use of this product, always comply with the following precautions to avoid dangerous situations and
damage to your unit:

The lightning flash with arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.

A

The intended use and ambient conditions for this device

This device is intended for the rendering of video and audio signals, on a table-top, in a home or ofce environment. It must not be

used in rooms with a high level of humidity or dust concentration. The warranty is only valid if used as intended by the manufacturer.

WARNING

High humidity and dust concentration may lead to current leaks in the device. To reduce the risk of re or electrical shock:

- Do not expose this unit to rain, moisture, dripping or splashing water, and do not place objects lled with liquids, such as vases,

cups, etc. on or over the unit.

- Do not touch the device with wet hands.

- Do not expose to direct air-conditioning and keep candles or other naked ames away from the device at all times.

If the device is moved from a cold environment to a hot environment, leave it switched off for at least an hour to avoid condensation.
If used outside, make sure it is protected from moisture.

If you notice anything unusual, immediately remove the power plug.

In case of re, use preferably a CO2 gas or powder re extinguisher. If such extinguishers are not accessible, try to isolate the electrical
supply before using a water re extinguisher.

Never place a television set in an unstable location. A television set may fall, causing serious personal injury or death. Many injuries,
particularly to children, can be avoided by taking simple precautions such as:

- Using cabinets or stands recommended by the manufacturer of the television set.

- Only using furniture that can safely support the television set.

- Ensuring the television set is not overhanging the edge of the supporting furniture.

- Not placing the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and
television set to a suitable support.

- Not placing the television set on cloth or other materials that may be located between the television set and supporting furniture.

- Educating children about the dangers of climbing on furniture to reach the television set or its controls.

If your existing television set is being retained and relocated, the same considerations as above should be applied.

B

Power Supply

Power plug and power cable

Incorrect voltages can damage the device. Only connect this unit

to a power supply with the correct voltage and frequency noted
on the type plate, using the supplied power cable.

The power plug must be easily accessible so that the device can
be disconnected at all time. The unit is live, even if in standby
mode, as long as the unit is connected to a power outlet.

It is recommended that this unit is placed on a dedicated circuit.

- Do not overload the power outlets by connect too many

appliances to the same outlet. Overloaded wall outlets,

extension cords, etc. are dangerous and can result in electric

shock and re.

After power off, don't turn it on again in 5 seconds. Frequent
switching power supply in a short period of time can cause
abnormal device.

- Do not touch the power plug with wet hands.

- Do not place heavy objects on the power cable. Route the
cable so that it is not kinked or laid over sharp edges, walked
on or exposed to chemicals. A power cable with damaged

insulation can cause electric shock and re.

- Pull the power plug, NOT on the cable when disconnecting.

The cable can become damaged and cause a short circuit if
pulled on.

- Do not place the power cable near a high temperature object.

- Do not move the device with the power cable plugged into a
socket.

- Do not use a damaged or loose power cable, or a damaged
socket outlet.

- Do not use any power cords other than the one supplied with
this unit.

Air ventilation and high temperatures

Install your device only where there is proper ventilation, and ensure
that there is at least 20 cm free space on the sides and 15 cm
free space on the back unit for air circulation. Excessive heat and

obstruction of ventilation could lead to re or early failure of some

electric components.

- Do not block any ventilation openings with newspapers,
tablecloths, curtains, etc.

- Do not dry clothing etc. on top of the unit.

- Take care not to touch the ventilation openings since they may

C

become hot.

- Do not insert foreign objects into the device through the vents.

Warning about off-gassing

New furniture, carpet, paint, building materials and electronics
can release chemicals into the air through evaporation. After

you set your device up and turn it on for the rst time, you may

notice a slight smell within a couple of hours. This is because

some components of device are heating up for the rst time. The

materials that we use fully meet the environmental requirements

and regulations. Your device is working just ne and the fumes

from the off-gassing will diminish eventually.

Thunder Storms

Pull out the power plug and all connected antenna cables from

the device during a thunderstorm. Overvoltage caused by

lightning strikes can damage the device via the antenna system,
as well as the wall socket.

