Hirschmann OCTOPUS OS3 User Manual

Installation OCTOPUS OS3

Release 01 02/2019

Technical support

https://hirschmann-support.belden.com

User Manual

Installation

Managed Ethernet Switch
OCTOPUS OS3

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.

© 2019 Hirschmann Automation and Control GmbH

Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use.

The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).

Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany

8.2.19

Installation OCTOPUS OS3

Release 01 02/2019

3

Contents

Safety instructions 5

About this manual 10

Key 11

1 Description 12

1.1 General device description 12

1.2 Device name and product code 12

1.3 Device views 14

1.3.1 Front view 14

1.4 Power supply 15

1.4.1 Supply voltage with the characteristic value N9 15

1.5 Ethernet ports 15

1.6 Pin assignments 16

1.7 Display elements 17

1.7.1 Device state 17

1.7.2 Port Status 19

1.8 Management interfaces 20

1.8.1 V.24 interface (external management) 20

1.8.2 USB interface 20

1.9 Input/output interfaces 21

1.9.1 Signal contact 21

2 Installation 22

2.1 Checking the package contents 22

2.2 Installing and grounding the device 23

2.2.1 Mounting on a flat surface 23

2.2.2 Grounding the device 24

2.3 Connecting the supply voltage 25

2.4 Connecting data cables 26

3 Basic Settings 27

4 Monitoring the ambient air temperature 28

5 Maintenance and service 29

4

Installation OCTOPUS OS3

Release 01 02/2019

6Disassembly 30

6.1 Removing the device 30

7 Technical data 31

7.1 General data 31

7.2 Supply voltage 31

7.3 Signal contact 32

7.4 Power consumption/power output 32

7.5 Climatic conditions during operation 33

7.6 Climatic conditions during storage 33

7.7 Dimension drawings 34

7.8 EMC and immunity 35

7.9 Network range 38

8 Scope of delivery, order numbers and

accessories 39

8.1 Scope of delivery 39

8.2 Accessories 39

9 Underlying technical standards 40

A Further support 41

Installation OCTOPUS OS3

Release 01 02/2019

5

Safety instructions

 General safety instructions

You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
 Before connecting any cable, read this document, and the safety

instructions and warnings.

 Operate the device with undamaged components exclusively.
 The device is free of any service components. In case of a damaged

or malfunctioning device, turn off the supply voltage and return the
device to Hirschmann for inspection.

 National and international safety regulations

 Verify that the electrical installation meets local or nationally applicable

safety regulations.

 Certified usage

 Use the product only for the application cases described in the

Hirschmann product information, including this manual.

 Operate the product only according to the technical specifications.

See “Technical data” on page 31.

 Connect to the product only components suitable for the requirements

of the specific application case.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,
or equipment damage.

6

Installation OCTOPUS OS3

Release 01 02/2019

 Qualification requirements for personnel

 Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

 Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.

 Qualified personnel are aware of the dangers that exist in their work.
 Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

 Qualified personnel receive training on a regular basis.

 Installation site requirements

 Verify that there is at least 4 in (10 cm) of space above and below the

device.

 Install this device solely in an operating site with restricted access, to

which maintenance staff have exclusive access. Install the device in
such a way that it is protected against mechanical forces in the area of
the power supply.

 Device casing

Only technicians authorized by the manufacturer are permitted to open
the casing.
 Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not
touch the connection terminals.

 Keep the cooling fins free to ensure good air circulation.
 The surfaces of the device housing may become hot. Avoid touching

the device while it is operating.

 To preserve the suitability of your device for IP54, seal all unused

connections and ports with the provided plastic protection screws. See

“Scope of delivery” on page 39. See “Scope of delivery” on page 39 in

case of an additional demand.
To preserve the IP54 suitability for your device, exclusively connect
components with degree of protection IP54.

 For operation according to EN 45545: Seal all unused connections

and ports exclusively with metal protection screws and metal screw
caps. The use of plastic protection screws is prohibited.
Protection screws and screw caps made of metal are available as an
accessory.

See “Accessories” on page 39.

Installation OCTOPUS OS3

Release 01 02/2019

7

 Grounding the device

Grounding the device is by means of a separate ground connection on the
device.

 Ground the device before connecting any other cables.
 Disconnect the grounding only after disconnecting all other cables.

The overall shield of a connected shielded twisted pair cable is connected
to the grounding connector on the front panel as a conductor.

