Hirschmann SPIDER-SL-40-08T1 User Manual

User Manual

Installation
Industrial Ethernet Rail Switch

SPIDER-SL-40-08T1

Installation SPIDER-SL-40-08T1

Release 01 08/2015

https://hirschmann-support.belden.eu.com

Technical support

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.

© 2015 Hirschmann Automation and Control GmbH

Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD/DVD applies.

The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).

Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]

SPIDER-SL-40-08T1 040 101-001-01-0815 - 27.8.15

Contents

Safety instructions 4

About this Manual 9

Legend 9

1 Description 10

1.1 General device description 10

1.2 Device name and product code 11

1.3 Device view 12

1.4 Power supply 12

1.5 10/100/1000 Mbit/s twisted pair port 13

1.6 Pin assignments 13

1.7 Display elements 14

1.7.1 Device state 14

1.7.2 Port state 14

2 Installation 15

2.1 Checking the package contents 15

2.2 Mounting the device 16

2.3 Wiring the terminal block for the supply voltage and the
grounding 17

2.4 Operating the device 18

2.5 Connecting data cables 18

3 Monitoring the ambient air temperature 19

4 Maintenance and service 20

5 Disassembly 21

6 Technical data 22

A Further Support 27

Installation SPIDER-SL-40-08T1

Release 01 08/2015

3

Safety instructions

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,
or equipment damage.

 General safety instructions

You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
 Before connecting any cable, read this document, and the safety

instructions and warnings.

 Operate the device with undamaged components exclusively.
 The device is free of any service components. In case of a damaged

or malfunctioning the device, turn off the supply voltage and return the
device to Hirschmann for inspection.

 Certified usage

 Use the product only for the application cases described in the

Hirschmann product information, including this manual.

 Operate the product only according to the technical specifications.

See “Technical data” on page 22.

 Connect to the product only components suitable for the requirements

of the specific application case.

Installation SPIDER-SL-40-08T1

4

Release 01 08/2015

 Device casing

Only technicians authorized by the manufacturer are permitted to open
the casing.
 Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not
touch the connection terminals.

 Keep the ventilation slits free to ensure good air circulation.

See “General technical data” on page 22.

 Install the device in the vertical position.

 Qualification requirements for personnel

 Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

 Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.

 Qualified personnel are aware of the dangers that exist in their work.
 Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

 Qualified personnel receive training on a regular basis.

 National and international safety regulations

Verify that the electrical installation meets local or nationally applicable
safety regulations.

 Grounding the device

The device is grounded by means of a 3-pin terminal block.
 Use a wire diameter for the ground conductor that is no smaller than

the diameter of the supply voltage connection, however of at least

0.5 mm² (AWG20).

 Shielding ground

The shielding ground of the connectable twisted pair cables is connected
to the ground connection as a conductor.
 Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

Installation SPIDER-SL-40-08T1

Release 01 08/2015

5

 Requirements for connecting electrical wires

Before connecting the electrical wires, always verify that the
requirements listed are complied with.

General requirements for connecting electrical wires
The following requirements apply without restrictions:

 The electrical wires are voltage-free.
 The cables used are permitted for the temperature range of the application case.
 The voltage connected complies with the requirements for a safety extra-low voltage

(SELV) as per IEC/EN 60950-1.

 Relevant for North America:

Use 60/75 or 75 °C copper (Cu) wire only.

Requirements for connecting the supply voltage
The following requirements apply without restrictions:

 The supply voltage corresponds to the voltage specified on the type plate of the device.
 The power supply conforms to overvoltage category I or II.
 The power supply has an easily accessible disconnecting device (e.g., a switch or a plug).

This disconnecting device is clearly identified. So in the case of an emergency, it is clear
which disconnecting device belongs to which power supply cable.

 The power supply cable is suitable for the voltage, the current and the physical load.

Hirschmann recommends a wire diameter of 0.5 mm² (AWG20).

 The cross-section of the ground conductor is the same size as or bigger than the cross-

section of the power supply cables.

The following requirements apply alternatively:

Alternative 1 The power supply complies with the requirements for a limited power source

(LPS) as per EN 60950-1.

