Hirschmann MACH104-16TX-PoEP-E-L2P, MACH104-16TX-PoEP-R-L2P, MACH104-16TX-PoEP-L2P, MACH104-16TX-PoEP+2X-L2P, MACH104-16TX-PoEP+2X-R-L2P User Manual

Installation MACH104

Release 08 01/2019

Technical support

https://hirschmann-support.belden.com

User Manual

Installation
Industrial Ethernet Workgroup Switch

MACH104 Full Gigabit Family

MACH104-20TX-F-4PoE...

MACH104-20TX-F...

MACH104-20TX-FR...

V.24USB

Aufkleber MAC-Adresse

P

FAULT

FAULT

Sb

RM

5

6

7

8

13

24

911

10 12

13 15

14 16

17 19

18 20

21 23

22 24

MACH104-20TX-F

V.24USB

Aufkleber MAC-Adresse

P

FAULT

FAULT

Sb

RM

5

6

7

8

13

24

911

10 12

13 15

14 16

17 19

18 20

21 23

22 24

MACH104-20TX-FR

V.24USB

Aufkleber MAC-Adresse

P

FAULT

FAULT

Sb

RM

5

6

7

8

13

24

911

10 12

13 15

14 16

17 19

18 20

21 23

22 24

MACH104-20TX-F-4PoE

P

2019-01-21

Installation MACH104

Release 08 01/2019

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.

© 2019 Hirschmann Automation and Control GmbH

Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use.

The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).

Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany

Installation MACH104

Release 08 01/2019

3

Contents

Safety instructions 5

About this manual 13

Legend 14

1 Description 15

1.1 General device description 15

1.2 Description of the device variants 16

1.2.1 MACH104-20TX-F...: Devices with 24 GB ports 16

1.2.2 MACH104-20TX-FR...: Devices with 24 GB ports and
redundant power supply 17

1.2.3 MACH104-20TX-F-4-PoE...: Devices with 24 GB
ports, 4 of them PoE ports 18

1.3 Supply voltage 19

1.3.1 MACH104-20TX-F... 19

1.3.2 MACH104-20TX-FR... 19

1.3.3 MACH104-20TX-F-4-PoE... 20

1.4 Ethernet ports 20

1.4.1 10/100/1000 Mbit/s twisted pair port 20

1.4.2 100 Mbit/s F/O port 21

1.4.3 1000 Mbit/s F/O port 21

1.4.4 PoE ports 21

1.4.5 Combo ports 22

1.5 Display elements 22

1.5.1 Device state 23

1.5.2 Port status 24

1.6 Management interfaces 25

1.6.1 V.24 interface (external management) 25

1.6.2 USB interface 26

1.7 Signal contact 26

2 Installation 27

2.1 Checking the package contents 27

2.2 Installing an SFP transceiver (optional) 27

4

Installation MACH104

Release 08 01/2019

2.3 Wiring and installing the signal contact 28

2.4 Installing the device and grounding 29

2.4.1 Selecting the assembly location 29

2.4.2 Mounting on a flat surface 29

2.4.3 Mounting in a switch cabinet 29

2.4.4 Mounting on the wall 30

2.4.5 Grounding the device 31

2.5 Operating the device 32

2.6 Connecting data cables 32

3 Making basic settings 33

3.1 Default settings 34

4 Maintenance and service 35

5 Deinstallation 36

5.1 Removing the device 36

5.2 Removing an SFP transceiver (optional) 36

6 Technical data 37

6.1 General technical data 37

6.2 Dimension drawings 38

6.3 EMC and immunity 38

6.4 Network range 40

6.5 Power consumption/power output 43

7 Scope of delivery, order numbers and

accessories 44

8 Underlying technical standards 47

A Further support 48

Installation MACH104

Release 08 01/2019

5

Safety instructions

 General safety instructions

You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
 Before connecting any cable, read this document, and the safety

instructions and warnings.

 Operate the device with undamaged components exclusively.
 The device is free of any service components. In case of a damaged

or malfunctioning device, turn off the supply voltage and return the
device to Hirschmann for inspection.

 Qualification requirements for personnel

 Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

 Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.

 Qualified personnel are aware of the dangers that exist in their work.
 Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

 Qualified personnel receive training on a regular basis.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,
or equipment damage.

6

Installation MACH104

Release 08 01/2019

 Certified usage

 Use the product only for the application cases described in the

Hirschmann product information, including this manual.

 Operate the product only according to the technical specifications.

See “Technical data” on page 37.

 Connect to the product only components suitable for the requirements

of the specific application case.

 National and international safety regulations

 Verify that the electrical installation meets local or nationally applicable

safety regulations.

 Grounding the device

The device is grounded via the power supply connections.

 Requirements for connecting electrical wires

Before connecting the electrical wires, always verify that the
requirements listed are complied with.

 Requirements for connecting the supply voltage

Before connecting the supply voltage, always verify that the requirements
listed are complied with.

The following requirements apply without restrictions:

 The electrical wires are voltage-free.
 The cables used are permitted for the temperature range of the application case.
 Only switch on the device when the casing is closed.
 Relevant for North America:

Exclusively use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire.

Prerequisites:
All of the following requirements are complied with:

 The supply voltage corresponds to the voltage specified on the type plate of the device.
 The power supply conforms to overvoltage category I or II.
 The power supply has an easily accessible disconnecting device (for example a switch or

a plug). This disconnecting device is clearly identified. So in the case of an emergency, it is
clear which disconnecting device belongs to which power supply cable.

 This applies to the following device variants only:

 MACH104-20TX-FR...

Unplug every non-heating device coupling to disconnect the device from the power supply.

 This applies to the following device variants only:

 MACH104-20TX-FR...

The wire diameter of the power supply cable is at least 1 mm² (North America: AWG16) on
the supply voltage input.

 The cross-section of the ground conductor is the same size as or bigger than the cross-

section of the power supply cables.

 The power supply cable is suitable for the voltage, the current and the physical load.

Hirschmann recommends a wire diameter of 0.5 mm² to 0.75 mm² (AWG20 up to AWG18).

The following requirements apply alternatively:

Installation MACH104

Release 08 01/2019

7

Relevant when the device is supplied via 1 voltage input:
Alternative 1 The power supply complies with the requirements for a limited power source

(LPS) as per EN 60950-1.

Alternative 2 Relevant for North America:

The power supply complies with the requirements according to NEC Class 2.

Alternative 3 All of the following requirements are complied with:

 The power supply complies with the requirements for a safety extra-low

voltage (SELV) as per IEC/EN 60950-1.

 Supply with DC voltage:

A fuse suitable for DC voltage is located in the plus conductor of the power
supply.
The minus conductor is on ground potential. Otherwise, a fuse is also
located in the minus conductor.
Regarding the properties of this fuse:

See “Technical data” on page 37.

 Supply with AC voltage:

A fuse is located in the outer conductor of the power supply.
The neutral conductor is on ground potential at both voltage inputs.
Otherwise, a fuse is also located in the neutral conductor.
Regarding the properties of this fuse:

See “Technical data” on page 37.

Relevant when the device is supplied via 2 voltage inputs:
Alternative 1 The total voltage supply meets the requirements for a limited power source

(LPS) as per EN 60950-1.

