Hirschmann SPIDER 3TX-TAP SPIDER 5TX, SPIDER 5TX EEC, SPIDER 8TX, SPIDER 8TX EEC, SPIDER 1TX/1FX User guide
...
Description and operating instructions
Industrial ETHERNET Rail Switch
SPIDER xTX(/xFX)
The Rail Switches / media converters
– SPIDER 3TX-TAP
– SPIDER 5TX
– SPIDER 5TX EEC
– SPIDER 8TX
– SPIDER 8TX EEC
– SPIDER 1TX/1FX (media converter)
– SPIDER 1TX/1FX EEC (media converter)
– SPIDER 1TX/1FX-SM (media converter)
– SPIDER 1TX/1FX-SM EEC (media converter)
– SPIDER 4TX/1FX
– SPIDER 4TX/1FX EEC
– SPIDER 4TX/1FX-ST EEC
– SPIDER 4TX/1FX-SM EEC
in short SPIDER, are switches especially
designed for use in industrial environments.
It supports ETHERNET 10 MBit/s and Fast
ETHERNET 100 MBit/s.
The devices support switched ETHERNET
networks in accordance with IEEE standard
802.3 or 802.3u using copper and fiber optic
technology. The devices are plugged onto
the standard bar.
The SPIDER 3TX-TAP (SPIDER 5TX, SPIDER
5TX EEC, SPIDER 8TX, SPIDER 8TX EEC)
devices have three (five, eight) 10/100
MBit/s twisted pair ports (RJ45 connectors).
It is possible to connect up to three (five,
eight) data terminal equipments or other
network segments to the TP ports using twisted pair cabling.
The SPIDER 1TX/1FX... devices have one
10/100 MBit/s twisted pair port (RJ45
connectors) and one 100 MBit/s fiber optic
port (100BASE-FX, Duplex SC connector). It
is possible to connect one data terminal
equipments or other network segments to
the TP ports using twisted pair cabling. One
further DTE or optical network component
can be connected to the fiber port.
The SPIDER 4TX/1FX... devices have four
10/100 MBit/s twisted pair ports (RJ45
connectors) and one 100 MBit/s fiber optic
port (100BASE-FX, Duplex SC connector or
ST connector on SPIDER 4TX/1FX-ST EEC).
It is possible to connect up to four data
terminal equipments or other network
segments to the TP ports using twisted pair
cabling. One further DTE or optical network
component can be connected to the fiber
port.
The TP ports support autonegotiation, autopolarity and autocrossing.
The fiber optic port of the SPIDER
1TX/1FX... and SPIDER 4TX/1FX... supports
full duplex (FDX).
Hirschmann. Simply a good Connection.
P
x
SPIDER 3TX-TAP SPIDER 5TX
P
x
DA/STAT
SPIDER 4TX/1FX
SPIDER 4TX/1FX EEC
SPIDER 4TX/1FX-SM EEC
039669004030706000
SPIDER 5TX EEC
P
x
P
x
DA/STAT
SPIDER 4TX/1FX-ST EEC SPIDER
P
SPIDER 8TX
SPIDER 8TX EEC
x
P
x
DA/STAT
SPIDER 1TX/1FX
SPIDER 1TX/1FX EEC
SPIDER 1TX/1FX-SM
SPIDER 1TX/1FX-SM EEC
2
The performance features described here
are binding only if they have been expressly
guaranteed in the contract. We have
checked that the contents of the technical
publication agree with the hardware and
software described. However, it is not possible to rule out deviations completely, so we
are unable to guarantee complete agreement. However, the details in the technical
publication are checked regularly. Any corrections which prove necessary are contained in subsequent editions. We are grateful
for suggestions for improvement.
We reserve the right to make technical
modifications.
Permission is not given for the circulation
or reproduction of this document, its use or
the passing on of its contents unless granted expressly. Contravention renders the
perpetrator liable for compensation for
damages. All rights reserved, in particular
in the case of patent grant or registration of
a utility or design.