 Requirements for connecting electrical wires

Before connecting the electrical wires, always verify that the
requirements listed are complied with.

General requirements for connecting electrical wires
The following requirements apply without restrictions:

 The electrical wires are voltage-free.
 The cables used are permitted for the temperature range of the application case.
 Relevant for North America:

Exclusively use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire.

Requirements for connecting the signal contact
The following requirements apply without restrictions:

 The connected voltage complies with the requirements for a safety extra-low voltage

(SELV) or ES1 as per IEC/EN 62368-1.

 The connected voltage is limited by a current limitation device or a fuse.

Observe the electrical threshold values for the signal contact.

See “General data” on page 31.

Requirements for connecting the supply voltage
The following requirements apply without restrictions:
All of the following requirements are complied with:

 The supply voltage corresponds to the voltage specified on the type plate of the device.
 The power supply conforms to overvoltage category I or II.
 The power supply has an easily accessible disconnecting device (for example a switch or

a plug). This disconnecting device is clearly identified. So in the case of an emergency, it is
clear which disconnecting device belongs to which power supply cable.

 The wire diameter of the power supply cable is at least 1 mm² (North America: AWG16) on

the supply voltage input.

The following requirements apply alternatively:

Relevant when the device is supplied via 1 voltage input:
Relevant for North America:

The power supply complies with the requirements according to NEC Class 2.

8

Installation OCTOPUS OS3

Release 01 02/2019

 CE marking

The labeled devices comply with the regulations contained in the following
European directive(s):

2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.

2014/30/EU (EMC)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic
compatibility.

In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:

Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
www.hirschmann.com

The device can be used in the industrial sector.

 Interference immunity: EN 61000-6-2
 Emitted interference: EN 55032
 Safety: EN 62368-1

You find more information on technical standards here:

See “Technical data” on page 31.

Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.

Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.

Installation OCTOPUS OS3

Release 01 02/2019

9

 FCC note:

This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate these
frequencies. If it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a residential area can also cause interference, and in this
case the user is obliged to cover the costs of removing the interference.

 Recycling note

After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

10

Installation OCTOPUS OS3

Release 01 02/2019

About this manual

The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
The following manuals are available on the Internet at https://

www.doc.hirschmann.com/ as downloads:

 User Manual Installation
 User Manual Basic Configuration
 User Manual Redundancy Configuration
 Reference Manual Graphical User Interface
 Reference Manual Command Line Interface

Installation OCTOPUS OS3

Release 01 02/2019

11

Key

The symbols used in this manual have the following meanings:

 Listing

 Work step



Subheading

12

Installation OCTOPUS OS3

Release 01 02/2019

1 Description

1.1 General device description

The device is designed for the special requirements of industrial automation.
The device meets the relevant industry standards, provides very high
operational reliability, even under extreme conditions, and also long-term
reliability and flexibility.

The devices allow you to set up switched industrial Ethernet networks that
conform to the IEEE 802.3 standard.
The devices work without a fan.

The devices provide you with a large range of functions, which the manuals
for the operating software inform you about. You find these manuals as PDF
files on the Internet at: https://www.doc.hirschmann.com
The Hirschmann network components help you ensure continuous
communication across all levels of the company.
The Network Management Software Industrial HiVision provides you with
options for smooth configuration and monitoring. You find further information
on the Internet at the Hirschmann product pages: http://

www.hirschmann.com/en/QR/INET-Industrial-HiVision

There are convenient options for managing the device. Manage your devices
via:

 Network management software (for example Industrial HiVision)
 Web browser
 V.24 interface (locally on the device)
 SSH
 Telnet

1.2 Device name and product code

The product code is made up of characteristics with defined positions. The
characteristic values stand for specific product properties.