Alternative 2 Relevant for North America:

The total voltage supply complies with the requirements as per NEC Class 2.

Alternative 3 All of the following requirements are complied with:

 The power supply complies with the requirements for a safety extra-low

voltage (SELV) as per IEC/EN 60950-1.

 Supply with DC voltage:

A fuse suitable for DC voltage is located at both voltage inputs in the plus

conductor of the power supply.

The minus conductor is on ground potential at both voltage inputs.

Otherwise, a fuse is also located in the minus conductor.

Regarding the properties of this fuse:

See “Technical data” on page 37.

 Supply with AC voltage:

A fuse is located at both voltage inputs in the outer conductor of the power

supply.

The neutral conductor is on ground potential at both voltage inputs.

Otherwise, a fuse is also located in the neutral conductor.

Regarding the properties of this fuse:

See “Technical data” on page 37.

Prerequisites:

8

Installation MACH104

Release 08 01/2019

 Supply voltage

The supply voltage is connected to the device casing through protective
elements exclusively.
The supply voltage is electrically isolated from the casing.

 Device casing

Only technicians authorized by the manufacturer are permitted to open
the casing.
 Never insert sharp objects (small screwdrivers, wires, etc.) into the

inside of the device.

 Keep the ventilation slits free to ensure good air circulation.
 Make sure there is at least 3.94 in (10 cm) of space in front of the

ventilation slits of the casing.

 Mount the device horizontally or vertically, either as a desktop device,

in the switch cabinet (figure 12 on page 30) or on the wall (figure 14 on

page 31).

Installation MACH104

Release 08 01/2019

9

 CE marking

The labeled devices comply with the regulations contained in the following
European directive(s):

2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.

2014/30/EU (EMC)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic
compatibility.

2014/35/EU
Directive of the European Parliament and of the Council on the
harmonisation of the laws of the Member States relating to the making
available on the market of electrical equipment designed for use within
certain voltage limits.

In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:

Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany

The product can be used in the industrial sector.

 Interference immunity: EN 61000-6-2
 Emitted interference: EN 55032

Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.

Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.

 LED or laser components

LED or LASER components according to IEC 60825-1 (2014):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT

10

Installation MACH104

Release 08 01/2019

 FCC note:

This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate these
frequencies. If it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a residential area can also cause interference, and in this
case the user is obliged to cover the costs of removing the interference.

 BSMI note for use in Taiwan

Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.

Devices with a specification according to BSMI standards CNS 13438,
CNS 14336-1 and CNS 15663 are marked on the device label.

᝾֋٬Ҕޣ;!

೭ࢂҘᜪޑၗૻౢ ࠔǴӧۚՐޑᕉნύ٬ҔǴёૈ཮೷ԋ৔ᓎυᘋǴӧ೭

ᅿ

௃ݩΠǴ٬Ҕޣ཮೏؃௦ڗࢌ٤፾྽ޑჹ฼Ƕ

D45625

RoHS

Installation MACH104

Release 08 01/2019

11

Declaration o

f

hazardous substances according to

C

hinese regulatory standar

d

estr

i

cte

d

su

b

stances an

d

t

h

e

i

r c

h

em

i

ca

l

sym

b

o

l

ercur

y

admium Hexavalent

C

hromiu

m

o

l

y

b

rom

i

nate

d

bi

p

h

eny

l

s

o

l

y

b

rom

i

nate

d

di

p

h

eny

l

et

h

ers

omponent

eta

l

components

r

i

nte

d

c

i

rcu

i

t

b

oar

d

assem

bly

Ҕނ፦֖Ԗ௃ݩ኱Ңᖂܴ

ൂϡ

ߎឦ೽ҹ

೛ഢӜᆀǺҬඤᐒǴࠠဦȐࠠԄȑǺ

MACH104-20TX-FR...

MACH104-20TX-FR...

MACH104-20TX-F-4PoE...

Equipment name:

S

witch, Model desi

g

nation:

Ҕނ፦ϷځϯᏢ಄ဦ

ႉ

؄ᙿ

Ϥሽ

ӭྜྷᖄ

ӭྜྷΒ⾸

ႝၡኳಔ

༟ጤکᆫ!ӝނ೽ҹ

ႝྍϡҹ

ower supp

l

y un

i

t

ഢԵIJįġȺຬрıįIJġŸŵġĦȻϷȺຬрıįıIJġŸŵġĦȻ߯ࡰҔނ፦ϐԭϩК֖ໆຬрԭϩК֖ໆ୷ྗǶ

Note 1: “Exceeding 0.1 wt%” and “exceeding 0.01 wt%” indicates that the amount of the restricted substance within the component exceeds the

reference percentage limit

.

Note 2:

“O

” indicates that the amount o

f

the restricted substance does not exceed the re

f

erence percentage limit.

Note 3:

“

X” indicates that the amount o

f

the restricted substance corresponds with the exemption.

ഢԵijįȺOȻ߯ࡰ၀໨Ҕނ፦ϐԭϩК֖ໆ҂ຬрԭϩК֖ໆ୷ྗǶ

ഢԵĴįȺXȻ߯ࡰ၀໨Ҕނ፦ࣁ௨ନ໨ҞǶ

12

Installation MACH104

Release 08 01/2019

 Relevant for installations in switch cabinets according to

UL 60950-1

 Higher ambient air temperature during operation: If installed in a

closed switch cabinet or a multi-unit switch cabinet, the ambient air
temperature inside the switch cabinet during operation can be higher
than the ambient air temperature in the room. Install devices in
environments that are compatible with the maximum ambient air
temperature of the device.

 Reduced air flow: When you install the device in a switch cabinet,

make sure that a sufficient air flow is guaranteed in order to safely
operate your devices.

 Mechanical stress: Check for potential dangers resulting from

unevenly distributed weight when you install the device in a switch
cabinet.

 Electric circuit overloading: Observe the effects of electric circuit

overloads on the overload current protection and the power supply
cables when you connect devices to the power supply. Refer to the
device parameters specified on the type plate of the device.

 Safe grounding: Make sure that devices installed in switch cabinets

are grounded safely. When you install a device in a switch cabinet,
also watch out for power supply connections other than the direct
connections to the circuit branch (for example socket boards).

 Recycling note

After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

Installation MACH104

Release 08 01/2019

13

About this manual

The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.

The following manuals are available as PDF files on the Internet on the
Hirschmann product pages (www.hirschmann.com):

 Installation user manual
 Basic Configuration user manual
 Redundancy Configuration user manual
 Reference manual for the graphical user interface
 Command Line Interface reference manual

The Network Management Software Industrial HiVision provides you with
options for smooth configuration and monitoring. You find further information
on the Internet at the Hirschmann product pages: http://

www.hirschmann.com/en/QR/INET-Industrial-HiVision

14

Installation MACH104

Release 08 01/2019

Legend

The symbols used in this manual have the following meanings:

 Listing

 Work step



Subheading

Installation MACH104

Release 08 01/2019

15

1 Description

1.1 General device description

The MACH104 family provides you with a range of device variants.
The device is designed for the special requirements of industrial automation.
The device meets the relevant industry standards, provides very high
operational reliability, even under extreme conditions, and also long-term
reliability and flexibility.