Long periods of absence

As long as the power plug is connected to a live socket outlet,
the device will consume power even in standby mode. The power
plug and all connected antenna cables should be disconnected
out during long periods of absence.

Supervision

- Do not let children play unsupervised close to the device. It
could tip over, be pushed off or pulled down from the stand
surface and injure someone.

- Do not allow a switched-on device to run unattended.

Volume

Loud music and noises can lead to irreversible damage to your
ears. Avoid extreme volume, especially over long periods and
when using headphones.

If you hear a drumming noise in your ears, turn down the volume
or temporarily stop using headphones.

Cleaning and care

CAUTION:

Unplug the power cord prior to cleaning the device.
Clean the device, the screen, and the remote control with a

soft, moist, clean and color-natural cloth only. Do not use any
chemicals.

- Do not subject the surfaces to insect repellent, solvent,
thinner or other volatile substances. This may degrade the
surface quality.

- Do not spray water or other liquids directly on the device.
Liquid inside the device could lead to product failure.

- The surface of the display panel is treated and may be easily

damaged. Take care not to scratch it with ngernails or other

hard objects.

D

- Also wipe the power plug with a dry cloth at regular intervals.

Service/Repair

Never remove the cover/back of the device; there are no user

serviceable parts inside. Refer all service to qualied service

personnel.

Packaging

Keep the anti-moisture materials and plastic bags out of reach of
children.

Plastic bags can cause suffocation and the anti-moisture material
is harmful if swallowed. If swallowed by mistake, force the patient
to vomit and visit the nearest hospital.

- Do no use rechargeable batteries.

- Do not burn or break up batteries.

- Be sure to dispose of batteries correctly.

- Do not expose batteries to excessive heat such as sunshine,

re or the like.

Outdoor Antenna Grounding

If an outdoor antenna used, be sure the antenna system is
protected against voltage surges and built-up static charges.

Disposal

Refer to the recycling section of this manual.

Modication

Do not attempt to modify this product in any way. Unauthorized

modication could void the warranty of this unit, cause electric
shock and res.

Remote Control batteries

- Incorrect installation may cause battery leakage, corrosion
and explosion.

- Replace only with the same or equivalent type.

- Do not mix old and new batteries.

- Do not mix different battery types.

Laser

Do not look directly at the lens when this device is on
because the laser light may damage your eyes!

- This product comes with a laser module. Do not tear or
modify this device in any manner; otherwise, it may result in
personal injury.

RG2

As with any bright light source, DO NOT STARE INTO THE

BEAM IEC 62471-5: 2015

CLASS 1 LASER PRODUCT

λ = 459~471nm/519~531nm/635~651nm

Wavelength 459~471nm/519~531nm/635~651nm

CLASS 1 LASER PRODUCT IEC 60825-1: 2014

E

CAUTION:

Use of controls or adjustments or performance of procedures

other than those specied herein may result in hazardous

radiation exposure.

- If this device requires a repair, please wear laser eye

protection with an optical density OD that is 4 or higher and
has a wave length of 459-651 nm.

- Do not place any water-containing vessel on this device,
such as cosmetics or liquid medicine.

- If any object or water enters this device, please unplug this
device and contact the service staff of Hisense.

- Do not place any exposed re source (e.g. burning candle)

on this device. Keep away from high temperature and heat.

- Do not expose the battery to direct sunlight or candle light.

- Keep air vents on both sides clear from any objects to
prevent the device from overheating inside.

- To avoid a short circuit, product damage or electric shock,
do not use any sharp object or metal to touch the ports or
other openings on the TV.

- If this device has been in a warm environment, allow any

built-up condensation to evaporate rst BEFORE you

switch the device on.

- Do not allow a child to stand on or climb up this device.

- Do not place any object above or in front of the lens
because the laser light could cause the object to become

ammable.

- Clean the lens periodically with a clean cloth and make
sure the TV is turned off before you start.

AC voltage: This symbol indicates that the rated voltage marked with the symbol is AC voltage.

Class II product: This symbol indicates that it does not require a safety connection of protective earthing (ground).