Item Characteristic Characteri

stic value

Description

1 ... 3 Product OCTOPUS

OS3

OCTOPUS 24GE-HV-Trainrouter

4 (hyphen) -

Table 1: Device name and product code

Installation OCTOPUS OS3

Release 01 02/2019

13

5 Data rate 4 10a/100/1000 Mbit/s
6 Hardware type 0 Standard
7 (hyphen) ­8 ... 9 Number:

PoE ports
PoE(+) ports

00 0 ×

10 ... 11 Number:

10

a

/100 Mbit/s PoE/

PoE+ ports

00 0 × 10

a

/100 Mbit/s PoE/PoE+ ports

12 ... 13 Number:

10

a

/100/1000 Mbit/s

PoE/PoE+ ports

00 0 × 10

a

/100/1000 Mbit/s PoE/PoE+ ports

14 ... 15 Number:

10

a

/100 Mbit/s ports

00 0 × 10

a

/100 Mbit/s ports

16 ... 17 Number:

10

a

/100/1000 Mbit/s

ports

24 24 × 10

a

/100/1000 Mbit/s ports

18 ... 19 Number:

Ports >1000 Mbit/s

00 0 × 10000 Mbit/s ports

20 ... 21 First uplink port pair T6 Standard
22 ... 23 Second uplink port

pair

T6 Standard

24 (hyphen) ­25 Temperature range T Extended -40 °F ... +158 °F (-

40 °C ... +70 °C)

26 ... 27 Supply voltage N9 Rated voltage 72 V DC ... 110 V DC

Rated voltage range 50.4 V DC ... 138 V DC
Connection type 5-pin M12 connector

28 ... 29 Certificates and

declarations

S9 Z9 + EN 50121-4 + EN 50155

30 ... 31 Software packages MR Unicast + Multicast Routing
32 ... 33 Customer-specific

version

HH Hirschmann standard

34 Hardware

configuration

S Standard

35 Software configuration E Entry (Hirschmann Standard)
36 ... 37 Software level 3A HiOS Layer 3 Advanced
38 ... 42 Software version 07.5. Software version 07.5.

XX.X Current software version
43 ... 44 Maintenance version XX Current maintenance version
45 ... 47 Place of manufacture -NT Manufactured in Germany

a. Exclusively for twisted pair connections.

Item Characteristic Characteri

stic value

Description

Table 1: Device name and product code

14

Installation OCTOPUS OS3

Release 01 02/2019

1.3 Device views

1.3.1 Front view

1 V.24 interface 4-pin, “A”-coded M12 socket
2 USB interface 5-pin, “A”-coded M12 socket
3 Signal contact 5-pin, “A”-coded M12 plug
4 Supply voltage connection 5-pin, “K”-coded M12 plug
5 24 × 10/100/1000 Mbit/s twisted pair port 8-pin, “X”-coded M12 socket
6 LED display elements for port status
7 Slot hole for mounting on a flat surface
8 LED display elements for device status
9 Ground connection

Table 2: Front view (using the example OCTOPUS3-40-...)

1 2 3 4 5 6

9

8 7

Installation OCTOPUS OS3

Release 01 02/2019

15

1.4 Power supply

1.4.1 Supply voltage with the characteristic value N9

The power is supplied via a “K”-coded M12 plug.
For information about the position on the device see chapter “Device views”

on page 14.

Further information:

See “Device name and product code” on page 12.

1.5 Ethernet ports

You have the option to connect end devices or other segments to the ports
of the device via twisted pair cables.
You find information on pin assignments for making patch cables here:

“Pin assignments” on page 16

 10/100/1000 Mbit/s twisted pair port

This port is an 8-pin, “X”-coded M12 socket.
The 10/100/1000 Mbit/s twisted pair port allows you to connect network
components according to the IEEE 802.3 10BASE-T/100BASE-TX/
1000BASE-T standard.
This port supports:

 10 Mbit/s half-duplex mode, 10 Mbit/s full duplex mode
 100 Mbit/s half-duplex mode, 100 Mbit/s full duplex mode
 1000 Mbit/s full duplex
 Autocrossing (if autonegotiation is activated)
 Autonegotiation
 Autopolarity

The port casing is electrically connected to the front panel.
The pin assignment corresponds to MDI-X.

16

Installation OCTOPUS OS3

Release 01 02/2019

1.6 Pin assignments

Figure 1: Pin assignments: Interfaces and ports

Pin

1 TX
2 RX
3 ­4 GND

Function

1

2

3

4

V24

1 Uin
2 ­3 D ­4 GND
5 D+

Pin Function

1

2

3

4

5

ACA

FunctionPin

1 P+
2
3 P ­4
5 PE

Do not use

Do not use

1

2

3

4

5

Power

1

2

3

4

5

Signal

FunctionPin

1 Bl_DB+
2 Bl_DB ­3 Bl_DA+
4 Bl_DA ­5 Bl_DC+
6 Bl_DC ­7 Bl_DD ­8 Bl_DD+

1

2

7

4

3

5

6

8

Port GE

FunctionPin

1 ­2
3
4 ­5

Installation OCTOPUS OS3

Release 01 02/2019

17

1.7 Display elements

After the supply voltage is set up, the Software starts and initializes the
device. Afterwards, the device performs a self-test. During this process,
various LEDs light up.