The devices with software variant L2... allow you to set up switched industrial
Ethernet networks that conform to the IEEE 802.3 standard.

The devices with software variant L2... allow you to set up switched and
routed industrial Ethernet networks that conform to the IEEE 802.3 standard.
The devices work without a fan.

The following installation options are available:

 19" switch cabinet
 Mounting on a flat surface

You have the option of choosing various media to connect to the end devices
and other network components:

 Twisted pair cable
 Multimode F/O
 Singlemode F/O

The ring redundancy concept allows the network to be reconfigured quickly
after a failure.

There are convenient options for managing the device. Manage your devices
via:

 Web browser
 Telnet
 Network management software (for example Industrial HiVision)
 V.24 interface (locally on the device)

The device provides you with a large range of functions, which the manuals
for the operating software inform you about. You can download these
manuals as PDF files from the Internet on the Hirschmann product pages
(www.hirschmann.com).
The Hirschmann network components help you ensure continuous
communication across all levels of the company.

16

Installation MACH104

Release 08 01/2019

1.2 Description of the device variants

1.2.1 MACH104-20TX-F...: Devices with 24 GB ports

 MACH104-20TX-F...

 4 Gigabit Ethernet combo ports
 20 Gigabit Ethernet ports

Figure 1: Overview over interfaces, display and operating elements

of the MACH104-20TX-F...
1 - MACH104-20TX-F... device
2 - LED display elements
3 - Signal contact
4 - USB interface
5 - V.24 interface for external management
6 - See the following table, column 1
7 - See the following table, column 2
8 - Power supply connection (on the back of the device)

4 × Gigabit Ethernet ports 4 × Gigabit Ethernet combo ports

10/100/1000 Mbit/s twisted pair,
RJ45 sockets

100/1000 Mbit/s F/O, SFP slots
Alternatively:
10/100/1000 Mbit/s twisted pair, RJ45 sockets

V.24USB

Aufkleber MAC-Adresse

P

FAULT

FAULT

Sb

RM

5

6

7

8

13

24

911

10 12

13 15

14 16

17 19

18 20

21 23

22 24

MACH104-20TX-F

2 3 4 51

6

7

7

5

13

911

13 15

17 19 21 23

8

6

24

10 12

14 16

18 20 22 24

6 6 6 6

8

Installation MACH104

Release 08 01/2019

17

1.2.2 MACH104-20TX-FR...: Devices with 24 GB ports and

redundant power supply

 MACH104-20TX-FR...

 4 Gigabit Ethernet combo ports
 20 Gigabit Ethernet ports
 The power supply is designed redundantly.

Figure 2: Overview over interfaces, display and operating elements

of the MACH104-20TX-FR...
1 - MACH104-20TX-FR... device
2 - LED display elements
3 - Signal contact
4 - USB interface
5 - V.24 interface for external management
6 - See the following table, column 1
7 - See the following table, column 2
8 - P1: Power supply connection (on the back of the device)
9 - P2: Redundant power supply connection
(on the back of the device)

4 × Gigabit Ethernet ports 4 × Gigabit Ethernet combo ports

10/100/1000 Mbit/s twisted pair,
RJ45 sockets

100/1000 Mbit/s F/O, SFP slots
Alternatively:
10/100/1000 Mbit/s twisted pair, RJ45 sockets

6

7

5

13

911

13 15

17 19 21 23

8

6

24

10 12

14 16

18 20 22 24

6 6 6 6

7

V.24USB

Aufkleber MAC-Adresse

P

FAULT

FAULT

Sb

RM

5

6

7

8

13

24

911

10 12

13 15

14 16

17 19

18 20

21 23

22 24

MACH104-20TX-FR

9

8

2 3 4 51

18

Installation MACH104

Release 08 01/2019

1.2.3 MACH104-20TX-F-4-PoE...: Devices with 24 GB ports,
4 of them PoE ports

 MACH104-20TX-F-4-PoE...

 4 Gigabit Ethernet combo ports
 20 Gigabit Ethernet ports, 4 of which are PoE-capable
 Integrated PoE voltage supply for 4 PoE ports

Figure 3: Overview over interfaces, display and operating elements

of the MACH104-20TX-F-4-PoE...
1 - MACH104-20TX-F-4-PoE... device
2 - LED display elements
3 - Signal contact
4 - USB interface
5 - V.24 interface for external management
6 - See the following table, column 1
7 - See the following table, column 2
8 - See the following table, column 3
9 - Power supply connection (on the back of the device)
10 - Integrated PoE PSU (on the back of the device)

4 × Gigabit Ethernet PoE
ports

4 × Gigabit Ethernet combo ports 4 × Gigabit Ethernet

ports

10/100/1000 Mbit/s twisted
pair, RJ45 sockets with PoE

100/1000 Mbit/s F/O, SFP slots
Alternatively:
10/100/1000 Mbit/s twisted pair, RJ45
sockets

10/100/1000 Mbit/s
twisted pair, RJ45
sockets

6

7

5

13

911

13 15

17 19 21 23

8

6

24

10 12

14 16

18 20 22 24

8 8 8 8

7

V.24USB

Aufkleber MAC-Adresse

P

FAULT

FAULT

Sb

RM

5

6

7

8

13

24

911

10 12

13 15

14 16

17 19

18 20

21 23

22 24

MACH104-20TX-F-4PoE

P

2 3 4 51

10

9

Installation MACH104

Release 08 01/2019

19

1.3 Supply voltage

Note: Note the safety instructions in “Requirements for connecting electrical

wires” on page 6.

1.3.1 MACH104-20TX-F...

Supply voltage is connected via a non-heating appliance socket.

Figure 4: MACH104-20TX-F connections on the back of the device

1 - Power supply 100 V AC ... 240 V AC
2 - MACH104-20TX-F... device

1.3.2 MACH104-20TX-FR...

Supply voltage is connected via non-heating appliance sockets.
The supply voltage can be connected redundantly. Both inputs are
uncoupled. The load is not distributed. With redundant supply, the standard
power supply supplies the device on its own. The redundant power supply
becomes active automatically if the standard power supply fails. Normally the
redundant power supply runs in stand-by mode.
The supply voltage is electrically isolated from the casing.

Figure 5: MACH104-20TX-FR... connections on the back of the device

1 - Standard power supply 100 V AC ... 240 V AC
2 - MACH104-20TX-FR... device
3 - Redundant power supply 100 V AC ... 240 V AC

With a non-redundant supply of the supply voltage, the device reports the
loss of a supply voltage. You can prevent this message by applying the
supply voltage via both inputs, or by changing the configuration in the
Management.

1

2

31 2

20

Installation MACH104

Release 08 01/2019

1.3.3 MACH104-20TX-F-4-PoE...

Supply voltage is connected via a non-heating appliance socket.

Figure 6: MACH104-20TX-F-4-PoE... connections on the back of the device

1 - Standard power supply 100 V AC ... 240 V AC
2 - MACH104-20TX-F-4-PoE... device

1.4 Ethernet ports

You can connect end devices and other segments to the device ports using
twisted pair cables or optical fibers (F/O).