F

Congratulations on the purchase of your new TV! This Manual will walk you through a few easy steps to set up your TV.

Please visit Hisense ofcial website for more details.

Product image is only for reference, actual product may vary in appearance.
Parts of the software function changes with the system upgrade.

Table of Contents

Accessories List 2

Laser TV Diagram 3

STEP 1. Mount the Screen 4

STEP 2. Install the Laser TV 4

STEP 3. Adjust the Display Image and the Screen 9

STEP 4. Use Your Remote 13

STEP 5. Proceed through the Screen Setup Menu 16

STEP 6.TV Setup 17

Maintenance & Quick Problem-Solving Tips 18

Product Specications 20

Recycling / Licenses 22

1

• Do not allow a child to stand on or climb up this device.

• Do not place any object above or in front of the lens because the laser light could cause the object to become ammable.

• Clean the lens periodically with a clean cloth and make sure the TV is turned off before you start.

Accessories List

• Laser TV × 1

• Remote control × 1

• AAA batteries × 2

• Gloves for handling the Laser TV × 2

• Power cord × 1

• Wrench to adjust the bottom of the TV × 1

• USB extension cable × 1

• Laser TV User Manual × 1

• Laser TV European Guarantee × 1

• Cleaning kit for the lens × 1

• 2 C-shape blocks

• C-shaped Block Installing Instruction

• RCA Jack to AV Cable × 1

Additional items that come with the TV in a separate package

• A Display Screen (optional equipment)*

• A set of Wall Mount Brackets (optional equipment)*

* Additional items you receive will be based upon your order.

NOTE: The accessories may be different from the list above due to different models, countries/regions. Please refer to the actual

accessory bag.

2

Laser TV Diagram

Remote control receiver

Air vents

Power Indicator

Eye protection sensor

Lens with laser

Foreign Object Detect

Power button

We strongly recommend that two people handle this device when moving it from one place to another. Be sure to
protect the lens when you handle this device.

3

STEP 1 Mount the Screen

Screen installation please refer to the specific screen installation guide!

STEP 2 Install the Laser TV

We strongly recommend that two people handle this device when moving it from one place to another. Be sure to
protect the lens when you handle this device.

We recommend to connect all cables to the ports on the back of the Laser TV before positioning the TV. (Audio, video,
Ethernet cables and external devices are not included.)

Check to ensure that you have selected the right cables for the ports and that they are connected securely. Loose
connections can affect the quality of the picture image and colour.

4

Ethernet (you will need a router for Internet connectivity)

CAM CARD

SMART CARD

NOTE:

(not included)

ANT2 Jack supports power supply for satellite antenna (13/18V, 0.5A max.)

or

Antenna Cable (75Ω)

Satellite antenna

Outdoor

Antenna

VHF/UHF Antenna

Cable

ANT OUT

NOTE:

Before you insert/remove the CI+ module, ensure that the TV is switched off. Then insert the CI card into the CI+ module in accordance with the
Service Provider’s instructions.

Do not repeatedly insert or remove the Common Access Module as this may damage the interface and cause a malfunction.

You must obtain a CI+ module and card from the service provider of the channels you want to watch.

Insert the CI+ module with the SmartCard in the direction marked on the module and SmartCard.

CI+ is not supported in some countries and regions; check with your authorized dealer.

5

NOTE:

When connecting a hard disk or a USB hub, always connect the mains adapter of
the connected device to the power supply. Exceeding a total current consumption
may result in damage. The USB1.1 and USB2.0 devices maximum current
consumption are 500mA.

For individual non-standard high-capacity mobile hard disk, if its impulse current
is greater than or equal 1A, it may cause TV-rebooting or self-locking. So the TV

9

does not support it.

The USB port supports a voltage of 5V.

Use the USB extension cable (included) for easier connection and disconnection.

Excessive sound pressure from earphones

Headphone (not included)

and headphones can cause hearing loss.

