Hirschmann OS20, OS30 User Manual
Installation OS20/OS30
Release 03 06/2015
Technical Support
https://hirschmann-support.belden.eu.com
User Manual
Installation
IP67 Switch
OS20 / OS30
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2015 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD/DVD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: +49 1805 141538
OS20/OS30 039 727-001-03-0615
1.7.15
Installation OS20/OS30
Release 03 06/2015
3
Contents
Safety instructions 5
About this Manual 9
Legend 9
1 Description 10
1.1 General device description 10
1.2 Device name and product code 11
1.3 Device views 13
1.3.1 Front view 13
1.3.2 Interfaces 13
1.4 Power supply 14
1.5 Ethernet ports 15
1.5.1 10/100 Mbit/s twisted pair port 15
1.5.2 100 Mbit/s F/O port 15
1.5.3 1000 Mbit/s F/O port 16
1.5.4 Pin assignments 16
1.6 Display elements 17
1.6.1 Device state 18
1.6.2 Port state 18
1.7 Management interfaces 19
1.7.1 V.24 interface (external management) 19
1.7.2 ACA interface (ACA21-M12) 20
1.8 “FAULT” signal contact 21
2 Installation 22
2.1 Checking the package contents 22
2.2 Installing and grounding the device 23
2.2.1 Mounting on a flat surface 23
2.2.2 Grounding the device 23
2.3 Wiring the connectors for supply voltage and signal contact 24
2.4 Operating the device 25
2.5 Connecting data cables 25
2.5.1 Twisted Pair ports 25
2.5.2 Optical fiber ports 25
3 Making basic settings 26
4
Installation OS20/OS30
Release 03 06/2015
4 Monitoring the ambient air temperature 27
5 Maintenance and service 28
6Disassembly 29
6.1 Removing the device 29
7 Technical data 30
A Further Support 37
Installation OS20/OS30
Release 03 06/2015
5
Safety instructions
General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a damaged
or malfunctioning the device, turn off the supply voltage and return the
device to Hirschmann for inspection.
Certified usage
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product only according to the technical specifications.
See “Technical data” on page 30.
Connect to the product only components suitable for the requirements
of the specific application case.
Device casing
Only technicians authorized by the manufacturer are permitted to open
the casing.
Never insert pointed objects (narrow screwdrivers, wires, etc.) into the
device or into the connection terminals for electric conductors. Do not
touch the connection terminals.
At ambient temperatures > 140 °F (60 °C):
The surfaces of the device housing may become hot. Avoid touching
the device while it is operating.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.
6
Installation OS20/OS30
Release 03 06/2015
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
Grounding the device
The device is grounded via the separate ground screw.
See figure 3 on page 14.
Use a wire diameter for the ground conductor that is no smaller than
the diameter of the supply voltage connection, however of at least
0.5 mm² (AWG20).
Ground the device before connecting any other cables.
Disconnect the grounding only after disconnecting all other cables.
Shielding ground
The overall shield of a connected shielded twisted-pair cable is connected
to the metal housing as a conductor.
Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.
Supply voltage
The devices are designed for operation with safety extra-low voltage.
Connect only SELV circuits with voltage restrictions in line with IEC/EN
60950-1 to the supply voltage connections and signal contacts.
The supply voltage is electrically isolated from the housing.
Use a power supply cable which is suitable for the voltage, the current
and the physical load.
Hirschmann recommends a wire diameter of 0.5 mm² to 0.75 mm²
(AWG20 to AWG18).
Installation OS20/OS30
Release 03 06/2015
7
Relevant for North America:
The device may only be connected to a Class 2 supply voltage that fulfills
the requirements of the National Electrical Code, Table 11(b). If the
voltage is being supplied redundantly (two different voltage sources), the
combined supply voltages must fulfill the requirements of the National
Electrical Code, Table 11(b).
Relevant for North America: For use in Class 2 circuits.
Only use copper wire/conductors of class 1, 75 °C (167 °F).
Relevant for installations under UL conditions:
Supply voltage: 19.2 V DC to 28.8 V DC
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
2004/108/EC (EMC)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic
compatibility.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: +49 1805 141538
The device can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55022
You find more information on technical standards here:
“Technical data” on page 30
The assembly guidelines provided in these instructions must be strictly
adhered to in order to observe the EMC threshold values.
8
Installation OS20/OS30
Release 03 06/2015
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.
LED or laser components
LED or LASER components according to IEC 60825-1 (2014):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT
FCC note:
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate these
frequencies. If it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a residential area can also cause interference, and in this
case the user is obliged to cover the costs of removing the interference.
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.
