Hioki L9788 Instruction Manual

L9788,L9788-01

スイッチ付きリード

TEST LEAD WITH REMOTE
CONTROL SWITCH
取扱説明書 / Instruction Manual
2011 年 4 月 改訂 1 版 Printed in Japan L9788A980-01 11-04H
L9788,L9788-01
点検・保守
隙間のないように しっかり差し込む
単位:mm
先端拡大図
ø3.0
ø1.8
35
16
MEASURE キー
キャップ
取り外すとき
点検
本器がお手元に届きましたら、輸送中において異常または破損がないか点検し てからご使用ください。万一、破損あるいは仕様どおり動作しない場合は、お 買上店(代理店)か最寄りの営業所にご連絡ください。
保守・サ-ビス
本器の汚れをとるときは、柔らかい布に水か中性洗剤を少量含ませて、軽く
ふいてください。ベンジン、アルコール、アセトン、エーテル、ケトン、シ ンナー、ガソリン系を含む洗剤は絶対に使用しないでください。変形、変色 することがあります。
故障と思われるときは、お買上店(代理店)か最寄りの営業所にご連絡ください。
輸送中に破損しないように梱包し、故障内容も書き添えてください。輸送中
の破損については保証しかねます。
安全について
この取扱説明書には本器を安全に操作し、安全な状態に保つのに要する情報や 注意事項が記載されています。本器を使用する前に下記の安全に関する事項を よくお読みください。
この機器は測定方法を間違えると人身事故や機器の故障につながる 可能性があります。取扱説明書を熟読し、十分に内容を理解してか ら操作してください。万一事故があっても、弊社製品が原因である 場合以外は責任を負いかねます。
安全記号
使用者は、取扱説明書内の マークのあるところは、必ず読み 注意する必要があることを示します。 使用者は、機器上に表示されている マークのところについ
て、取扱説明書の マークの該当箇所を参照し、機器の操作を してください。
取扱説明書の注意事項には、重要度に応じて以下の表記がされています。
操作や取扱いを誤ると、使用者が死亡または重傷につながる危険 性が極めて高いことを意味します。
操作や取扱いを誤ると、使用者が傷害を負う場合、または機器を 損傷する可能性があることを意味します。
製品性能および操作上でのアドバイス的なことを意味します。
感電事故を防ぐため、本器の先端で電圧のかかっているラインを
短絡しないでください。
対地間最大定格電圧は AC600 V 以下です。大地に対してこの電圧
を超える測定はしないでください。本器を破損し、人身事故にな ります。
感電・短絡事故を避けるため、本器を接続する前に各機器の電源 を OFF にしてください。
油、薬品、溶剤などが付着する場所で使用しないでください。 付着す ると、ひび割れの原因となり、感電事故や故障を引き起こす恐れが あります。
この機器は室内用に設計されています。安全性を損なわないで -10 ℃~ 50 ℃の温度まで使用できます。
本器をぬらしたり、ぬれた手で測定しないでください。感電事故 の原因になります。
本器の損傷を防ぐため、運搬および取扱いの際は振動、衝撃を避 けてください。特に、落下などによる衝撃に注意してください。
断線による故障を防ぐため、本器の付け根を折ったり引っ張った りしないでください。
本器の先端はとがっているため危険です。けがのないよう、取扱 いには十分注意してください。
使用方法
使用前の確認
使用前には、保存や輸送による故障がないか、点検と動作確認をしてから使用 してください。点検箇所としては、ピンの動作、先ピンの緩みなどがありま す。故障を確認した場合は、お買上店(代理店)か最寄りの営業所にご連絡く ださい。
感電事故を防ぐため、ケーブル内部から白色部分(絶縁層)が露出 していないか確認してください。ケーブル内部の色が露出している 場合は、使用しないでください。損傷がある場合は、感電事故にな るので、お買い上げ店(代理店)か最寄の営業所にご連絡ください。
仕様
L9788-01 L9788 スイッチ付きリードと EARTH 側リードのセットです。
機能
使用温湿度範囲
使用場所
保存温湿度範囲
最大定格
キャップ装着時
キャップ未装着時 対地間最大定格電圧 600 V
最大定格電流
耐電圧
ケーブル長
質量
付属品 取扱説明書
適合規格 L9788, L9788-01 HIOKI 3490, IR4000シリーズ専用です。
スイッチ:手持ち部にリモートコントロール用
MEASURE キー
ライト :手持ち部先端に照明用ライト
-10 ℃~ 50℃、90%rh 以下(結露なきこと) 屋内、汚染度 2、高度 2000 m 以下
-20 ℃~ 60℃、90%rh 以下(結露なきこと)
対地間最大定格電圧 600 V 測定カテゴリⅢ 予想される過渡過電圧 6000 V
測定カテゴリⅡ 予想される過渡過電圧 4000 V
2 A(連続) AC5312 V50/60 Hz(金属部 - 樹脂部間)