External AV devices

Red(R)

HDMI

White(L)

Yellow(Video)

(Cables are not included)

VCR

Set-top Box

Satellite Receiver

DVD Player

Video Camera

External audio devices

9

Digital audio adapter

Speakers

Audio Amplier

6

LAN (

Wired setup

)

Connect your TV to your network by connecting the LAN port on the back of your TV to an external modem or router using a LAN
(Ethernet/Cat 5) cable. See the illustration below.

TV PORT

LAN

IP Sharer (Router)

(with DHCP server)

External Modem

(ADSL / VDSL / Cable TV)

Modem CableLAN CableLAN Cable

Wireless setup

Connect your TV to your network wirelessly, you need a wireless router or modem. See the illustration below.

Wireless router with DHCP

Wireless LAN Adapter

built-in TV set

LAN Cable

NOTE:

You must use the built-in Wireless LAN Adapter to use a wireless network because the set doesn’t support external USB network
adapters.

If the wireless router supports DHCP, your TV can connect more easily to the wireless network.

If you apply a security system other than the systems listed below, it will not work with the TV.
security system: WPA, WEP, WPA2.

In order to guarantee smooth network, the distance between router and TV should be less than 10 metres.

7

Plug the power cord into a wall outlet.

Press the POWER button to turn on the Laser TV

WARNING: Insufficient ventilation space will cause

.

this device to overheat or become damaged.

• Do not block the air vents or place any object on this device.

• Do not place this device in any narrow, enclosed or poorly

ventilated space.

Laser beam

Power Cord

At a minimum, leave the amount of space shown in the diagram
below for this device to have proper ventilation.

15 cm

20 cm

8

20 cm

STEP 3 Adjust the Display Image and the Screen

Follow the steps in the order shown below, only if they apply to your situation.

NOTE: Before adjusting, fold the wall-mount bracket wands so that screen is vertically level. Rotate feet from an overlooking view,

but do not look directely at the lens when the Laser TV is on because the laser light may damage your eyes.

PARALLEL THE BOTTOM OF THE IMAGE WITH THE SCREEN

If the bottom of the image is lower on the left and higher on the
right, rotate the device counterclockwise.

If the bottom of the image is lower on the right and higher on the
left, rotate the device clockwise.

FIT THE BOTTOM OF THE IMAGE TO THE SCREEN

• If the image shifts to the left side, then move the Laser TV to

the right.

If the image shifts to the right side, then move the Laser TV
to the left.

9

• If the bottom of the image is wider than the screen, then

move the Laser TV closer to the screen.

If the bottom of the image is narrower than the screen, then
move the Laser TV farther from the screen.

NOTE: Make sure the bottom of the image always stays

parallel with the screen. If not, rotate the TV following previous
instructions.

ADJUST THE UPPER-RIGHT CORNER OF THE IMAGE

1. If the top of the image is lower on the left and higher on the
right, then use the wrench to rotate the front-right foot and
the back-right foot clockwise to the same height.

back-right foot

front-right foot

2. Now, rotate the TV counterclockwise so that the bottom of
the image is parallel with the screen.

3. Repeat the steps above until the top of the image is parallel
with the screen.

10

4. If the upper-right corner is inside the screen after adjusting,
use the wrench to rotate the front-right foot and the back­right foot counterclockwise to the same height, and rotate
the TV clockwise, to make the image parallel with the
screen.

ADJUST THE UPPER-LEFT CORNER OF THE IMAGE

1. If the top of the image is higher on the left and lower on the
right, then use the wrench to rotate the front-left foot and the
back-left foot of the TV clockwise to the same height.

back-left foot

front-left foot

2. Now, rotate the TV clockwise so that the bottom of the image
is parallel with the screen.

3. Repeat the steps above until the top of the image parallel
with the screen.

4. If the upper-left corner is inside the screen after adjusting,
use the wrench to rotate the front-left foot and the back­left foot counterclockwise to the same height, and rotate the
TV counterclockwise, to make the image is parallel with the
screen.

11

FILL THE TOP OF THE IMAGE TO THE SCREEN

If the top of the image is wider than the screen, then use the
wrench to rotate the left- and right-front feet of the Laser TV
clockwise.