1.7.1 Device state

These LEDs provide information about conditions which affect the operation
of the whole device.

Figure 2: Device status: location of the display elements on the device (front side of

the device)

LED Display Color Activity Meaning

Power Supply voltage — none Supply voltage is too low

yellow lights up Device variants with redundant power

supply:
Supply voltage 1 or 2 is on

flashes 4 times
a period

Software update is running. Maintain the
power supply.

green lights up Device variants with redundant power

supply:
Supply voltage 1 and 2 is on

Device variants with single power supply:
Supply voltage is on

Table 3: Device Status

Status

RM

Power

ACA

18

Installation OCTOPUS OS3

Release 01 02/2019

Status Device Status — none Device is starting and/or is not ready for

operation.

green lights up Device is ready for operation.

Characteristics can be configured

red lights up Device is ready for operation.

Device has detected at least one error in the
monitoring results

flashes 1 time
a period

The boot parameters used when the device
has been started differ from the boot
parameters saved.
Start the device again.

flashes 4 times
a period

Device has detected a multiple IP address

RM Ring Manager — none No redundancy configured

green lights up Redundancy exists

flashes 1 time
a period

Device is reporting an incorrect
configuration of the RM function

yellow lights up No redundancy exists

ACA Storage medium

ACA

— none ACA storage medium not connected
green lights up ACA storage medium connected

flashes 3 times
a period

Device writes to/reads from the storage
medium

yellow lights up ACA storage medium inoperative

LED Display Color Activity Meaning

Table 3: Device Status

Installation OCTOPUS OS3

Release 01 02/2019

19

1.7.2 Port Status

Note: In the present hardware version, the right side port LEDs of the M12
ports are without function. The port status is displayed via the left side port
LED.

Figure 3: Port status: location of the display elements on the device (front side of

the device)

LED Display Color Activity Meaning

L/D Link status — none Device detects an invalid or missing link

green lights up Device detects a valid link

flashes 1
time a period

Port is switched to stand-by

flashes 3
times a
period

Port is switched off

yellow lights up Device detects a non-supported SFP transceiver or

a non-supported data rate
flashing Device is transmitting and/or receiving data
flashes 1

time a period

Device detects at least one unauthorized MAC

address (Port Security Violation)

Table 4: Port status

20

Installation OCTOPUS OS3

Release 01 02/2019

1.8 Management interfaces

1.8.1 V.24 interface (external management)

This interface is a 4-pin, “A”-coded M12 socket.
The V.24 interface is a serial interface for the local connection of an external
management station (VT100 terminal or PC with corresponding terminal
emulation). This allows you to set up a connection to the Command Line
Interface (CLI) and to the system monitor.

The socket housing is electrically connected to the front panel of the device.
The V.24 interface is electrically insulated from the supply voltage.

1.8.2 USB interface

This interface is a 5-pin, “A”-coded M12 socket with shielding.
The USB interface allows you to connect the AutoConfiguration Adapter
ACA21-M12/ACA22-M12 storage medium. This is used for saving/loading
the configuration data and diagnostic information, and for loading the
software.

The USB interface has the following properties:

 Supplies current of max. 500 mA
 Voltage not potential-separated
 Supports the USB master mode
 Supports USB 2.0

VT100 terminal settings

Speed 9600 Baud
Data 8 bit
Stopbit 1 bit
Handshake off
Parity none

Installation OCTOPUS OS3

Release 01 02/2019

21

1.9 Input/output interfaces

1.9.1 Signal contact

This interface is a 5-pin, “A”-coded M12 plug.
The signal contact is a potential-free relay contact. The signal contact is open
when the device is not connected to a power supply.
The signal contact allows you to control external devices or monitor device
functions.
In the configuration, you specify how the device uses the signal contact.
You find detailed information regarding possible applications and
configuration of the signal contact in the software user documentation. You
find the software user documentation as PDF files on the Internet at: https://

www.doc.hirschmann.com

22

Installation OCTOPUS OS3

Release 01 02/2019

2 Installation

The devices have been developed for practical application in a harsh
industrial environment.
Hirschmann supplies the device ready for operation.