1.4.1 10/100/1000 Mbit/s twisted pair port

This port is an RJ45 socket.
The 10/100/1000 Mbit/s twisted pair port allows you to connect network
components according to the IEEE 802.3 10BASE-T/100BASE-TX/
1000BASE-T standard.
This port supports:

 Autonegotiation
 Autopolarity
 Autocrossing (if autonegotiation is activated)
 1000 Mbit/s full duplex
 100 Mbit/s half-duplex mode, 100 Mbit/s full duplex mode
 10 Mbit/s half-duplex mode, 10 Mbit/s full duplex mode

Note: Some of these ports also support Power over Ethernet (PoE).

See “PoE ports” on page 21.

Delivery state: Autonegotiation activated
The port casing is electrically connected to the front panel.
The pin assignment corresponds to MDI-X.

12

Installation MACH104

Release 08 01/2019

21

1.4.2 100 Mbit/s F/O port

This port is an SFP slot.
The 100 Mbit/s F/O port allows you to connect network components
according to the IEEE 802.3 100BASE-FX standard.
This port supports:

 Full or half duplex mode

Default setting: Full duplex

1.4.3 1000 Mbit/s F/O port

This port is an SFP slot.
The 1000 Mbit/s F/O port offers you the ability to connect network
components according to the IEEE 802.3 100BASE-SX/1000BASE-LX
standard.
This port supports:

 Autonegotiation
 Full duplex mode

Delivery state: Autonegotiation activated

1.4.4 PoE ports

The device variants MACH104-20TX-F-4-PoE... support Power over
Ethernet (PoE) in accordance with IEEE 802.3af.

Figure Pin Function Ports with PoE support:

PoE voltage feed

1 BI_DB+ Minus terminal of the supply voltage
2BI_DB− Minus terminal of the supply voltage
3 BI_DA+ Plus terminal of the supply voltage
4BI_DD+
5BI_DD−
6BI_DA− Plus terminal of the supply voltage
7BI_DC+
8BI_DC−

Table 1: Pin assignment of a 1000 MBit/s TP interface in MDI-X mode, RJ45

socket - for PoE with the power supplied via the wire pairs transmitting the
signal

Ports PoE support

1 to 4 Yes
5 to 20 No

Table 2: Twisted-pair ports and PoE support

1
2
3
4
5
6
7
8

22

Installation MACH104

Release 08 01/2019

The PoE ports support the connection and a remote power supply of (for
example) IP phones (Voice-over-IP), webcams, sensors, print servers, and
WLAN access points. With PoE, these end devices are powered via the
twisted pair cable.

The following applies to PoE ports:

 max. Powered Device (PD) class 0 (15.4 W)
 The PoE power is supplied via the wire pairs transmitting the signal

(phantom voltage).

 The individual ports (joint PoE voltage) are not electrically insulated from

each other.

1.4.5 Combo ports

You have the option of alternatively connecting a twisted pair cable via a
RJ45 socket or an optical fiber via a SFP transceiver to a combo port.
By inserting a SFP transceiver, you deactivate automatically the
corresponding twisted pair interface.

1.5 Display elements

After the supply voltage is set up, the Software starts and initializes the
device. Afterwards, the device performs a self-test. During this process,
various LEDs light up.
The process takes around 15 seconds.

Figure 7: MACH104-Display elements

1 - Display elements device status
2 - Display elements port status

V.24USB

Aufkleber MAC-Adresse

P

FAULT

FAULT

Sb

RM

5

6

7

8

13

24

911

10 12

13 15

14 16

17 19

18 20

21 23

22 24

MACH104-20TX-F

7

5

13

911

13 15

17 19 21 23

8

6

24

10 12

14 16

18 20 22 24

21

Installation MACH104

Release 08 01/2019

23

1.5.1 Device state

These LEDs provide information about conditions which affect the operation
of the whole device.
The following table applies to the stated device variants only:

 MACH104-20TX-FR...

The following table applies to the stated device variants only:

 MACH104-20TX-F...
 MACH104-20TX-F-4-PoE...

The following table applies to every device variant:

LED Display Color Activity Meaning

P Supply

voltage

— none Supply voltages 1 and 2 are too low.
green lights up Supply voltage 1 and 2 is on
yellow lights up Supply voltage 1 or 2 is on

LED Display Color Activity Meaning

P Supply

voltage

— none Supply voltage is too low
green lights up Supply voltage is on

LED Display Color Activity Meaning

Sb Stand-by — none Stand-by mode not enabled

green lights up Standby mode enabled

FAULT Signal

contact

— none The signal contact is closed, it is not

reporting any detected errors.

red lights up The signal contact is open - it is reporting a

detected error.

RM Ring

Manager

— none The RM function is deactivated.
green lights up The RM function is active.

The redundant port is disabled.

flashing The device detects an incorrect

configuration of the HIPER-Ring (for
example the ring is not connected to the ring
port).

yellow lights up The RM function is active.

The redundant port is enabled.

FAULT

RM

Sb

P

24

Installation MACH104

Release 08 01/2019

If the manual setting is active on the signal contact “FAULT”, then the error
display is independent of the setting of the signal contact.

1.5.2 Port status

These LEDs display port-related information.

RM
and
Sb

ACA memory
operations

green Flashing

alternately

Error in the memory operation

flashes
synchronously
2 × per period

Saves a configuration file from the storage
medium ACA to the device.

flashes
synchronously
1 × per period

Saves a configuration file from the device to
the storage medium ACA.

LED Display Color Activity Meaning

LS Link status — none Device detects an invalid or missing

link

green lights up Device detects a valid link

flashes 1 time a period Port is switched to stand-by
flashes 3 times a

period

Port is switched off

DA Data traffic yellow flashing Device is transmitting and/or receiving

data

LED Display Color Activity Meaning

LS DA2

LS DA1

Installation MACH104

Release 08 01/2019

25

1.6 Management interfaces

1.6.1 V.24 interface (external management)

The V.24 interface is an RJ11 socket.
The V.24 user interface is serial and allows you to connect the following
devices directly:

 External management station (VT100 terminal or PC with appropriate

terminal emulation). With this management station, the Command Line
Interface (CLI) is available to you. Furthermore, the system monitor is
available to you at the system start.

 The AutoConfiguration Adapter ACA11

The interface casing is electrically connected to the front panel.
The V.24 interface is not electrically isolated from the supply voltage.

Figure 8: Pin assignment of the V.24 interface and the DB9 plug

You will find the order number for the terminal cable, which is ordered
separately, in the Technical Data section (see on page 37 “Technical data”).

VT100 terminal settings

Speed 9600 Baud
Data 8 bit
Stopbit 1 bit
Handshake off
Parity none

1

1

8

5

6

2
3

5

1
2
3
4
5
6

CTS
n.c.
TX
GND
RX
RTS

RJ11

DB9

RJ11

DB9

26

Installation MACH104

Release 08 01/2019

1.6.2 USB interface

The USB interface allows you to connect the AutoConfiguration Adapter
ACA21-USB (EEC) storage medium. This is used for saving/loading the
configuration data and diagnostic information, and for loading the software.

See “Accessories and order numbers” on page 44.