If the top of the image is narrower than the screen, then use
the wrench to rotate the left- and right-back feet of the Laser
TV clockwise, until the left and right borders of the image are
parallel with the screen borders.

Next, move the projector further from the screen to ll the image

to screen width.
If the back feet are already at their maximum height, rotate the
left- and right-front feet counterclockwise.

Rotate the back feet clockwise Rotate the front feet

counterclockwise

12

STEP 4 Use Your Remote

BUTTONS ON YOUR TV REMOTE

NOTE: The button labels are provided as a reference. The actual appearance of the remote that is included with the TV, may differ from this diagram.

1

4

5

7

8

11

12

15

18

2

3

6

9

10

13

14
16

17

19

1

Power Standby button: Power on / Standby

2

Turn on/off the teletext function

3

Select input sources

4

Select a channel or input numbers

5

Display the Electronic Program Guide (DTV

)

mode

6

Display the Channel List on the screen

7

Special function buttons

8

Display the Menu

9

Refer to the diagram on screen to use

and OK to control content playback

/ >

10

OK - Confirm the selection

11

/ / < / >

- Allow you to navigate the OSD

menus and adjust the system settings to
your preference

12

Return to the previous place in the menu or

/ / <

Display the Home screen

14

15

Change volume

16

Change channel (Up/Down)

17

Mute or restore the TV sound

18

APP: Quick access to the app

Note: The information here will vary de­pending on the country/region.

19

: All apps

app

13

Exit the menu

NOTE: The included remote control will vary depending on models, countries / regions. Check

information according to the actual remote control in the accessory bag.

13

BUTTONS ON YOUR TV REMOTE

NOTE: The button labels are provided as a reference. The actual appearance of the remote that is included with the TV, may differ from this diagram.

1

Power button

4

1

2

3

5

2

Turn on/off the teletext function

3

Select input sources

4

Receive the voice (This function is only
supported in some countries or regions.)

5

Number buttons - Direct channel selection
or numbers input

7

9

11

13

15

18
19

22

6

8

10

12

14

16

17
20
21

6

Display the Channel List on the screen

7

Display the Electronic Program Guide (DTV
mode)

8

Special function buttons

9

Display the Menu

10

Refer to the diagram on screen to use

and OK to control content playback

/ >

11

/ / < / >

- Allow you to navigate the OSD

/ / <

menus and adjust the system settings to
your preference

12

OK - Confirm the selection

13

Return to the previous place in the menu or
app

NOTE: The included remote control will vary depending on models, countries / regions. Check

information according to the actual remote control in the accessory bag.

Exit the menu

14

15

Change volume

16

Display the Home screen

17

Change channel (Up/Down)

18

Mute or restore the TV sound

19

: All apps

APP: Quick access to the app

Note: The information here will vary depend­ing on the country/region.

20

Press to activate MIC (This function is only
supported in some countries or regions.)

21

Media mode

22

APP: Quick access to the app

Note: The information here will vary depend­ing on the country/region.

14

1. Press the switch and the battery case
will pop up automatically.

2. Insert two AAA size batteries. Make
sure to match the (+) and ( - ) ends of
the batteries with the (+) and ( - ) ends
indicated in the battery compartment.

3. Push the battery case back to the
remote control.

NOTE: for some models, slide the back

cover to open.

IMPORTANT INFORMATION ABOUT THE REMOTE AND

BATTERIES

• Discard batteries in a designated disposal area. Do not
throw them into a re.

• Remove old batteries immediately to prevent them from

leaking into the battery compartment.

• If you do not intend to use the remote control for a long time,
then remove the batteries.

• Battery chemicals can cause a rash. If the batteries leak,
clean the battery compartment with a cloth. If chemicals
touch your skin then wash it immediately.

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc) or rechargeable

(NiCd, NiMH, etc.) batteries.

• Do not continue using the remote if it gets warm or hot.

• Call our Support Center immediately on the support website.

REMOTE CONTROL RANGE INFORMATION

• The remote control can work at a distance of up to 8 metres

in front of the TV set. (This distance is used by infrared
means in an unpaired state.)