Perform the following steps to install and configure the device:

 Checking the package contents
 Installing and grounding the device
 Connecting the supply voltage
 Connecting data cables

2.1 Checking the package contents

 Check whether the package includes all items named in the section

“Scope of delivery” on page 39.

 Check the individual parts for transport damage.

Installation OCTOPUS OS3

Release 01 02/2019

23

2.2 Installing and grounding the device

 When you are selecting the installation location, make sure you observe

the climatic threshold values specified in the technical data.
Prevent heat from the surroundings from affecting the device.

 Verify that there is at least 4 in (10 cm) of space above and below the

device.

 Remove the provided transport protection caps and the transport

protection screws from the device.

2.2.1 Mounting on a flat surface

Proceed as follows:
 You will find the drilling dimensions for mounting the device in the chapter

“Dimension drawings” on page 34.

 Install the device with screws on the flat surface.

Completely screw the device to the flat surface using screws through
each mounting hole. Exclusively use screws suitable for the installation
and application case to ensure flawless operation of the device.

CAUTION

BURNING HAZARD

The surfaces of the device casing may become hot. Avoid touching the
device while it is operating.
If ambient temperatures are ≥113 °F (≥45 °C), exclusively install the device
in “restricted access locations” according to EN 62368.

Failure to follow these instructions can result in injury or equipment
damage.

24

Installation OCTOPUS OS3

Release 01 02/2019

2.2.2 Grounding the device

Figure 4: Grounding: location of ground connections on the device (left side of the

device)

For the position of the ground connection on the device see figure 4.
 Ground the device via 1 ground connection using a ground connection

screw.
You find the prescribed tightening torque in chapter:

“General data” on page 31

WARNING

ELECTRIC SHOCK

Ground the device before connecting any other cables.

Failure to follow these instructions can result in death, serious injury,
or equipment damage.

Installation OCTOPUS OS3

Release 01 02/2019

25

2.3 Connecting the supply voltage

 Mount the power supply cable to the power supply connector of the

device.
You find the prescribed tightening torque in chapter:

“General data” on page 31

 Enable the supply voltage.

WARNING

ELECTRIC SHOCK

Connect only a supply voltage that corresponds to the type plate of your
device.

Failure to follow these instructions can result in death, serious injury,
or equipment damage.

26

Installation OCTOPUS OS3

Release 01 02/2019

2.4 Connecting data cables

Note the following general recommendations for data cable connections in
environments with high electrical interference levels:

 Keep the length of the data cables as short as possible.
 Use optical data cables for the data transmission between the buildings.
 When using copper cables, provide a sufficient separation between the

power supply cables and the data cables. Ideally, install the cables in
separate cable channels.

 Verify that power supply cables and data cables do not run parallel over

longer distances. If reducing the inductive coupling is necessary, verify
that the power supply cables and data cables cross at a 90° angle.

 Use SF/UTP cables as per ISO/IEC 11801:2002.
 Connect the data cables according to your requirements.
 Seal all unused connections and ports with protection screws.

Note: To preserve the suitability of your device for IP54, seal all unused
connections and ports with the provided plastic protection screws. See

“Scope of delivery” on page 39. See “Scope of delivery” on page 39 in case

of an additional demand.
To preserve the IP54 suitability for your device, exclusively connect
components with degree of protection IP54.

Note: For operation according to EN 45545: Seal all unused connections
and ports exclusively with metal protection screws and metal screw caps.
The use of plastic protection screws is prohibited.
Protection screws and screw caps made of metal are available as an
accessory.

See “Accessories” on page 39.

Installation OCTOPUS OS3

Release 01 02/2019

27

3 Basic Settings

The IP parameters must be entered when the device is installed for the first
time. The device provides the following options for configuring IP addresses:

 AutoConfiguration Adapter
 Input via the HiView or Industrial HiVision application. You find further

information about the applications HiView or Industrial HiVision on the
Internet at the Hirschmann product pages:

HiView

http://www.hirschmann.com/en/QR/INET-HiView

Industrial HiVision

http://www.hirschmann.com/en/QR/INET-Industrial-HiVision

 Input via the V.24 interface
 Configuration via BOOTP
 Configuration via DHCP (Option 82)

You will find more information in the “Basic Configuration User Manual”.