1.7 Signal contact

Figure 9: MACH104 device, front view

1 - Signal contact

The signal contact is a potential-free relay contact. The signal contact is open
when the device is not connected to a power supply.
The signal contact allows you to control external devices or monitor device
functions.
In the configuration, you specify how the device uses the signal contact.
You find detailed information regarding possible applications and
configuration of the signal contact in the software user documentation on the
Hirschmann product pages (www.hirschmann.com).

Figure Pin Function

1VCC (VBus)
2 − Data
3 + Data
4 Ground (GND)

Table 3: Pin assignment of the USB interface

1

2

4

3

V.24USB

Aufkleber MAC-Adresse

P

FAULT

FAULT

Sb

RM

5

6

7

8

13

24

911

10 12

13 15

14 16

17 19

18 20

21 23

22 24

MACH104-20TX-F

1

Installation MACH104

Release 08 01/2019

27

2Installation

On delivery, the device is ready for operation.
The following procedure has been proven to be successful for the assembly
of the device:

 Checking the package contents
 Installing an SFP transceiver (optional)
 Wiring and installing the signal contact
 Installing the device and grounding
 Operating the device
 Connecting data cables

Note: Note the safety instructions in “Requirements for connecting electrical

wires” on page 6.

2.1 Checking the package contents

 Check whether the package includes all items named in the section

“Scope of delivery, order numbers and accessories” on page 44.

 Check the individual parts for transport damage.

2.2 Installing an SFP transceiver (optional)

Prerequisites:

Exclusively use Hirschmann SFP transceivers.

See “Accessories and order numbers” on page 44.

Figure 10: Installing SFP transceivers: Installation sequence

1

2

3

28

Installation MACH104

Release 08 01/2019

Proceed as follows:

 Take the SFP transceiver out of the transport packaging (1).
 Remove the protection cap from the SFP transceiver (2).
 Push the SFP transceiver with the lock closed into the slot until it latches

in (3).

2.3 Wiring and installing the signal contact

Figure 11: 2-pin terminal block

Every time you connect the electrical conductors, make sure that the
following requirements are met:

 The electrical wires are voltage-free.
 The connected voltage is limited by a current limitation device or a fuse.

Observe the electrical threshold values for the signal contact.

See “General technical data” on page 37.

 Remove the terminal connector from the device.
 Connect the signal contact lines with the terminal block connections.
 Mount the terminal block for the signal contact on the front of the device

using the screw lock. Check whether the terminal block is correctly
plugged and screwed on.

You find the prescribed tightening torque in chapter:

“General technical data” on page 37

WARNING

ELECTRIC SHOCK

Never insert sharp objects (small screwdrivers, wires, or similar items) into
the connection terminals for the signal lines, and do not touch the terminals.

Failure to follow these instructions can result in death, serious injury,
or equipment damage.

FAULT

Installation MACH104

Release 08 01/2019

29

2.4 Installing the device and grounding

The device can be mounted on a flat surface, in a 19" standard switch
cabinet, or on the wall.

2.4.1 Selecting the assembly location

Select the assembly location according to the safety guidelines (see on

page 5 “Safety instructions”).

When selecting the assembly location, also make sure the following
requirements are met:

 The assembly location can be accessed for maintenance and repair work.
 The LED display elements are clearly visible.
 Twisted pair cables are at a sufficient distance from potential sources of

electrical interference, such as power supply cables.

 The device has a separate power source with a ground connection. The

power supply can be interrupted by means of a separate isolator or power
switch. We recommend using overvoltage protection for all devices.

2.4.2 Mounting on a flat surface

Before operating the device on a flat surface, such as a table, stick the
supplied casing feet onto the bottom of the device, with approx. 0.8 in (2 cm)
of space from the corners.
 If necessary, remove any dirt from the bottom of the device where you

want to place the stick-on feet.

 Remove the protective foil from the adhesive surface of a casing foot and

attach the casing foot on the device.

2.4.3 Mounting in a switch cabinet

Note: Note the instructions on installations in 19" switch cabinets according
to UL 60950-1.

See “Relevant for installations in switch cabinets according to UL 60950-1”
on page 12.

Note: For more information on sliding/mounting rails and how to install them,
please contact your switch cabinet manufacturer.

The devices are designed to be mounted in a 19" switch cabinet.
 Ensure adequate ventilation. If necessary, install an additional fan in the

switch cabinet to prevent the device from overheating.

 Measure the depth of the 19" switch cabinet so as to allow the power

supply cables to be fitted at the back and the data cables to be fitted at
the front.

 Assemble the sliding or mounting rails in the 19" switch cabinet as

specified by the manufacturer.

30

Installation MACH104

Release 08 01/2019

Figure 12: Assembly in a switch cabinet with sliding/mounting rails

1 - MACH104 device
2 - sliding/mounting rail
3 - 19" switch cabinet

Figure 13: Mounting the MACH104 in the 19" cabinet

 Fasten the device by screwing the brackets to the switch cabinet.

Note: When operating the device in an environment with strong vibrations,
you have the option to additionally fasten the device to the switch cabinet
using 2 holding brackets on the back of the device.
You obtain the additional brackets as accessories.

See “Accessories and order numbers” on page 44.

2.4.4 Mounting on the wall

 Remove the screws on the pre-installed mounting brackets.
 Move the two pre-installed mounting brackets into the position shown

below.

 Use the screws to secure the mounting brackets on the device.

1

3

2

V.24USB

Aufkleber MAC-Adresse

P

FAULT

FAULT

Sb

RM

5

6

7

8

13

24

911

10 12

13 15

14 16

17 19

18 20

21 23

22 24

MACH104-20TX-F

Installation MACH104

Release 08 01/2019

31

 Additionally attach 2 brackets to the back of the device.

See figure 14.

You obtain the additional brackets as accessories.

See “Accessories and order numbers” on page 44.

 Fasten the device by screwing the brackets to the wall.

Figure 14: Vertical mounting on the wall

2.4.5 Grounding the device

The device is grounded via the power supply connections.

32

Installation MACH104

Release 08 01/2019

2.5 Operating the device

Note: Note the safety instructions in “Requirements for connecting electrical

wires” on page 6.

By connecting the voltage supply via the voltage supply socket(s), you start
the operation of the device.

2.6 Connecting data cables

Note: Verify that you connect only optical ports with the same optical
transmission properties with each other.

Further information:

See “Ethernet ports” on page 20.

 Connect the data cables according to your requirements.

WARNING

ELECTRIC SHOCK

Connect only a supply voltage that corresponds to the type plate of your
device.

Failure to follow these instructions can result in death, serious injury,
or equipment damage.

Installation MACH104

Release 08 01/2019

33

3 Making basic settings

Note: Two or more devices configured with the same IP address can cause
unpredictable operation of your network.
Install and maintain a process that assigns a unique IP address to every
device in the network.

When you install the device for the first time enter the IP parameters.