Copyright
© Hirschmann
Automation and Control GmbH 2006
All Rights Reserved
Note
We would point out that the content of
these operating instructions is not part of,
nor is it intended to amend an earlier or existing agreement, permit or legal relationship. All obligations on Hirschmann arise
from the respective purchasing agreement
which also contains the full warranty conditions which have sole applicability. These
contractual warranty conditions are neither
extended nor restricted by comments in
these operating instructions.
We would furthermore point out that for
reasons of simplicity, these operating
instructions cannot describe every
conceivable problem associated with the
use of this equipment. Should you require
further information or should particular
problems occur which are not treated in
sufficient detail in the operating instructions, you can request the necessary information from your local Hirschmann sales
partner or directly from the Hirschmann
office (address: refer to chapter entitled
„Notes on CE identification“).
Safety Instructions
This manual contains instructions which
must be observed to ensure your own personal safety and to avoid
damage to devices and machinery. The
instructions are highlighted with a warning
triangle and are shown as
follows according to the degree of endangerment:
z
Danger!
means that death, serious injury or
considerable damage to property
will result if the appropriate safety
measures are not taken.
z
Warning!
means that death, serious injury or
considerable damage to property
can result if the appropriate safety
measures are not taken.
z
Caution!
means that light injury or damage to
property can result if the appropriate safety measures are not taken.
Note: is an important piece of information
about the product, how to use the product,
or the relevant section of the documentation to which particular attention is to be
drawn.
Certified usage
Please observe the following:
z
Warning
The device may only be employed
for the purposes described in the
catalog and technical description,
and only in conjunction with external
devices and components recommended or approved by Hirschmann.
The product can only be operated
correctly and safely if it is transported, stored, installed and assembled
properly and correctly. Furthermore,
it must be operated and serviced
carefully.
Safety Guidelines
Power Supply
䡺 Switch the basic devices on only when
the case is closed.
z
Warning!
The devices may only be connected
to the supply voltage shown on the
type plate.
The devices are designed for operation with a safety extra-low voltage.
Thus, they may only be connected
to the supply voltage connections
with PELV circuits or alternatively
SELV circuits with the voltage
restrictions in accordance with
IEC/EN 60950-1.
䡺 For the case where the module is operated with external power supply: Use only a
safety extra-low voltage in accordance with
IEC/EN 60950-1 to power the system.
䡺 First of all you connect the ground
connection, before you establish the further
connections. When you remove connections, you disconnect the ground connection last.
䡺 Relevant for North America:
The subject unit is to be suppplied by a
Class 2 power source complying with the
requirements of the National Electrical
Code, table 11(b).
䡺 Relevant for North America:
Power, input and output (I/O) wiring must
be in accordance with Class I, Division 2
wiring methods [Article 501-4(b) of the
National Electrical Code, NFPA 70] and in
accordance with the authority having jurisdiction.
Peripheral equipment must be suitable for
the location it is used in.
Use 60/75°C or 75°C copper(CU)wire only.
Safety Guidelines
Shielding Ground
䡺 Beware of possible short circuits when
connecting a cable section with conductive
shielding braiding.
Safety Guidelines Housing
z
Warning!
Only technicians authorized by
Hirschmann are permitted to open
the housing.
Note: The SPIDER is grounded via a pin of
the 3pin terminal block.
䡺 Make sure that the electrical installation
meets local or nationally applicable safety
regulations.
z
Warning!
The ventilation slits must not be
covered so as to ensure free air circulation.
The distance to the ventilation slots
on the top and the bottom of the
housing has to be a minimum of 10
cm.
The side distance of the SPIDER
4TX/1FX... and SPIDER 8TX... devices to neighbour devices has to be a
minimum of 2 cm if the ambient
temperature is higher than 50°C.
Never insert pointed objects (thin
screwdrivers, wires, etc.) into the
inside of the subrack! Failure to
observe this point may result in injuries caused by electric shocks.
Note: If installed in a living area or office
environment, the device must be operated
exclusively in switch cabinets with fire protection characteristics according to EN
60950-1.
Note: The housing has to be mounted in
upright position.
Safety Guidelines Environment
z
Warning!
The device may only be operated in
the listed ambient temperature
range at the listed relative air humidity (non-condensing).