Alternative 2 All of the following requirements are complied with:

 The powersupply complies with the requirements for a safety extra-low

voltage (SELV) as per IEC/EN 60950-1.

 A fuse suitable for DC voltage is located in the plus conductor of the power

supply.
The minus conductor is on ground potential. Otherwise, a fuse is also
located in the minus conductor.
Regarding the properties of this fuse: See “General technical data” on

page 22.

Alternative 3 Relevant for North America:

The power supply complies with the requirements as per NEC Class 2

 Supply voltage

The supply voltage is only connected with the ground connection via
protective elements.

6

Installation SPIDER-SL-40-08T1

Release 01 08/2015

 CE marking

The labeled devices comply with the regulations contained in the following
European directive(s):

2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.

2004/108/EC (EMC)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic
compatibility.

In accordance with the above-named EU directive(s), the EU conformity
declaration will be available to the relevant authorities at the following
address:

Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]

The device can be used in the industrial sector.

 Interference immunity: EN 61000-6-2
 Emitted interference: EN 55022

You find more information on technical standards here:

“Technical data” on page 22

The assembly guidelines provided in these instructions must be strictly
adhered to in order to observe the EMC threshold values.

Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.

Installation SPIDER-SL-40-08T1

Release 01 08/2015

7

 FCC note:

This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate these
frequencies. If it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a residential area can also cause interference, and in this
case the user is obliged to cover the costs of removing the interference.

 Recycling note

After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

8

Installation SPIDER-SL-40-08T1

Release 01 08/2015

About this Manual

The “Installation User Manual” document contains a device description,
safety instructions, a display description and further information that you
require to install the device.

Legend

The symbols used in this manual have the following meanings:

 Listing

 Work step

Subheading



Installation SPIDER-SL-40-08T1

Release 01 08/2015

9

1 Description

1.1 General device description

The SPIDER-SL-40-08T1 devices are designed for the special requirements
of industrial automation. They meet the relevant industry standards, provide
very high operational reliability, even under extreme conditions, and also
long-term reliability and flexibility.

You have the ability to connect end devices or other segments to the ports of
the device via twisted-pair cables.

The devices work without a fan.

The device is mounted by latching in place on a DIN rail.

10

Installation SPIDER-SL-40-08T1

Release 01 08/2015

1.2 Device name and product code

The device name corresponds to the product code. The product code is
made up of characteristics with defined positions. The characteristic values
stand for specific product properties.

Item Characteristic Character

istic value

1 ... 9 Product Spider SL Spider Standard Line

10 (hyphen) –
11 Data rate 4 10/100/1000 Mbit/s
12 Power over Ethernet (PoE) 0 without
13 (hyphen) –
14 ... 17 Twisted pair ports 08 8 × RJ45 socket

T1 Twisted pair
18 ... 19 Optical fiber port 1 99 without
20 ... 21 Optical fiber port 2 99 without
22 ... 23 Optical fiber port 3 99 without
24 Temperature range S Standard 0 °C ... +60 °C

25 ... 26 Certificates and declarations Z9 CE, FCC, EN 61131-2, EN 60950-1
27 ... 28 Customer-specific version HH Hirschmann Standard
29 ... 30 Configuration HH Hirschmann Standard

Description

Gigabit Ethernet switch

(+32 °F ... +140 °F)

Table 1: Device name and product code

Installation SPIDER-SL-40-08T1

Release 01 08/2015

11

1.3 Device view

1

2

12

4

3

3

56

78

4

Overview of the device elements
1 3-pin, pluggable terminal block for power supply
2 LED display element for device status
3 8 × RJ45 socket for 10/100/1000 Mbit/s Twisted Pair connections
4 Rail lock gate for DIN rail mounting

1.4 Power supply

For the power supply of the device, a 3-pin terminal block is available.

For further information see “Wiring the terminal block for the supply voltage

and the grounding” on page 17.