The device provides the following options for entering the IP parameters
during the first installation:

 Configuration via DHCP (state on delivery)
 Input via the V.24 interface
 Input via the HiView or Industrial HiVision application. You find further

information about the applications HiView or Industrial HiVision on the
Internet at the Hirschmann product pages:

HiView

http://www.hirschmann.com/en/QR/INET-HiView

Industrial HiVision

http://www.hirschmann.com/en/QR/INET-Industrial-HiVision

 Configuration via BOOTP
 Configuration via DHCP (Option 82)
 AutoConfiguration Adapter

Further information on the basic settings of the device can be found in the
“Basic Configuration” user manual.

34

Installation MACH104

Release 08 01/2019

3.1 Default settings

 The device looks for the IP address using DHCP
 Management password:

user, password: public (read only)
admin, password: private (read and write)

 V.24 data rate: 9600 Baud
 Ring redundancy disabled
 Ethernet ports: link status is not evaluated (signal contact)
 Optical 100 Mbit/s ports: 100 Mbit/s full duplex

Other ports: Autonegotiation

 Redundancy manager disabled

(DIP switch RM and Standby: ON)

 Standby coupling disabled

(DIP switch RM and Standby: ON)
Port 3 = control port, Port 4 = coupling port for redundant ring coupling

 Rapid Spanning Tree enabled

Installation MACH104

Release 08 01/2019

35

4 Maintenance and service

 When designing this device, Hirschmann largely avoided using high-wear

parts. The parts subject to wear and tear are dimensioned to last longer
than the lifetime of the product when it is operated normally. Operate this
device according to the specifications.

See “Technical data” on page 37.

 Relays are subject to natural wear. This wear depends on the frequency

of the switching operations. Check the resistance of the closed relay
contacts and the switching function depending on the frequency of the
switching operations.

 Hirschmann is continually working on improving and developing their

software. Check regularly whether there is an updated version of the
software that provides you with additional benefits. You find information
and software downloads on the Hirschmann product pages on the
Internet (http://www.hirschmann.com).

 Internal fuses are triggered only in the case of a detected error in the

device. In case of damage or malfunction of the device, turn off the supply
voltage and return the device to the plant for inspection.

 Depending on the degree of pollution in the operating environment, check

at regular intervals that the ventilation slots in the device are not
obstructed.

Note: You find information on settling complaints on the Internet at http://

www.beldensolutions.com/en/Service/Repairs/index.phtml.

36

Installation MACH104

Release 08 01/2019

5Deinstallation

5.1 Removing the device

 Disconnect the data cables.
 Disable the supply voltage.
 Disconnect the supply voltage.
 Remove the terminal connector from the device.
 To detach the device from the switch cabinet or the wall, remove the

screws from the brackets on the device.

Figure 15: Disassembling the device

5.2 Removing an SFP transceiver (optional)

Figure 16: De-installing SFP transceivers: De-installation sequence

Proceed as follows:

 Open the locking mechanism of the SFP transceiver (1).
 Pull the SFP transceiver out of the slot via the open locking

mechanism (2).

 Close the SFP transceiver with the protection cap (3).

V.24USB

Aufkleber MAC-Adresse

P

FAULT

FAULT

Sb

RM

5

6

7

8

13

24

911

10 12

13 15

14 16

17 19

18 20

21 23

22 24

MACH104-20TX-F

1

2

3

Installation MACH104

Release 08 01/2019

37

6 Technical data

6.1 General technical data

Dimensions See “Dimension drawings” on page 38.
Weight MACH104-20TX-F... 9.26 lb (4.2 kg)

MACH104-20TX-FR... 9.7 lb (4.4 kg)
MACH104-20TX-F-4-PoE... 10.14 lb (4.6 kg)

Supply voltage Rated voltage range 100 V AC ... 240 V AC, 50 Hz ... 60 Hz

Voltage range including
maximum tolerances

90 V AC ... 265 V AC, 47 Hz ... 63 Hz

Current
consumption

Rated current for devices
without PoE

max. 0.3 A (240 V AC)
max. 0.5 A (100 V AC)

Rated current for devices with
PoE

max. 0.9 A (240 V AC)

max. 1.7 A (100 V AC)
Activation current typ. < 40 A at 265 V AC and cold start
PoE power Maximum number of Powered

Devices (PDs)

This applies to the following device

variants only:

MACH104-20TX-F-4-PoE...

4 × Powered Device (PD) Class 0 (15.4 W)
Power loss buffer > 12 ms (115 V AC)
Overload current

protection at input

Non-replaceable fuse

Climatic conditions
during operation

Ambient air temperature

a

a. Temperature of the ambient air at a distance of 2 in (5 cm) from the device

+32 °F ... +122 °F (0 °C ... +50 °C)

Humidity 20 % ... 90 %

(non-condensing)

Air pressure min. 795 hPa (+6562 ft; +2000 m)

max. 1060 hPa (−1312 ft; −400 m)
Climatic conditions

during storage

Ambient air temperature

b

b. Temperature of the ambient air at a distance of 2 in (5 cm) from the device

–4 °F ... +185 °F (−20 °C ... +85 °C)

Humidity 10 % ... 95 %

(non-condensing)

Air pressure min. 700 hPa (+9842 ft; +3000 m)

max. 1060 hPa (−1312 ft; −400 m)
Signal contact Switching current max. 1 A, SELV

Switching voltage max. 60 V DC or max. 30 V AC, SELV
Connection type 2-pin terminal block

max. conductor cross section AWG16

(1.3 mm²)

Tightening torque 2.2 lb-in (0.25 Nm)
Pollution degree 2
Protection classes Laser protection Class 1 in compliance with IEC 60825-1

Degree of protection IP30

38

Installation MACH104

Release 08 01/2019

6.2 Dimension drawings

6.3 EMC and immunity

EMC interference immunity

IEC/EN 61000-4-2 Electrostatic discharge

Contact discharge
Air discharge

6kV
8kV

IEC/EN 61000-4-3 Electromagnetic field

80 MHz ... 3000 MHz max. 20 V/m

IEC/EN 61000-4-4 Fast transients (burst)

Power line
Data line

2kV
4kV

mm
inch

31,75

1.25

462,6

18.21

43,9

1.73

3,3

0.13

3,3

0.13

4,5

0.18

342

13.46

19,3

0.76

19,3

0.76

444

17.48

Installation MACH104

Release 08 01/2019

39

IEC/EN 61000-4-5 Voltage surges

Power line, line / line
Power line, line / ground
Data line

1 kV
2kV
4kV

IEC/EN 61000-4-6 Conducted disturbances

150 kHz ... 80 MHz 10 V

EN 61000-4-9 Pulse magnetic fields 300 A/m

EMC interference emission

EN 55032 Class A Yes
FCC 47 CFR Part 15 Class A Yes

EMC interference immunity

40

Installation MACH104

Release

08

01/2019

6.4 Network range

Note: The line lengths specified for the transceivers apply for the respective fiber data (fiber attenuation and Bandwidth
Length Product (BLP)/ Dispersion).

10/100/1000 Mbit/s twisted pair port

Length of a twisted pair segment max. 328 ft (100 m) (for Cat5e cable)

Table 4: Network range: 10/100/1000 Mbit/s twisted pair port

Product code
M-FAST-SFP-...

Mode

a

a. MM = Multimode, SM = Singlemode, LH = Singlemode Longhaul

Wave length Fiber System

attenuation

Example for F/O
cable length

b

b. Including 3 dB system reserve when compliance with the fiber data is observed.