Installation OS20/OS30
Release 03 06/2015
9
About this Manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
The following manuals are available as PDF files on the CD/DVD supplied:
Installation user manual
Basic Configuration user manual
Redundancy Configuration user manual
User Manual Industry Protocols
Reference manual for the graphical user interface
Command Line Interface reference manual
The Industrial HiVision network management software provides you with
additional options for smooth configuration and monitoring:
ActiveX control for SCADA integration
Auto-topology discovery
Browser interface
Client/server structure
Event handling
Event log
Simultaneous configuration of multiple devices
Graphical user interface with network layout
SNMP/OPC gateway
Legend
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading
10
Installation OS20/OS30
Release 03 06/2015
1 Description
1.1 General device description
You can choose from between a wide range of variants. You have the option
to set up your device individually based on different criteria:
Number of ports
Transmission speed
Types of connectors
Temperature range
Supply voltage range
Certifications
The OS20-... device variants are IP67 Switches without gigabit Ethernet
ports and with ten 10/100 Mbit/s Ethernet ports.
The OS30-... device variants are IP67 Switches with two gigabit Ethernet
ports (1000 Mbit/s) and eight 10/100 Mbit/s Ethernet ports.
The OS20/OS30 devices are designed for the special requirements of
industrial automation. They meet the relevant industry standards, provide
very high operational reliability, even under extreme conditions, and also
long-term reliability and flexibility.
The devices allow you to set up switched and routed industrial Ethernet
networks that conform to the IEEE 802.3 standard.
The devices work without a fan.
You have the option of choosing various media to connect to the terminal
devices and other network components:
twisted pair cable
multimode F/O
singlemode F/O
The redundancy concept allows the network to be reconfigured quickly.
There are convenient options for managing the device. Administer your
devices via:
a Web browser
SSH
Telnet
HiDiscovery (Software for putting the device into operation)
network management software (e.g. Industrial HiVision)
a V.24 interface (locally on the device)
Installation OS20/OS30
Release 03 06/2015
11
The devices provide you with a large range of functions, which the manuals
for the operating software inform you about. You will find these manuals as
PDF files on the enclosed CD/DVD, or you can download them from the
Internet on the Hirschmann product pages (www.hirschmann.com).
The Hirschmann network components help you ensure continuous
communication across all levels of the company.
1.2 Device name and product code
The device name corresponds to the product code. The product code is
made up of characteristics with defined positions. The characteristic values
stand for specific product properties.
You have numerous options of combining the device characteristics. You can
determine the possible combinations using the configurator which is
available in the Belden E-Catalog (www.e-catalog.beldensolutions.com) on
the web page of the device.
Note: For the two uplink ports (product positions 12 to 13 and 14 to 15),
choose the same variant (either variant 1 or variant 4).
12
Installation OS20/OS30
Release 03 06/2015
Position Characteristic Characteri
stic value
Description
1 to 4 Product OS20 IP67 Switch without gigabit ports
OS30 IP67 Switch with gigabit ports
5 - (hyphen) 6 to 7 Number of special
ports
00 0 ×
8 to 9 Number of 100 Mbit/s
ports:
08 8 ×
10 10 ×
10 to 11 Number of
1000 Mbit/s ports
00 0 ×
02 2 ×
12 to 13 1. Uplink port
(medium/connector)
1M M-FAST SFP-MM / LC / EEC / variant 1
1S M-FAST SFP-SM / LC / EEC / variant 1
1P M-FAST SFP-SM+ / LC / EEC / variant 1
1L M-FAST SFP-LH / LC / EEC / variant 1
1A M-SFP-SX / LC / EEC / variant 1
1B M-SFP-LX / LC / EEC / variant 1
1C M-SFP-LH / LC / EEC / variant 1
1D M-SFP-LH+ / LC / EEC / variant 1
4M M-FAST SFP-MM / LC / EEC / variant 4
4S M-FAST SFP-SM / LC / EEC / variant 4
4P M-FAST SFP-SM+ / LC / EEC / variant 4
4L M-FAST SFP-LH / LC / EEC / variant 4
4A M-SFP-SX / LC / EEC / variant 4
4B M-SFP-LX / LC / EEC / variant 4
4C M-SFP-LH / LC / EEC / variant 4
4D M-SFP-LH+ / LC / EEC / variant 4
14 to 15 2. Uplink port
(medium/connector)
See positions 12 to 13
16 Temperature range T −40 °F ... +158 °F (−40 °C ... +70 °C )
17 Voltage range incl.
max. tolerances
R 16.8 VDC ... 45.0 VDC
18 Approvals E CE, C-Trick, E1, EN 50155, EN 50121-4
(railway, trackside), FCC
19 Software variant P Professional
Table 1: Combination options for the device variants of OS20/OS30
Loading...