12

Installation SPIDER-SL-40-08T1

Release 01 08/2015

1.5 10/100/1000 Mbit/s twisted pair port

This port is an RJ45 socket.
The 10/100/1000 Mbit/s twisted pair port offers you the ability to connect
network components according to the IEEE 802.3 10BASE-T/100BASE­TX/1000BASE-T standard.
This port supports:

 Autonegotiation
 Autopolarity
 Autocrossing
 1000 Mbit/s full duplex
 100 Mbit/s half-duplex mode, 100 Mbit/s full duplex mode
 10 Mbit/s half-duplex mode, 10 Mbit/s full duplex mode

1.6 Pin assignments

RJ45 Pin 10/100 Mbit/s 1000 Mbit/s

1 TX+ BI_DA+

1

2TX− BI_DA−

2

3 RX+ BI_DB+

3
4

4— BI_DC+

5

5— BI_DC−

6

6RX− BI_DB−

7

7— BI_DD+

8

8— BI_DD−

Installation SPIDER-SL-40-08T1

Release 01 08/2015

13

1.7 Display elements

After the working voltage is set up, the software starts and initializes itself.
Afterwards, the device performs a self-test. During this process, various
LEDs light up.

1.7.1 Device state

This LED provides information on the status of the power supply.

Color Activity Meaning

Green Lights up Supply voltage is on

Device is ready for operation

None Supply voltage is too low

Device is not ready for operation

1.7.2 Port state

1

12

2
3

3

56

7

4

4
5

6
7

8

8

This LED shows port-related information.

Color Activity Meaning

Green Lights up Device detects a valid link

Flashing Device is transmitting and/or receiving data
None Device detects an invalid or missing link

14

Installation SPIDER-SL-40-08T1

Release 01 08/2015

2Installation

The devices have been developed for practical application in a harsh
industrial environment.
On delivery, the device is ready for operation.

To configure a subdomain, follow these steps:

 Checking the package contents
 Mounting the device
 Wiring the terminal block for the supply voltage and the grounding
 Operating the device
 Connecting data cables

2.1 Checking the package contents

 Check whether the package includes all items named in the section

“Scope of delivery” on page 25.

 Check the individual parts for transport damage.

Installation SPIDER-SL-40-08T1

Release 01 08/2015

15

2.2 Mounting the device

The device is for mounting on a 35 mm DIN rail in accordance with DIN EN

60715.

1

2

To mount the device onto a horizontally mounted 35 mm DIN rail according
to DIN EN 60715, proceed as follows:

 Slide the upper snap-in guide of the device into the DIN rail.
 Press the media module downwards onto the clip-in bar.
 Snap in the device.

16

Installation SPIDER-SL-40-08T1

Release 01 08/2015

2.3 Wiring the terminal block for the supply

voltage and the grounding

WARNING

ELECTRIC SHOCK

Connect only a supply voltage that corresponds to the type plate of your
device.
Never insert sharp objects (small screwdrivers, wires, etc.) into the
connection terminals for the supply voltage, and do not touch the terminals.

Failure to follow these instructions can result in death, serious injury,
or equipment damage.

A 3-pin terminal block is used for the grounding and for connecting the supply
voltage.
The supply voltage is only connected with the ground connection via
protective elements.
The shielding ground of the connectable twisted pair cables is connected to
the ground connection as a conductor.

0 V

24 V

Figure 1: 3-pin, pluggable terminal block for power supply and grounding

Type of the voltages
that can be
connected

DC voltage Rated voltage range DC

Table 2: Type and specification of the supply voltage and pin assignment on the

device

Specification of the supply
voltage

12 V ... 24 V
Voltage range DC incl. maximum
tolerances

9.6 V ... 32 V

Connections

24 V Plus terminal of the supply

voltage

0 V Minus terminal of the supply

voltage
Functional ground connection

Installation SPIDER-SL-40-08T1

Release 01 08/2015

17

Proceed as follows:
 Ensure the required conditions for connecting the supply voltage.

See “Requirements for connecting electrical wires” on page 6.

 Pull the terminal block off the device.
 Connect the ground connection.
 Connect the power supply cables.
 Plug the terminal block into the connection on the housing.

2.4 Operating the device

By connecting the supply voltage via the terminal block, you start the
operation of the device.