Fiber
attenuation

BLP/Dispersion

-MM/LC... MM 1310 nm 50/125 µm 0 dB ... 8 dB 0 mi ... 3.11 mi
(0 km ... 5 km)

1.0 dB/km 800 MHz×km

-MM/LC... MM 1310 nm 62.5/125 µm 0 dB ... 11 dB 0 mi ... 2.49 mi
(0 km ... 4 km)

1.0 dB/km 500 MHz×km

-SM/LC... SM 1310 nm 9/125 µm 0 dB ... 13 dB 0 mi ... 15.53 mi
(0 km ... 25 km)

0.4 dB/km 3.5 ps/(nm×km)

-SM+/LC... SM 1310 nm 9/125 µm 10 dB ... 29 dB 15.53 mi ... 40.39 mi
(25 km ... 65 km)

0.4 dB/km 3.5 ps/(nm×km)

-LH/LC... SM 1550 nm 9/125 µm 10 dB ... 29 dB 29.20 mi ... 64.62 mi
(47 km ... 104 km)

0.25 dB/km 19 ps/(nm×km)

-LH/LC... SM 1550 nm 9/125 µm 10 dB ... 29 dB 14.29 mi ... 86.99 mi
(55 km ... 140 km)

0.18 dB/km

c

c. With ultra-low-loss optical fiber.

18 ps/(nm×km)

Table 5: Fiber port 100BASE-FX (SFP fiber optic Fast Ethernet Transceiver)

Installation MACH104

Release

08

01/2019

41

Product code
M-SFP-...

Mode

a

a. MM = Multimode, SM = Singlemode, LH = Singlemode Longhaul

Wave length Fiber System

attenuation

Example for F/O
cable length

b

b. Including 3 dB system reserve when compliance with the fiber data is observed.

Fiber
attenuation

BLPc/Dispersion

c. Using the bandwidth-length product is inappropriate for expansion calculations.

-SX/LC... MM 850 nm 50/125 µm 0 dB ... 7.5 dB 0 mi ... 0.34 mi

(0 km ... 0.55 km)

3.0 dB/km 400 MHz×km

-SX/LC... MM 850 nm 62.5/125 µm 0 dB ... 7.5 dB 0 mi ... 0.17 mi

(0 km ... 0.275 km)

3.2 dB/km 200 MHz×km

-MX/LC... MM 1310 nm 50/125 µm 0 dB ... 12 dB 0 km ... 1.5 km 1.0 dB/km 800 MHz×km

-MX/LC... MM 1310 nm 62.5/125 µm 0 dB ... 12 dB 0 mi ... 31.06 mi

(0 km ... 50 km)

1.0 dB/km 500 MHz×km

-LX/LC... MM 1310 nm

d

d. With F/O adapter compliant with IEEE 802.3-2002 Clause 38 (single-mode fiber offset-launch mode conditioning patch cord).

50/125 µm 0 dB ... 10.5 dB 0 mi ... 0.34 mi

(0 km ... 0.55 km)

1.0 dB/km 800 MHz×km

-LX/LC... MM 1310 nm

e

e. With F/O adapter compliant with IEEE 802.3-2002 Clause 38 (single-mode fiber offset-launch mode conditioning patch cord).

62.5/125 µm 0 dB ... 10.5 dB 0 mi ... 0.34 mi
(0 km ... 0.55 km)

1.0 dB/km 500 MHz×km

-LX/LC... SM 1310 nm 9/125 µm 0 dB ... 10.5 dB 0 mi ... 12.43 mi
(0 km ... 20 km)

f

f. Including 2.5 dB system reserve when compliance with the fiber data is observed.

0.4 dB/km 3.5 ps/(nm×km)

-LX+/LC... SM 1310 nm 9/125 µm 5 dB ... 20 dB 8.70 mi ... 26.10 mi
(14 km ... 42 km)

0.4 dB/km 3.5 ps/(nm×km)

-LH/LC... LH 1550 nm 9/125 µm 5 dB ... 22 dB 14.29 mi ... 49.71 mi
(23 km ... 80 km)

0.25 dB/km 19 ps/(nm×km)

-LH+/LC LH 1550 nm 9/125 µm 15 dB ... 30 dB 44.12 mi ... 67.11 mi
(71 km ... 108 km)

0.25 dB/km 19 ps/(nm×km)

-LH+/LC LH 1550 nm 9/125 µm 15 dB ... 30 dB 44.12 mi ... 79.54 mi
(71 km ... 128 km)

0.21 dB/km
(typically)

19 ps/(nm×km)

Table 6: F/O port 1000BASE-FX (SFP fiber optic Gigabit Ethernet Transceiver)

42

Installation MACH104

Release

08

01/2019

Product code
M-SFP-BIDI...

Mode

a

a. MM = Multimode, SM = Singlemode, LH = Singlemode Longhaul

Wave lengthTXWave lengthRXFiber System

attenuation

Example for F/O
cable length

b

b. Including 3 dB system reserve when compliance with the fiber data is observed.

Fiber
attenuation

Dispersion

Type A LX/LC EEC SM 1310 nm 1550 nm 9/125 µm 0 dB ... 11 dB 0 km ... 12.43 mi

(0 km ... 20 km)

0.4 dB/km 3.5 ps/(nm×km)

Type B LX/LC EEC SM 1550 nm 1310 nm 9/125 µm 0 dB ... 11 dB 0 mi ... 12.43 mi

(0 km ... 20 km)

0.25 dB/km 19 ps/(nm×km)

Type A LH/LC EEC LH 1490 nm 1590 nm 9/125 µm 5 dB ... 24 dB 14.29 mi ... 49.71 mi

(23 km ... 80 km)

0.25 dB/km 19 ps/(nm×km)

Type B LH/LC EEC LH 1590 nm 1490 nm 9/125 µm 5 dB ... 24 dB 14.29 mi ... 49.71 mi

(23 km ... 80 km)

0.25 dB/km 19 ps/(nm×km)

Table 7: F/O port (bidirectional Gigabit Ethernet SFP transceiver)

Installation MACH104

Release 08 01/2019

43

6.5 Power consumption/power output

MACH104device Maximum

power consumption

Maximum
power output

MACH104-20TX-F... 35 W 119 Btu (IT)/h
MACH104-20TX-FR... 35 W 119 Btu (IT)/h
MACH104-20TX-F-4-PoE..., with 4 ×

Class 0 Powered-Device connected

110 W 170 Btu (IT)/h

44

Installation MACH104

Release 08 01/2019

7 Scope of delivery, order numbers and

accessories

 MACH104-20TX-F...

 MACH104-20TX-FR...

 MACH104-20TX-F-4-PoE...

 Accessories and order numbers

Note: Note that products recommended as accessories may have
characteristics that do not fully correspond to those of the respective
product. This may limit their possible usage in the overall system.