• The remote control angle: taking the remote sensor as an
apex, 6 metres away, its controlled horizontal angle is within
±30°, while the vertical angle is within ±15°. (This angle is
used by infrared means in an unpaired state.)

PAIRING THE REMOTE CONTROL (ONLY FOR BLUETOOTH
REMOTE CONTROL)

1. Pair the remote to the TV after you power it on. Keep the
remote control within 3 metres from the TV. Press and hold
the [ ] button at least 3 seconds to start pairing.

2. If the remote paired successfully then a conrmation will
display on the screen. If it did not pair successfully then an
'unsuccessful' message will display. Repeat step 1.

NOTE:

• If an unknown error occurred with the remote then it could

have been caused by interference. Try to remove what's
causing the interference and pair it again.

• If an unknown error occurred in the remote control while the
battery power is normal, you can take out the batteries and

press any key for 1~2 seconds, then the remote control can

work normally.

• The remote cannot be paired to the TV while the TV is in
standby mode.

15

STEP 5 Proceed through the Screen Setup
Menu

PROJECTION MODE
If you need to ip the image over top-to-bottom and/or left-to-

right, select the Projection Mode.

AUTO GEOMETRIC CORRECTION

Before you use Auto Geometric Correction function, ensure
that the Laser TV and your mobile device are connected to the
same Wi-Fi network.

1. Position the Laser TV and use the leveling feet as needed to

t the entire display border within the screen area.

2. Click Next to continue.

3. Scan the QR Code with your mobile device to begin
automatic geometric correction. When the app loads, the
Laser TV will display an alignment grid.

Alignment grid

4. Click "+" on your mobile device to take a photo of the entire
screen and image. For best results, stand about 10 feet
away from the screen and use landscape mode.

5. Click "upload" on your mobile device to complete the
automatic geometric correction.

MANUAL GEOMETRIC CORRECTION
Select points and move to t the projected image into the

screen.

NOTE:

Manual Geometric Correction is only applicable in some models/
countries/regions.

1. Press

press OK button to choose a point you need to adjust.

2. Long press
projected image;

Short press

projected image.

16

/ / < / >

/ / < / >

/ / < / >

buttons on your remote to move focus, and

buttons: quick adjustment of the

buttons: precise adjustment of the

3. Press button to save your adjustment, and you can select
other points to adjust the image.

If you want to return the image position to the factory default,
select Reset button on the screen.

EYE PROTECTION

In order to protect your eyes, keep the Eye Protection setting
on, and do not look into the lens. If you get too close to the
projector, the light output will be temporarily disabled after 5
second countdown.

STEP 6 TV Setup

Once you are satisfied with the projected image, select "TV

Setup" to configure additional settings, including Network
Connection.

Language

TV Mode

Projection
Mode

Wireless
Network

Select your desired language to be
displayed on the menu.

Select “Home Mode” or “Store Mode”.

Select "Projection Mode".

If your TV does not automatically detect
an Ethernet connection, then use a
wireless network, select your network
from the list that displays, also you can
add a hidden network. When you’re done,
move to the next screen.

Country

Time Zone

Auto
Geometric
Correction

End User
License
Agreement

Enhanced
Viewing

VIDAA
Account
Setup Screen

Select the Country where you will operate
the TV.

Select the local time zone according to
your region.

Select Confirm to clear current settings
and run the automatic geometric
correction app.

Your use of this device is subject to the
End User License Agreement, lack of
your acceptance of the End User License
Agreement will turn off all smart features
of this device. You can choose to turn on/
off each type of smart features separately,
a click to the box of each type of smart
feature means you give your consent to
the corresponding privacy notice/terms
and conditions.

Enhanced viewing can automatically
adjust the picture mode and sound mode
so as to match with the current content
displayed on this device in case it is
recognized by the automatic content
recognition service.
(This function is only applicable in certain
models/countries.)

Link your TV with VIDAA account.

17

Maintenance

• Do not touch this device when it is running or just turned off because it may be hot.