䡺 The installation location is to be selected so as to ensure compliance with the climatic limits listed in the Technical Data.
䡺 To be used in an up to Pollution Degree
2 environment only (IEC 60664-1).
3
Based specifications and
standards:
The devices fulfil the following
specifications and standards:
– EN 61000-6-2:2001 Generic standards –
Immunity for industrial environments
– EN 55022:1998 + A1:2000 + A2:2003 –
Information technology equipment –
Radio disturbance characteristics
– EN 60950-1:2001 – Safety of Information
Technology Equipment (ITE)
– EN 61131-2:2003 – Programmable Control-
lers
– FCC 47 CFR Part 15:2004–
Code of Federal Regulations
– cUL 508:1998 – Underwriters Labratories
Inc. Safety for Industrial Control
Equipment.
Certified devices are marked with a
certification identifier.
7
Notes on CE
identification
The devices comply with the regulations of the following European
directive:
89/336/EEC
Council Directive on the harmonization of the legal regulations of member states on electromagnetic compatibility (amended by Directives
91/263/EEC, 92/31/EEC and
93/68/EEC).
SPIDER 5TX EEC:
72/245/EEC, 2005/83/EG
Radio interference (electromagnetic
compatibility) in vehicles
Certified devices are marked with a
e1 certification identifier.
The EU declaration of conformity is
kept available for the responsible
authorities in accordance with the
above-mentioned EU directives at:
Hirschmann
Automation and Control GmbH
Stuttgarter Straße 45-51
D-72654 Neckartenzlingen
Telefon ++49-(0)1805-14-1538
The product can be used in the residential sphere (residential sphere,
business and trade sphere and small
companies) and in the industrial
sphere.
– Interference immunity:
EN 61000-6-2:2001
– Radio interference level:
EN 55022:1998 + A1:2000
+ A2:2003, Class A
z
Warning!
This is a Class A device. This equipment may cause radio interference if
Staff qualification
requirements
Note: Qualified personnel, as understood
in this manual and in the warning signs, are
persons who are familiar with the setup,
assembly, startup, and operation of this
product and are appropriately qualified for
their job. This includes, for example, those
persons who have been:
– trained or directed or authorized to
switch on and off, to ground and to label
power circuits and devices or systems in
accordance with current safety engineering standards
– trained or directed in the care and use of
appropriate safety equipment in accordance with the current standards of safety
engineering
– trained in providing first aid.
General Safety Instructions
䡺 This device is electrically operated.
Adhere strictly to the safety requirements
relating to voltages applied to the device as
described in the operating instructions!
z
Warning!
Failure to observe the information
given in the warnings could result in
serious injury and/or major damage.
Only personnel that have received
appropriate training should operate
this device or work in its immediate
vicinity. The personnel must be fully
familiar with all of the warnings and
maintenance measures in these
operating instructions.
Correct transport, storage, and
assembly as well as careful operation and maintenance are essential in
ensuring safe and reliable operation
of this device.
Use only undamaged parts!
䡺 These products are only to be used in
the manner indicated in this version of the
”Description and Operating Instructions”.
䡺 Particular attention is to be paid to all
warnings and items of information relating
to safety.
z
Warning!
Any work that may have to be performed on the electrical installation
should be performed by fully qualified technicians only.
z
Warning!
(SPIDER 1TX/1FX...
SPIDER 4TX/1FX...)
LED- or LASER components according to IEC 60825-1 (2001):
CLASS 1 LASER PRODUCT.
LIGHT EMITTING DIODE - CLASS 1
LED PRODUCT.
used in a residential area; in this
case it is the operator´s responsibility to take appropriate measures.
The precondition for compliance
with EMC limit values is strict adherence to the construction guidelines
specified in this description and
operating instructions.
FCC Note:
This equipment has been tested and found
to comply with the limits for a Class A digital device, persuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction
manual, may cause harmful interference to
radio communications. Operation of this
equipment in a residential area is likely to
cause harmful interference in which case
the user will be required to correct the interference at his own expense.
,
Recycling Note:
After its use, this product has to be
processed as electronic scrap and
disposed of according to the prevailing waste disposal regulations of
your community / district / country /
state.
Loading...