15 秒間、感度電流 1 mA
1000 mmL9788) 約 1200 mmL9788-01 EARTH 側リード)
60 gL9788)、約 130 g(L9788-01
安全 EN61010
各部の名称
はじめに
このたびは、 きリードセットをご選定いただき、誠にありがとうございます。この製 品を十分にご活用いただき、末長くご使用いただくためにも、取扱説明 書はていねいに扱い、いつもお手元に置いてご使用ください。
概要
L9788 スイッチ付きリードは、手持ち部分に MEASURE キー、先端に ライトを搭載した絶縁抵抗計 3490IR4000 シリーズ用テストリード です。 このテストリードをご使用いただくことにより、測定中、LIN E側テス トリードを持っている右手で測定を開始することが可能となります。 さらに、ライトがついていますので暗所での作業も容易になります。 また、ピン先の長さが長いため、ブレーカを測定するときに、ほとん どのブレーカでカバーを外すことなく測定でき、先端が細くなってい ますので、ピン先をコンセントに挿入することができます。
HIOKI L9788
スイッチ付きリード、
L9788-01
スイッチ付
その他の記号
してはいけない行為を示します。
測定カテゴリ(過電圧カテゴリ)について
本器は CAT III に適合しています。 測定器を安全に使用するため、IEC61010では測定カテゴリとして、使用する 場所により安全レベルの基準を CATⅠ~ CAT Ⅳで分類しています。
CATⅠ:コンセントからトランスなどを経由した機器内の二次側の電気回路 CATⅡ:コンセントに接続する電源コード付き機器(可搬形工具・家庭用電気
製品など)の一次側電路。 コンセント差込口を直接測定する場合は CAT Ⅱです。
CATⅢ:直接分電盤から電気を取り込む機器(固定設備)の一次側および分電
CATⅣ:建造物への引込み電路、引込み口から電力量メータおよび一次側電流
カテゴリの数値の小さいクラスの測定器で、数値の大きいクラスに該当する場 所を測定すると重大な事故につながる恐れがありますので、絶対に避けてくだ さい。
本器を安全にご使用いただくために、また機能を十二分にご活用いただくため に、下記の注意事項をお守りください。
盤からコンセントまでの電路
保護装置(分電盤)までの電路
使用上の注意
L9788 を絶縁抵抗計に接続した場合も、絶縁抵抗計の MEASURE キーは有効となっています。L9788 を絶縁抵抗計に接続した状態で、 絶縁抵抗計のMEASUREキーを押しても試験電圧が出力されますの でご注意ください。
• L9788 のライトは、絶縁抵抗計のメータライトと連動します。
• MEASURE キーは本体の活線警告表示と連動して赤色に点灯します。
テストリードの先端金属ピンには、取り外し可能なキャップが装着されてい
ます。短絡事故を防ぐため、測定カテゴリ CAT Ⅲで測定するときは、必ず キャップをつけて使用してください。CAT Ⅰと CAT Ⅱで測定するときは、 キャップを外して使用してください。測定カテゴリについては、取扱説明書 の「測定カテゴリについて」を参照してください。
キャップを装着して測定する場合、キャップを損傷しないように注意してく
ださい。測定中に不用意にキャップが外れた場合などは、感電事故を防ぐた め取り扱いには十分注意してください。
1. 絶縁抵抗計の電源が OFF になっていることを確認します。
2.
本器のプラグを、絶縁抵抗計の
3.
始業前点検
a. テストリードの先端をショートします。 b. 絶縁抵抗計を絶縁抵抗レンジに設定します。 c. L9788 の MEASURE キーを押すと測定値が 0 を表示すること、L9788
MEASURE キーが、絶縁抵抗計の活線警告表示と連動して赤色に点灯 することを確認してください。
d. 絶縁抵抗計の LIGHT キーを押すと、L9788 先端のライトが点灯すること
を確認してください。(同時に絶縁抵抗計のメータライトも点灯します)
(本器を使用する前に、下記事項を必ず確認してください。)
LINE
端子側に根元までしっかり差し込みます。
4. テストリードを測定対象に接続します。
5. 絶縁抵抗計の設定をします。
6. MEASURE キーを押と測定を開始します。
先ピン ( オプション ) の交換方法
L9788 の先端のピンが磨耗したり、折れた場合には交換することができます。 交換に必要な先ピン(L9788-90)は HIOKI代理店からお買い求めください。
1. 絶縁抵抗計の電源を OFF にし、本器を取り外します。
2. ソケットをスパナ(7 mm幅)で回し取り外します。
先ピンを取り外します。
3. L9788 の先ピンを新しいものに交換し、ソケットをスパナで回して本器に
取り付けます。(締付けトルク:0.3 N
4. 動作確認をします。既知の測定対象物を測定し、抵抗値が正確であるか確
認してから使用してください。
m
Introduction