• Do not wipe this device with oil because it may deteriorate the exterior or damage the paint. Contact with rubber or ethylene

products for a long time may cause stains on this device.

• If the outside of the TV is dirty, turn off the TV and wipe with a damped soft cloth.

• Do not touch the lens with your hands.

• Do not touch or wipe the lens with ordinary cleaning cloth. Use a dust blower to remove the dust on the lens. Grease, dirt and
ngerprints should be cleaned carefully by the professional by using optical cleaning cloth, lens wiping paper or professional
cleaning solutions to avoid destroying the optical lming and affecting the image quality.

• To turn off this device, press the Power button on the remote control. Do not cut off the power directly when the device is working.

Quick Problem-Solving Tips

When you experience an issue with your TV, turn it off and on again. If this does not resolve the problem, then refer to the tips below.

When I turn on my TV, there is a delay for a few seconds before the picture appears. Is this normal?
Yes, this is normal. The TV is initializing and searching for previous setting information.

The light output of the projector is disabled.
In this case, if the power indicator illuminates red light for 5 times, please check whether the foreign object detection window is
covered or dirtied. If so, uncover or carefully clean the foreign object detection window.

No sound or picture

1. Check if the power cord is plugged into a powered AC outlet.

2. Press the Power button on the remote control to activate the unit from 'Standby' mode.

3. Check to see if the LED light is on or not. If it is, then the TV is receiving power.

18

I have connected an external source to my TV and I get no picture and/or sound.

1. Check for the correct output connection on the external source and for the correct input connection on the TV.

2. Make sure you have made the correct selection for the input mode for the incoming signal.

The picture is normal but there is no sound

1. Check the volume settings.

2. Check if 'Mute' mode is set to On.

Sound but no picture or black and white picture

1. If the picture is black and white, unplug the TV from the AC outlet and replug it after 60 seconds.

2. Check that the Colour is set to 50 or higher.

3. Try different TV channels.

The sound and/or picture is distorted or appears wavy

1. An electric appliance may be affecting the TV. Turn off any appliances that are nearby and move it farther away from the TV.

2. Insert the power plug of the TV set into another power outlet.

The sound and picture is blurry or cuts out

1. If using an external antenna, check the direction, position and connection of the antenna.

2. Adjust the direction of your antenna or reset or ne tune the channel.

The plastic cabinet makes a "clicking" type of sound
The 'click' sound can occur when the temperature of the television changes. This change causes the television cabinet to expand or

contract, which makes the sound. This is normal and the TV is OK.

The remote control does not work

1. Conrm that TV still has power and is operational.

2. Change the batteries in the remote control.

3. Check if the batteries are correctly installed.

19

Product Specifications

Model Name

Dimension

Weight

Active Screen Size (Diagonal)

Screen resolution

Audio power

Power consumption

Power supply

Receiving
systems

Wireless
LAN Module
specifications

(W × H × D)

Analog

Digital

Model

Frequency Range

Output Power (Max.)

100" Laser TV

24.0 × 6.1 × 13.6 inches
(610 × 155 × 346 mm)

24.7 lbs (11.2 kg)

100 inches

3840 × 2160

2 × 20 W

320 W

120-240V ~ 50/60Hz

PAL-D/K, B/G, I, SECAM-D/K, B/G

DVB-T/T2, DVB-C, DVB-S/S2

WF-M668-UWP1

2.4~2.4835GHz

5.15~5.85GHz

2.4~2.4835GHz 16dBm

5.15~5.25GHz 14dBm

5.25~5.35GHz(DFS Band) 14dBm

5.49~5.71GHz(DFS/TPC Band) 14dBm

5.725~5.85GHz(for Non EU) 14dBm

20

Bluetooth
Module
specifications

Model

Frequency Range

Output Power (Max.)

WF-M668-UWP1

2.4~2.4835GHz

2.4~2.4835GHz,Class1,6dBm

Remote
Control
specifications

Model

Frequency Range

Output Power (Max.)