2.5 Connecting data cables

Note the following general recommendations for data cable connections in
environments with high electrical interference levels:

 Keep the length of the data cables as short as possible.
 Use optical data cables for the data transmission between the buildings.
 When using copper cables, provide a sufficient separation between the

power supply cables and the data cables. Ideally, install the cables in
separate cable channels.

 Verify that power supply cables and data cables do not run parallel over

longer distances, and that ideally they are installed in separate cable
channels. If reducing the inductive coupling is necessary, verify that the
power supply cables and data cables cross at a 90° angle.

 Use shielded cables (SF/UTP cables as per ISO/IEC 11801:2002).
 Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

 Connect the data cables according to your requirements.

18

Installation SPIDER-SL-40-08T1

Release 01 08/2015

3 Monitoring the ambient air temperature

Operate the device below the specified maximum ambient air temperature
exclusively.

See “General technical data” on page 22.

The ambient air temperature is the temperature of the air at a distance of 2 in
(5 cm) from the device. It depends on the installation conditions of the device,
e.g. the distance from other devices or other objects, and the output of
neighboring devices.

Installation SPIDER-SL-40-08T1

Release 01 08/2015

19

4 Maintenance and service

When designing this device, Hirschmann largely avoided using high-wear
parts. The parts subject to wear and tear are dimensioned to last longer than
the lifetime of the product when it is operated normally. Operate this device
according to the specifications.
Depending on the degree of pollution in the operating environment, check at
regular intervals that the ventilation slots in the device are not obstructed.

CAUTION

RISK OF TRANSIENTS OR ELECTROSTATIC DISCHARGES

Do not open the housing.

Failure to follow these instructions can result in injury or equipment
damage.

Note: You will find information about the complaints and returns procedures

on the Internet under

http://www.beldensolutions.com/en/Service/Repairs/index.phtml .

20

Installation SPIDER-SL-40-08T1

Release 01 08/2015

5Disassembly

1

2

Proceed as follows:

 Disconnect the data cables.
 Disable the supply voltage.
 Remove the power connector from the device.
 Use a screwdriver to pull the rail lock gate downwards.
 Pull the device downwards from the DIN rail module.

Installation SPIDER-SL-40-08T1

Release 01 08/2015

21

6 Technical data

 General technical data

Dimensions
W × H × D

Weight SPIDER-SL-40-08T1 170 g
Power supply

Potential
difference between
incoming voltage
and housing

Climatic conditions
during operation

Climatic conditions
during storage

Pollution degree 2
Protection classes Degree of protection IP 30

SPIDER-SL-40-08T1 See “Dimension drawings” on page 23.

 1 voltage input
 3-pin terminal block
 Safety extra-low voltage (SELV)

Rated voltage range DC 12 V ... 24 V

Class 2

Voltage range DC incl. maximum
tolerances

Current consumption at 24 V DC 0.2 A
Power loss buffer 10 ms at 20.4 V DC
Back-up fuse ≤ 4 A, slow blow
Peak inrush current 4 A
Potential difference from

incoming voltage +24 V DC
Potential difference from

incoming voltage, ground
Ambient air temperature

Humidity 10 % ... 95 %

Air pressure minimum 795 hPa (+9842 ft; +2000 m)
Ambient air temperature

Humidity 10 % ... 95 %

Air pressure minimum 700 hPa (+9842 ft; +3000 m)

a

a

9.6 V ... 32 V

+32 V DC

−32 V DC

+32 °F ... +140 °F
(0 °C ... +60 °C)

(non-condensing)

−40 °F ... +158 °F
(−40 °C ... +70 °C)

(non-condensing)

a. Temperature of the ambient air at a distance of 2 inches (5 cm) from the device

22

Installation SPIDER-SL-40-08T1

Release 01 08/2015

 Dimension drawings

14

102

38

736

Installation SPIDER-SL-40-08T1

Release 01 08/2015

23

 EMC and immunity

EMC interference
emission

Radiated emission

FCC 47 CFR Part 15 Class A
EN 55022 Class A

Conducted emission

FCC 47 CFR Part 15 Class A
EN 55022 Class A

EMC interference
immunity

Electrostatic discharge

EN 61000-4-2
IEEE C37.90.3

EN 61000-4-2
IEEE C37.90.3

Electromagnetic field

EN 61000-4-3 80 MHz ... 1000 MHz 10 V/m

Fast transients (burst)

