HIS HIS-ML19- *** G User Manual

19" PANEL MOUNT INDUSTRIAL MONITOR
USER MANUAL
Model No. HIS-ML19- _ _ _ G
REVISION G
2  ML19G User Manual, January 2015
Table of Contents
FCC Notice ����������������������������������������������������������������������������������������������������������������������������� 3 Hazardous Locations ��������������������������������������������������������������������������������������������������������������4 Waste Electrical and Electronic Equipment Directive (WEEE) �����������������������������������������������4
Front and Side Views �������������������������������������������������������������������������������������������������������������� 5 Bottom View ���������������������������������������������������������������������������������������������������������������������������� 5
Step 1: Prepare for Installation ���������������������������������������������������������������������������������������������� 6 Step 2: Bench-test Conguration ������������������������������������������������������������������������������������������� 7
Install Cable Connections ������������������������������������������������������������������������������������������������������������������ 7 Install Touch Screen Driver ���������������������������������������������������������������������������������������������������������������� 8
Step 3: Install into Panel ������������������������������������������������������������������������������������������������������ 10
Video Settings ����������������������������������������������������������������������������������������������������������������12
Setting the Timing Mode ������������������������������������������������������������������������������������������������������� 12 Control Panel Buttons �����������������������������������������������������������������������������������������������������������13 OSD and Power Lock Settings ��������������������������������������������������������������������������������������������� 14 On-Screen Display (OSD) Menus ����������������������������������������������������������������������������������������� 15
Auto Image Adjust Menu ������������������������������������������������������������������������������������������������������������������ 16 Contrast / Brightness Menu�������������������������������������������������������������������������������������������������������������� 16 Input Select Menu ���������������������������������������������������������������������������������������������������������������������������� 16 Color Adjust Menu ���������������������������������������������������������������������������������������������������������������������������� 16 Information Menu ����������������������������������������������������������������������������������������������������������������������������� 17 Manual Image Adjust Menu�������������������������������������������������������������������������������������������������������������� 18 Setup Menu �������������������������������������������������������������������������������������������������������������������������������������� 19 Memory Recall Menu ����������������������������������������������������������������������������������������������������������������������� 19
Cleaning Instructions ����������������������������������������������������������������������������������������������������20 Troubleshooting ������������������������������������������������������������������������������������������������������������21
Video Troubleshooting ����������������������������������������������������������������������������������������������������������21 Touch Screen Troubleshooting ��������������������������������������������������������������������������������������������� 23
Specications ����������������������������������������������������������������������������������������������������������������24
Display ����������������������������������������������������������������������������������������������������������������������������������24 Physical ��������������������������������������������������������������������������������������������������������������������������������24 Video ������������������������������������������������������������������������������������������������������������������������������������� 25 Electrical ������������������������������������������������������������������������������������������������������������������������������� 25 Functional ����������������������������������������������������������������������������������������������������������������������������� 25 Environmental �����������������������������������������������������������������������������������������������������������������������26 Compliances and Certications �������������������������������������������������������������������������������������������� 26
Warranty Statement �������������������������������������������������������������������������������������������������������27
Safety and Regulatory Information
ML19G User Manual, January 2015   3
To prevent re or shock hazard, do not expose live components to rain or moisture�   Dangerously high voltages are present inside the unit�  Do not disassemble the unit�   Refer servicing to qualied personnel only�
This equipment is not intended for use in critical applications where its failure  to operate would create immediate life threatening circumstances�  Applications  including, but not limited to, nuclear reactor control, aerospace navigation systems  and life support systems are not appropriate for this product�
This product is intended to be mounted in a suitable cabinet or other enclosure�   The NEMA 4, 4X, or 12 ratings are applicable only when properly installed in a like  rated enclosure�
To be covered by UL 60950 3rd Edition, the socket-outlet shall be installed near the  equipment and shall be easily accessible�
DC Supplied Units only:  The HISML19 subject unit is to be powered by a Listed  Power Supply suitable for the application with outputs at SELV/LPS or Class 2 levels  rated 9�6-36�6VDC, 2�5 A max� The equipment is not intended to connect directly to a  DC Mains source�
FCC Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules� These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment� This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications� Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense� Any changes or modications not expressly approved by the grantee of this device could void the user’s authority to operate the device�
Safety and Regulatory Information
WARNING!