L9788, L9788-01

TEST LEAD WITH REMOTE
CONTROL SWITCH

Instruction Manual

April 2011 Revised edi tion 1 Printed in Japan
L9788A980-01 11-04H
φ
1.8
φ
3.0
35
Enlarged view of pin
16
Sleeve
Unit: mm
MEASURE key
Plug the test lead securely into the Insulation Resistance Tester.
Yes
No
Turn to remove
Thank you for purchasi ng the HIO KI Mo del L9788 TEST LEAD WITH REMOTE CONTROL SWITCH,L9788-01 COMPLETE TEST LEADS WITH REMOTE CONTROL SWITCH. To obtain maximum performance from the instrument, please read this manual first, and keep it handy for future reference.
Overview
The L9788 T est Lead With Remote Control Switch is a test lead for use with a Model 3 490 and IR4000 se ries Insula tion Resistan ce T ester, equipped with a MEASURE key at the grip and a light at the front. With this te st lead, users ca n start the m easurem ent by using the test lead on the LINE side with their right hand. Furthermore, the light at the front makes it easier to carry out work in dark areas. The pin tip is also slightly longer tha n usual, making it po ssible to
measure breakers without removing the breaker covers in most cases, and thinner, allowing it to be inserted into an electrical outlet.
Inspection and Maintenance
Initial Inspection
When you receive the in strumen t, ins pect it c arefu lly to e nsur e that no damage occurred during shipping. If damage is evident, or if it fails to oper ate according to the specific ations, contact your dealer or Hioki representative.
Maintenance and Service
• To clean the instrument, wipe it gent ly with a soft cloth moist­ened with water or mild det ergent. Never use solvents such as benzene, alcohol, acetone, ether, ketones, thinners or gasoline, as they can deform and discolor the case.
• If the instrument seems to be malfunctioning, contact your dealer or Hioki representative.
• Pack the instrument so that it will not sustain damage during shipping, and include a description of existing damage. We can­not accept responsibility for damage incurred during shipping.
Safety
This manual contains information and warnings essential for
safe operation of the instrument and for maintaining it in safe op­erating condition. Before using it, be sure to ca refully read the following safety precautions.
Mishandling this instrument during use could result in injury or death, as well as damage to the instrument. Be certain that you understand the instructions and precau­tions in the manual before use. We disclaim any respon­sibility for accidents or injuries not resulting directly from instrument defects.
Safety Symbol
In the manual, the symbol indicates particularly important information that the user should read before using the instrument. The symbol printed on the instrument indicates that the user should refer to a corresponding topic in the manual (marked with the
symbol) before using the relevant function.
The following symbols in this manual indicate the relative impor­tance of cautions and warnings.
Indicates that incorrect operati on pres en ts an extreme hazard that could resul t in s erious injur y or de ath to the user.
Indicates that incorrect operation presents a possibility of injury to the user or damage to the instrument.
Indicates advisory items related to performance or cor­rect operation of the instrument.
Other Symbol
Indicates a prohibited action.
Measurement categories (Overvoltage categories)
This instrument complies with CAT III safety requirements. To ensure safe operation of measurement instruments, IEC 61010 establishes sa fety standards for v arious electrical envi­ronments, categorized as CAT I to CAT IV, and called measure­ment categories. CAT I: Secondary electri cal circuits c onnected to a n AC elec-
trical outlet through a transformer or similar device.
CA T II: Primary electrical circuits in equipment connected to an
AC electrical outlet by a power cord (portable tools, household appliances, etc.). CAT II covers directly measuring electrical outlet receptacles.