 Default settings

 Ethernet ports: link status is not evaluated (signal contact)
 IP address: The device looks for the IP address using DHCP
 Optical ports: Full duplex

TP ports: Autonegotiation

 Management password:

user, password: public (read only)
admin, password: private (read/write)

 Rapid Spanning Tree Protocol: activated
 V.24 data rate: 9600 Baud

CAUTION

DAMAGE TO THE USB INTERFACE

Exclusively use a Hirschmann AutoConfiguration Adapter (ACA) to
configure the device via the USB interface. Other connectors may cause
damage to the interface or result in a faulty configuration.

Failure to follow these instructions can result in minor injury or
equipment damage.

28

Installation OCTOPUS OS3

Release 01 02/2019

4 Monitoring the ambient air temperature

Operate the device below the specified maximum ambient air temperature
exclusively.

See “General data” on page 31.

The ambient air temperature is the temperature of the air at a distance of 2 in
(5 cm) from the device. It depends on the installation conditions of the device,
for example the distance from other devices or other objects, and the output
of neighboring devices.

The temperature displayed in the CLI and the GUI is the internal temperature
of the device. It is higher than the ambient air temperature. The maximum
internal temperature of the device named in the technical data is a guideline
that indicates to you that the maximum ambient air temperature has possibly
been exceeded.

Installation OCTOPUS OS3

Release 01 02/2019

29

5 Maintenance and service

 When designing this device, Hirschmann largely avoided using high-wear

parts. The parts subject to wear and tear are dimensioned to last longer
than the lifetime of the product when it is operated normally. Operate this
device according to the specifications.

 Relays are subject to natural wear. This wear depends on the frequency

of the switching operations. Check the resistance of the closed relay
contacts and the switching function depending on the frequency of the
switching operations.

 Hirschmann is continually working on improving and developing their

software. Check regularly whether there is an updated version of the
software that provides you with additional benefits. You find information
and software downloads on the Hirschmann product pages on the
Internet (http://www.hirschmann.com).

 Depending on the pollution degree of the operating environment, check

regularly whether the cooling finds and surfaces of the device are freely
accessible.

 Internal fuses are triggered only in the case of a detected error in the

device. In case of damage or malfunction of the device, turn off the supply
voltage and return the device to the plant for inspection.

Note: You find information on settling complaints on the Internet at http://

www.beldensolutions.com/en/Service/Repairs/index.phtml.

30

Installation OCTOPUS OS3

Release 01 02/2019

6 Disassembly

6.1 Removing the device

Proceed as follows:

 Disable the supply voltage.
 Disconnect the data cables.
 Disconnect the power supply cable.
 Disconnect the grounding.
 Remove the screws.

WARNING

ELECTRIC SHOCK

Disconnect the grounding only after disconnecting all other cables.

Failure to follow these instructions can result in death, serious injury,
or equipment damage.

Installation OCTOPUS OS3

Release 01 02/2019

31

7 Technical data

7.1 General data

7.2 Supply voltage

OCTOPUS OS3

Dimensions
W × H × D

See “Dimension drawings” on page 34.

Weight 17.42 lb (7.9 kg)
Mounting See “Mounting on a flat surface” on page 23.
Pollution degree 2
Degree of protection IP54

Table 5: General data: OCTOPUS OS3

Supply voltage with the characteristic value N9

Rated voltage 72 V DC ... 110 V DC
Voltage range incl. maximum tolerances 50.4 V DC ... 138 V DC
Connection type 5-pin, “K”-coded M12 plug

Tightening torque 4.5 lb-in (0.51 Nm)
min. conductor diameter AWG18 (0.75 mm²)

max. conductor diameter AWG16 (1.5 mm²)
Power loss buffer > 10 ms
Overload current protection on the device Non-replaceable fuse
Back-up fuse for each voltage input Nominal rating: max. 20 A

Characteristic: slow blow
Peak inrush current 1 A
Connection for protective grounding See “Grounding the device” on page 24.
Current integral I²t 0.7 A²s

Table 6: Supply voltage with characteristic value N9

32

Installation OCTOPUS OS3

Release 01 02/2019

7.3 Signal contact

7.4 Power consumption/power output

Signal contact

Connection type 5-pin, “A”-coded M12 plug

Tightening torque 4.5 lb-in (0.51 Nm)