!
Safety and Regulatory Information
4  ML19G User Manual, January 2015
Waste Electrical and Electronic Equipment Directive (WEEE)
The following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE)�
The mark indicates the requirement NOT to dispose of the equipment as unsorted municipal waste, but use the return and collection systems according to local law� Users should contact their supplier and check the terms and conditions of the purchase contract� When purchased directly from Hope Industrial Systems, you may contact technical support for disposal arrangements�
Hazardous Locations
The following applies only to monitors rated for hazardous locations (model numbers HIS-ML19-
_ _
HG and HIS-ML19-
_ _
UG):
This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D; Class II, Division 2, Groups F and G; Class III; or non-hazardous locations only�
Device is open-type and is to be installed in an enclosure suitable for the environment that is only accessible with the use of a tool�
WARNING – EXPLOSION HAZARD – Do not disconnect equipment unless power has been removed or the area is known to be non-hazardous�
WARNING – EXPLOSION HAZARD – Substitution of any components may impair suitability for Class I, II & III, Division 2 Locations�
Mechanical Drawings
ML19G User Manual, January 2015   5
Mechanical Drawings
Front and Side Views
Bottom View
332.4 mm (13.09")
7.1 mm (0.28")
398.8 mm (15.70")
482.6 mm (19.00")
376 mm
(14.8")
301 mm
(11.9")
61.6 mm (2.43")
409.8 mm (16.14")
482.6 mm (19.00")
7.1 mm (0.28")
(Design to maximum depth of 69.0 mm to ensure future compatibility with later revisions and replacement units.)
Installation Instructions
6  ML19G User Manual, January 2015
Installation Instructions
Step 1:  Prepare for Installation
IMPORTANT!
Perform the following steps BEFORE installation of the monitor into the panel�
1� Ensure that sufcient power is available�
2� Ensure that sufcient space is available to allow for proper air ow into and out of the
unit�
3� Ensure that the air temperature around the unit (top and bottom) will not exceed the
rated specications of the unit.
f The maximum rated temperature for the HIS-ML19 is 50°C (122°F)�
f Remember  that  heat  rises  –  the  temperature  at  the  top  of  the 
cabinet  will  be  much  hotter  than  at  the  bottom  if  air  inside  the  enclosure is not actively circulating�  Even in a sealed enclosure,  use of a circulation fan can greatly reduce temperature�
f Also,  remember  that  even  though  this  product  is  designed  to 
operate at 50°C, the life span of any electronic device is shortened  when it is consistently operated at high temperatures�  Therefore,  it is wise to take steps to keep the temperature of the ambient air  around the unit as low as possible�
4� Ensure that the ambient humidity of the air around the unit does not exceed the
specications of the unit.
f The  maximum  rated  humidity  for  the  HIS-ML19  is  90%                                               
non-condensing�
!
Installation Instructions
ML19G User Manual, January 2015   7
Step 2:  Bench-test Conguration
Make sure everything works before installing into the production environment�
TIP!