EN 61000-4-4
IEEE C37.90.1

EN 61000-4-4
IEEE C37.90.1

Voltage surges - DC supply connection

EN 61000-4-5 line/ground 2 kV
EN 61000-4-5 line/line 1 kV

Voltage surges - data line

EN 61000-4-5 line/ground 1 kV

Conducted disturbances

EN 61000-4-6 150 kHz ... 80 MHz 10 V

Contact discharge ± 4 kV

Air discharge ± 8 kV

DC supply connection 2 kV

Data line 4 kV

Stability

IEC 60068-2-6, test Fc Vibration 5 Hz ... 8.4 Hz with

IEC 60068-2-27, test Ea Shock 15 g at 11 ms

 Network range

10/100/1000 Mbit/s twisted pair port

Length of a twisted pair segment max. 100 m (for cat5e cable)

24

3.5 mm amplitude

8.4 Hz ... 150 Hz with 1 g

Installation SPIDER-SL-40-08T1

Release 01 08/2015

 Power consumption/power output at 24 V DC

Device name Max. power consumption Power output

SPIDER-SL-40-08T1 4.8 W 16.4 Btu (IT)/h

 Scope of delivery

Number Article

1 × Device
1 × 3-pin, pluggable terminal block for power supply
1 × Safety Information



Order number

Device Order number

SPIDER-SL-40-08T1 942 132-004

 Accessories

Note that products recommended as accessories may have different
characteristics to those of the device, which may limit the application
range of the overall system. For example, if you add an accessory with IP
20 to a device with IP 65, the IP of the overall system is reduced to 20.

Other accessories Order number

3-pin Low Voltage Interlock terminal block (50 pcs.) 943 845-005
Rail Power Supply RPS 30 943 662-003
Rail Power Supply RPS 80 EEC 943 662-080
Rail Power Supply RPS 120 EEC (CC) 943 662-121

Installation SPIDER-SL-40-08T1

Release 01 08/2015

25

 Underlying technical standards

Name

CSA C22.2 No. 142 Canadian National Standard(s) – Process Control Equipment –

Industrial Products

EN 55022 Information technology equipment – Radio disturbance

characteristics – Limits and methods of measurement

EN 60950-1 Information technology equipment – Safety – Part 1: General

requirements

EN 61000-6-2 Electromagnetic compatibility (EMC) – Part 6-2: Generic

standards – Immunity for industrial environments

EN 61131-2 Programmable controllers – Part 2: Equipment requirements and

tests
FCC 47 CFR Part 15 Code of Federal Regulations
UL/IEC 61010-1,

UL/IEC 61010-2-201

Safety for Control Equipment

Table 3: List of the technical standards

The device has an approval based on a specific standard only if the
approval indicator appears on the device casing.
The device generally fulfills the technical standards named in their current
versions.

26

Installation SPIDER-SL-40-08T1

Release 01 08/2015

A Further Support

 Technical Questions

For technical questions, please contact any Hirschmann dealer in your
area or Hirschmann directly.

You will find the addresses of our partners on the Internet at

http://www.hirschmann.com

Contact our support at

https://hirschmann-support.belden.eu.com

You can contact us

in the EMEA region at

 Tel.: [phone]
 E-mail: [e-mail]

in the America region at

 Tel.: [phone]
 E-mail: [e-mail]

in the Asia-Pacific region at

 Tel.: [phone]
 E-mail: [e-mail]

 Hirschmann Competence Center

The Hirschmann Competence Center is ahead of its competitors:

 Consulting incorporates comprehensive technical advice, from system

evaluation through network planning to project planning.

 Training offers you an introduction to the basics, product briefing and

user training with certification.
The current technology and product training courses can be found at

http://www.hicomcenter.com

 Support ranges from the first installation through the standby service

to maintenance concepts.

With the Hirschmann Competence Center, you have decided against
making any compromises. Our client-customized package leaves you
free to choose the service components you want to use.
Internet:

http://www.hicomcenter.com

Installation SPIDER-SL-40-08T1

Release 01 08/2015

27