Nominal value I

max

=1A at U

max

=30VAC

I

max

=1A at U

max

=60VDC

Table 7: Signal contact

Device name Maximum power consumption Maximum power output

OCTOPUS 24GE-HV­Trainrouter

32 W 110 Btu (IT)/h

Table 8: Power consumption/power output

Installation OCTOPUS OS3

Release 01 02/2019

33

7.5 Climatic conditions during operation

7.6 Climatic conditions during storage

Climatic conditions during operation

Minimum clearance around the device Top and bottom device side: 3.94 in (10 cm)
Ambient air temperature

a

a. Temperature of the ambient air at a distance of 2 in (5 cm) from the device

Standard -40 °F ... +140 °F

(-40 °C ... +60 °C)

Extended -40 °F ... +158 °F

(-40 °C ... +70 °C)

Humidity (also in condensing

atmospheres)

10 % ... 95 %

Air pressure min. 700 hPa

(+9842 ft; +3000 m)
max. 1060 hPa
(-1312 ft; -400 m)

Table 9: Climatic conditions during operation

Climatic conditions during storage

Ambient air temperature

a

a. Temperature of the ambient air at a distance of 2 in (5 cm) from the device

Standard -40 °F ... +185 °F

(-40 °C ... +85 °C)

Extended -40 °F ... +185 °F

(-40 °C ... +85 °C)

Humidity (also in condensing

atmospheres)

10 % ... 95 %

Air pressure min. 600 hPa

(+13123 ft; +4000 m)
max. 1060 hPa
(-1312 ft; -400 m)

Table 10: Climatic conditions during storage

34

Installation OCTOPUS OS3

Release 01 02/2019

7.7 Dimension drawings

Figure 5: Dimension drawings

R 2,5

R 0.09

475

18.7

mm

in

189

7.44

200

7.87

77,5

3.05

77,5

3.05

77,5

3.05

77,5

3.05

90

3.54

72,5

2.86

8

0.31

137,5

5.41

48,5

1.91

Installation OCTOPUS OS3

Release

01

02/2019

35

7.8 EMC and immunity

Stability Standard applications

a

a. EN 61131-2, CE, FCC – applies to all devices

Railway applications
(trackside)

b

b. According to EN 50121-4.

Railway applications
(on vehicles)

c

c. According to EN 50155.

IEC 60068-2-6, test Fc Vibration TBD TBD TBD
IEC 60068-2-27, test Ea Shock TBD TBD TBD

Table 11: Immunity

36

Installation OCTOPUS OS3

Release

01

02/2019

EMC interference
emission

Standard applications

a

a. EN 61131-2, CE, FCC – applies to all devices

Railway applications
(trackside)

b

b. According to EN 50121-4.

Railway applications
(on vehicles)

c

c. According to EN 50155.

Radiated emission

EN 55032 Class A Class A Class A
FCC 47 CFR Part 15 Class A Class A Class A
EN 61000-6-4 Fulfilled Fulfilled Fulfilled

Conducted emission

EN 55032 AC and DC supply connections Class A Class A Class A
FCC 47 CFR Part 15 AC and DC supply connections Class A Class A Class A
EN 61000-6-4 AC and DC supply connections Fulfilled Fulfilled Fulfilled
EN 55032 Telecommunication connections Class A Class A Class A
EN 61000-6-4 Telecommunication connections Fulfilled Fulfilled Fulfilled

Table 12: EMC interference emission

EMC interference
immunity

Standard applications

a

Railway applications
(trackside)

b

Railway applications
(on vehicles)

c

Electrostatic discharge

EN 61000-4-2 Contact discharge ±4 kV ±6 kV ±6 kV
EN 61000-4-2 Air discharge ±8 kV ±8 kV ±8 kV

Electromagnetic field

EN 61000-4-3 80 MHz ... 3000 MHz max. 10 V/m max. 10 V/m max. 10 V/m
EN 61000-4-3 80 MHz ... 2700 MHz —

Fast transients (burst)

EN 61000-4-4 AC/DC supply connection ±2 kV ±4 kV
EN 61000-4-4 Data line ±4 kV ±4 kV