ERF6A64 / ERF6B64H

2.4~2.4835GHz

2.4~2.4835GHz 5dBm

Temperature: 41°F - 104°F (5°C - 40°C)

Environmental conditions

Humidity: 20% - 80% RH
Atmospheric pressure: 86 kPa - 106 kPa

RGB / 60 Hz (640×480, 800×600, 1024×768)
YUV / 60 Hz (480i, 480p, 720p, 1080i, 1080p)

HDMI Input

YUV / 50Hz (576i, 720p, 1080i, 1080p)
3840×2160 / 24Hz, 3840×2160 / 25Hz, 3840×2160 / 30Hz
3840×2160 / 50Hz, 3840×2160 / 60Hz

Network Standby Power Consumption

Power Consumption in Standby Mode

WIFI

Bluetooth

Disclaimer: All products, product specications, and data are subject to change without notice to improve reliability, function, design or otherwise.

≤ 2.0 W

≤ 0.5 W

IEEE802.11 a/b/g/n/ac

BT5.0

21

Recycling / Licenses

WEEE (Waste Electronic Electric Equipment)
European Directive 2012/19/EU

This symbol on the product or on its packaging indicates that
this product must not be disposed of with your household
waste. Instead, it is your responsibility to dispose of your
waste equipment by handing it over to a designated
collection point for the recycling of waste electrical and
electronic equipment. The separate collection and recycling
of your waste equipment at the time of disposal will help to
conserve natural resources and ensure that it is recycled in
a manner that protects human health and the environment.
For more information about where you can drop off your
waste equipment for recycling, please contact your local city

ofce, your household waste disposal service or the shop

where you purchased the product.

Batteries

In accordance with the Battery Directive, used batteries
should not be disposed of in the domestic waste. Dispose

your batteries in the collection containers specic for this

purpose in retail stores.

ROHS (Restriction of Hazardous Substance)
European Directive 2011/65/EU

This European directive limits the use of dangerous and

hazardous substances which are difcult to recycle.

This allows recycling easily the EEE and contributes to
the safeguard of the environment.

Substances included in this product match to the RoHS
directive.

The terms HDMI and HDMI High-

Denition Multimedia Interface, and

the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing
Administrator, Inc. in the United States
and other countries.

Manufactured under license from Dolby
Laboratories. Dolby, Dolby Atmos, and
the double-D symbol are trademarks

of Dolby Laboratories. Condential

unpublished works. Copyright © 2012-

2019 Dolby Laboratories. All rights

reserved.

22

SIMPLIFIED EU DECLARATION OF CONFORMITY

Hereby, Hisense Visual Technology Co., Ltd. declares that the radio equipment type [100L9GE / 100L9 / 100L9G
/ 100L9GA / 100L9GB / 100L9GC / 100L9GCH / 100L9GTUK / 100L9GTUKA / 100L9GTUKB / 100L9GTUKC /
100L9G-A12 / 100L9G-B12 / 100L9G-C12 / 100L9G-D12 / 100L9GCH-A12 / 100L9GCH-B12 / 100L9GTUK-A12 /
100L9GTUK-B12 / 100L9GTUK-C12 / 100L9GTUK-D12 / ERF6A64 / ERF6B64H] is in compliance with Directive

2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://global.
hisense.com/downloads.

For Great Britain:

SIMPLIFIED UK DECLARATION OF CONFORMITY

Hereby, Hisense Visual Technology Co., Ltd. declares that the radio equipment type [100L9GE / 100L9 / 100L9G
/ 100L9GA / 100L9GB / 100L9GC / 100L9GCH / 100L9GTUK / 100L9GTUKA / 100L9GTUKB / 100L9GTUKC /
100L9G-A12 / 100L9G-B12 / 100L9G-C12 / 100L9G-D12 / 100L9GCH-A12 / 100L9GCH-B12 / 100L9GTUK-A12
/ 100L9GTUK-B12 / 100L9GTUK-C12 / 100L9GTUK-D12 / ERF6A64 / ERF6B64H] is in compliance with Radio

Equipment Regulations 2017. The full text of the UK declaration of conformity is available at the following internet
address: http://global.hisense.com/downloads.

23

ES-A2132Z2-1

24