Number Article

1 × General safety instructions
1× Device
1 × 2-pin terminal block for signal contact
2 × Brackets with fastening screws (pre-mounted)
1 × Casing feet, stick on
1 × Non-heating appliance cable (Euro model)

Number Article

1 × General safety instructions
1× Device
1 × 2-pin terminal block for signal contact
2 × Brackets with fastening screws (pre-mounted)
1 × Casing feet, stick on
2 × Non-heating appliance cable (Euro model)

Number Article

1 × General safety instructions
1× Device
1 × 2-pin terminal block for signal contact
2 × Brackets with fastening screws (pre-mounted)
1 × Casing feet, stick on
1 × Non-heating appliance cable (Euro model)

MACH104device Order number

MACH104-20TX-F-L2P 942 003-001
MACH104-20TX-FR-L2P 942 003-101
MACH104-20TX-F-4-PoE-L2P 942 003-201
MACH104-20TX-F-L3P 942 003-002
MACH104-20TX-FR-L3P 942 003-102
MACH104-20TX-F-4-PoE-L3P 942 003-202

Installation MACH104

Release 08 01/2019

45

Name Order number

AutoConfiguration AdapterACA21-USB (EEC) 943 271-003
AutoConfiguration AdapterACA11 943 751-001
Terminal cable 943 301-001
2-pin terminal block (50 pieces) 943 845-010
Bracket for fastening the casing 943 943-001
Bracket, long (+ 1.97 in (50 mm)), for fastening the casing (extra) 943 943-101
Network management software Industrial HiVision 943 156-xxx
OPC Server software HiOPC 943 055-001

Gigabit Ethernet SFP transceiver Order number

M-SFP-TX/RJ45 943 977-001
M-SFP-TX/RJ45 EEC 942 161-001
The following operating conditions apply to twisted pair transceivers:

 Usable with:

- HiOS as of software version 03.0.00

- Classic Switch software, as of software version 04.1.00.

- HiSecOS as of software version 01.2.00
Do not use with the following devices:

- SPIDER II- MSP/MSM

- EES

 Longer RSTP switching times and link loss detection times compared to twisted pair ports

provided by the device directly.

 Not applicable for combo and Fast Ethernet ports.
 Only support of the autonegotiation mode including autocrossing.

M-SFP-SX/LC 943 014-001
M-SFP-SX/LC EEC 943 896-001
M-SFP-MX/LC EEC 942 108-001
M-SFP-LX/LC 943 015-001
M-SFP-LX/LC EEC 943 897-001
M-SFP-LX+/LC 942 023-001
M-SFP-LX+/ LC EEC 942 024-001
M-SFP-LH/LC 943 042-001
M-SFP-LH/LC EEC 943 898-001
M-SFP-LH+/LC 943 049-001
M-SFP-LH+/LC EEC 942 119-001
SFP-GIG-LX/LC

a

a. You find further information on certifications on the Internet at the Hirschmann product

pages (www.hirschmann.com).

942 196-001

SFP-GIG-LX/LC EEC

a

942 196-002

46

Installation MACH104

Release 08 01/2019

Fast Ethernet SFP transceiver Order number

M-FAST SFP-TX/RJ45 942 098-001
M-FAST SFP-TX/RJ45 EEC 942 098-002
The following operating conditions apply to twisted pair transceivers:

 Usable with:

- HiOS as of software version 03.0.00

- for PRP ports on RSP devices, as of software version 02.0.01

- for PRP ports on EES devices, as of software version 02.0.02

- Classic switch software as of software version 08.0.00

- HiSecOS as of software version 01.2.00

 Longer RSTP switching times and link loss detection times compared to twisted pair ports

provided by the device directly.

 Not applicable for combo ports.
 Not applicable for ports which support only Gigabit Ethernet.
 To set autocrossing manually is currently not possible.

M-FAST SFP-MM/LC 943 865-001
M-FAST SFP-MM/LC EEC 943 945-001
M-FAST SFP-SM/LC 943 866-001
M-FAST SFP-SM/LC EEC 943 946-001
M-FAST SFP-SM+/LC 943 867-001
M-FAST SFP-SM+/LC EEC 943 947-001
M-FAST SFP-LH/LC 943 868-001
M-FAST SFP-LH/LC EEC 943 948-001
SFP-FAST-MM/LC

a

a. You find further information on certifications on the Internet at the Hirschmann product

pages (www.hirschmann.com).

942 194-001

SFP-FAST-MM/LC EEC

a

942 194-002

SFP-FAST-SM/LC

a

942 195-001

SFP-FAST-SM/LC EEC

a

942 195-002

Bidirectional Gigabit Ethernet SFP transceiver Order number

M-SFP-BIDI Type A LX/LC EEC 943 974-001
M-SFP-BIDI Type B LX/LC EEC 943 974-002
M-SFP-BIDI Type A LH/LC EEC 943 975-001
M-SFP-BIDI Type B LH/LC EEC 943 975-002
M-SFP-BIDI Bundle LX/LC EEC (type A + B) 943 974-101
M-SFP-BIDI Bundle LH/LC EEC (type A + B) 943 975-101

Installation MACH104

Release 08 01/2019

47

8 Underlying technical standards

The device generally fulfills the technical standards named in their current
versions.
The device has an approval based on a specific standard exclusively if the
approval indicator appears on the device casing.
If your device has a shipping approval according to Germanischer Lloyd or
DNV GL, you find the respective approval mark printed on the device label.
You will find out whether your device has other shipping approvals on the
Hirschmann website under www.hirschmann.com in the product information.

Name

CSA 22.2 No. 60950-1 Information Technology Equipment – Safety – Part 1: General

Requirements

EN 61000-6-2 Electromagnetic compatibility (EMC) – Part 6-2: Generic

standards – Immunity for industrial environments

EN 55032 Electromagnetic compatibility of multimedia equipment –

Emission Requirements
FCC 47 CFR Part 15 Code of Federal Regulations
EN 60950-1 Information technology equipment – Safety – Part 1: General

requirements
IEEE 802.1D MAC Bridges (switching function)
IEEE 802.1Q Virtual LANs (VLANs, MRP, Spanning Tree)
IEEE 802.1w Rapid Reconfiguration
IEEE 802.3 Ethernet
UL 60950-1 Information technology equipment – Safety – Part 1: General

requirements

Table 8: List of the technical standards

48

Installation MACH104

Release 08 01/2019

A Further support

Technical questions

For technical questions, please contact any Hirschmann dealer in your area
or Hirschmann directly.

You find the addresses of our partners on the Internet at http://

www.hirschmann.com.

A list of local telephone numbers and email addresses for technical support
directly from Hirschmann is available at https://

hirschmann-support.belden.com.

This site also includes a free of charge knowledge base and a software
download section.

Hirschmann Competence Center

The Hirschmann Competence Center is ahead of its competitors on three
counts with its complete range of innovative services:

 Consulting incorporates comprehensive technical advice, from system

evaluation through network planning to project planning.

 Training offers you an introduction to the basics, product briefing and user

training with certification.
You find the training courses on technology and products currently
available at http://www.hicomcenter.com.

 Support ranges from the first installation through the standby service to

maintenance concepts.

With the Hirschmann Competence Center, you decided against making any
compromises. Our client-customized package leaves you free to choose the
service components you want to use.

Internet:

http://www.hicomcenter.com

Installation MACH104

Release 08 01/2019

49