Table 13: EMC interference immunity

Installation OCTOPUS OS3

Release

01

02/2019

37

Voltage surges - DC supply connection

EN 61000-4-5 line/ground ±2 kV ±2 kV
EN 61000-4-5 line/line ±1 kV ±1 kV

Voltage surges - AC supply connection

EN 61000-4-5 line/ground ±2 kV ±2 kV
EN 61000-4-5 line/line ±1 kV ±1 kV

Voltage surges - data line

EN 61000-4-5 line/ground ±1 kV ±2 kV

Conducted disturbances

EN 61000-4-6 150 kHz ... 80 MHz 10 V 10 V

Damped oscillation - AC/DC supply connection

EN 61000-4-12 line/ground — —
EN 61000-4-12 line/line — —

Damped oscillation – data line

EN 61000-4-12 line/ground — — —
EN 61000-4-12 line/line — — —

Pulse magnetic field

EN 61000-4-9 — — —

a. EN 61131-2, CE, FCC – applies to all devices
b. According to EN 50121-4.
c. According to EN 50155.

EMC interference
immunity

Standard applications

a

Railway applications
(trackside)

b

Railway applications
(on vehicles)

c

Table 13: EMC interference immunity

38

Installation OCTOPUS OS3

Release

01

02/2019

7.9 Network range

10/100/1000 Mbit/s twisted pair port

Length of a twisted pair segment max. 328 ft (100 m) (for Cat5e cable)

Table 14: Network range: 10/100/1000 Mbit/s twisted pair port

Installation OCTOPUS OS3

Release 01 02/2019

39

8 Scope of delivery, order numbers and

accessories

8.1 Scope of delivery

8.2 Accessories

Note: Some products recommended as accessories do not support the
entire temperature range specified for the device and can thus restrict the
possible range of usage for the overall system.

Number Article

1 × Device
1 × General safety instructions
1 × Field attachable connector for the power supply, M12, “K”-coded
2 × Protection screw for M12 plug, plastic
26 × Protection screw for M12 socket, plastic

Designation Order number

AutoConfiguration Adapter ACA22-M12 (EEC) 942 125-001
Protection screw for M12 socket, metal, IP65/67 (25 pieces) 942 057-001
Protection screw for M12 socket, plastic, IP65/67 (25 pieces) 942 057-002
Protection screw for M12 plug, metal, IP65/67 (10 pieces) 942 115-001
Network management software Industrial HiVision 943 156-xxx

40

Installation OCTOPUS OS3

Release 01 02/2019

9 Underlying technical standards

The device has an approval based on a specific standard exclusively if the
approval indicator appears on the device casing.
The device generally fulfills the technical standards named in their current
versions.

Designation

EN 50121-4 Railway applications – EMC – Emission and immunity of the signaling

and telecommunications apparatus (Rail Trackside)

EN 55032 Electromagnetic compatibility of multimedia equipment – Emission

Requirements

EN 62368-1 Information technology equipment – Safety – Part 1: General

requirements

EN 61000-6-2 Electromagnetic compatibility (EMC) – Part 6-2: Generic standards –

Immunity for industrial environments
EN 61131-2 Programmable controllers – Part 2: Equipment requirements and tests
FCC 47 CFR Part 15 Code of Federal Regulations
IEEE 802.1AB Station and Media Access Control Connectivity Discovery
IEEE 802.1D Media Access Control Bridges
IEEE 802.1Q Virtual Bridged Local Area Networks
IEEE 802.3 Ethernet
UL 61010-1/-2-201 Safety for Industrial Control Equipment

Table 15: List of norms and standards

Installation OCTOPUS OS3

Release 01 02/2019

41

A Further support

Technical questions

For technical questions, please contact any Hirschmann dealer in your area
or Hirschmann directly.

You find the addresses of our partners on the Internet at http://

www.hirschmann.com.

A list of local telephone numbers and email addresses for technical support
directly from Hirschmann is available at https://

hirschmann-support.belden.com.

This site also includes a free of charge knowledge base and a software
download section.

Hirschmann Competence Center

The Hirschmann Competence Center is ahead of its competitors on three
counts with its complete range of innovative services:

 Consulting incorporates comprehensive technical advice, from system

evaluation through network planning to project planning.

 Training offers you an introduction to the basics, product briefing and user

training with certification.
You find the training courses on technology and products currently
available at http://www.hicomcenter.com.

 Support ranges from the first installation through the standby service to

maintenance concepts.

With the Hirschmann Competence Center, you decided against making any
compromises. Our client-customized package leaves you free to choose the
service components you want to use.

Internet:

http://www.hicomcenter.com