If using a KVM extender, please refer to the installation instructions included  with the KVM extender module�  It is particularly important to bench-test the full  conguration prior to nal installation�  This will help to identify and troubleshoot  any system issues while conguration changes may still be easily made�
Install Cable Connections
All monitors are shipped with both a 6 ft� (1�8 m) VGA video cable and 6 ft� (1�8 m) power cable, unless longer cables were ordered in their place� DC models are shipped with a bench test power supply� If you ordered a touch screen monitor, you also received a 6 ft� (1�8 m) USB cable, unless a longer cable was ordered in its place� Serial (RS-232) cables may be ordered separately�
The cable ports are located on the rear of the monitor� Refer to the following diagram and instructions to connect power, video, and touch screen (if applicable) to your monitor�
Video Connection
The HIS-ML19 supports analog and digital video�
Analog VGA Video Connection
Connect one end of the VGA video cable to the HD-15 input port on the rear of the monitor� Connect the other end to the analog video output port on the host computer�
Digital DVI Video Connection
Connect one end of the DVI video cable to the DVI-D input port on the rear of the monitor� Connect the other end to the digital video output port on the host computer�
DIGITAL VIDEO
USB
(for Touch Screen option)
SERIAL
(RS-232)
POWER INPUT
ANALOG VIDEO
Installation Instructions
8  ML19G User Manual, January 2015
TIP!
If the video source has an HDMI or DisplayPort connection, this can be converted to  DVI with a simple adapter�  Contact Hope Industrial Systems for more information�
Power Connection
The HIS-ML19 is available with either AC or DC power input�
AC power input models are powered by 100 to 240 VAC, 1�5/0�75 A, 60/50 Hz� Connect the AC power cable to the power input port on the rear of the monitor� Connect the other end into a nearby outlet�
DC power input models are powered by 9�6 to 36�6 VDC, 2�5 to 0�65 A, Class 2 or SELV/LPS� A power supply is provided for bench testing the monitor� First connect the DC power connector to the power input port on the rear of the monitor� Then connect the AC end into a nearby outlet�
Install Touch Screen Driver
Applies to touch screen monitors only� Instructions below apply to Windows systems� Both Serial and USB ports are present on all touch screen monitors, but only one should be used to connect the touch screen interface to the monitor�
All touch screen monitors are shipped with a CD-ROM that contains documentation and drivers for all major operating systems� To be sure that you have the most current information, please check the following Internet address:
http://www�HopeIndustrial�com/Touchscreen_Drivers�htm
IMPORTANT!
If you will be using a USB connection, install the touch screen driver rst, and then  connect the USB cable�  If you will be using a Serial connection, connect the Serial cable rst, and then install the touch screen driver�
Installation Instructions
ML19G User Manual, January 2015   9
USB Connection
1� Select the appropriate driver for your operating system�
a� If downloading from the web address listed above, select the appropriate
driver for your operating system�
b� If using the included CD, insert it into the host computer's CD-ROM drive�
If the CD does not automatically run, browse the contents of the CD and open the READ�ME�FIRST�htm le in a web browser� Select the appropriate driver�
2� Click to "Run" the software when prompted� Follow on-screen instructions to
download and execute the touch screen driver installation�
3� A cable retention bracket comes installed on the USB port on the rear of the monitor
and will help to secure the cable and ensure adequate strain relief� Without removing the bracket, route one end of the USB cable through the retention bracket and connect it to the USB input port on the monitor� Connect the other end to the USB port on the host computer�
Serial (RS-232) Connection
1� Connect one end of the Serial cable to the Serial input port on the rear of the monitor�
Connect the other end to the Serial port on the host computer� Tighten the captive screws on the cable connectors to ensure adequate strain relief�
2� Select the appropriate driver for your operating system�
a� If downloading from the web address listed above, select the appropriate
driver for your operating system�
b� If using the included CD, insert it into the host computer's CD-ROM drive�
If the CD does not automatically run, browse the contents of the CD and open the READ�ME�FIRST�htm le in a web browser� Select the appropriate driver�
3� Click to "Run" the software when prompted� Follow on-screen instructions to
download and execute the touch screen driver installation�
Calibrate the Touch Screen
Once the driver has nished installing, you are ready to calibrate the touch screen� Open the touch screen's Control Panel by clicking on the "Elo Touchscreen" icon, located in the host computer's Control Panel� Under the "General" tab, click the "Align" button to start the calibration routine�
Loading...
+ 19 hidden pages