CAT III: Primary electrical circuits of heavy equipment (fixed in-
stallations) connected directly to the distribution panel, and feeders from the distribution panel to outlets.
CAT IV: The circuit from the service drop to the service en-
trance, and to the power meter and primary overcurrent
protection device (distribu t io n panel). Using a measurement instrument in an environment designated with a higher-numbered category than that for which the instru­ment is rated could resu lt in a severe accident, and must be carefully avoided.
Parts Names
Usage Notes
Follow these precautions to ensure safe operation and to obtain the full benefits of the various functions.
• To avoid electrical shock, be careful to avoid shorting live lines with the pin.
• The maximum rated voltage between input terminals and ground is 600 VAC. Attempting to measure voltages exceeding these limits with respect to ground could damage the instrument and result in personal injury.
• To avoid shock and short circuits, turn off all power before connecting leads.
Do not use the instrument where it may be exposed to oil, chemicals, or solvents. Contact with these substances may cause cracking in the instrumen t, resulting in dam­age or electric shock.
• This instr ument is de signe d for use indoors . It ca n b e oper­ated at temperatures between -10 and 50°C without degrad­ing safety.
• Do not allow the instrument to get wet, and do not take mea­surements with wet hands. This may cause an electric shock.
• To avoid damage to the instrument, protect i t from physical shock when transporting and handling. Be especially careful to avoid physical shock from dropping.
• To avoid breaking the leads, do not bend or pull them.
• The ends of the leads are sharp. Be careful to avoid injury.
Procedure
Preliminary Checks
Before using the instrument the first time, verify that it operates normally to ensure that no damage occurred during storage or shipping. Points to check include the pin operation and whether the pin and cable lock are loose. As loose screwi ng o f the c able loc k and o ther comp onents can result in damage, be sure to tighten them securely before use. If you find any damage, contact your dealer or Hioki representative.
To prevent an electric shock accident, confirm that the white portion (insulation layer) inside the cable is not exposed. If a color inside the cable is exposed, do not use the cable. Using the instrument in such conditions could cause an electr ic shock, so contact your dealer o r Hioki representative for repair.
The Insulation Resistance Tester’s MEASURE key will still be available even when this test lead is connected to the Insulation Resistance Tester. When connected to the Insulation Resis­tance Tester, take note that a test voltage will be discharged even when the MEASURE key of the Tester is pressed.
• The light of this instrument is connected with the Insulation Resistance Tester’s Meter Light.
• The MEASURE key is connected with the Live circuit indicator and will light up as red.
• Removable sleeves are attached to the metal pins at the ends of the test leads. To prevent a short circuit accident, be sure to use the test leads with the slee ve s attach ed whe n per for m ­ing measurements in the CAT III a measurement category. Remove the sleeves from the test leads when performing measurements in the CAT I and CAT II measurement catego­ries.For details on measurement categories, see “Measure­ment categories” in the instruction manual.
• When performing measurements with the sleeves attached, be careful to avoid damagi ng the sleeves. If the slee ves are inadvertently removed during measurement, be especially careful in handling the test leads to avoid electric shock.

1.Confirm that the pow er of the Insul ation Resi stance Tester is turned off.

2.Plug the test lead securely into the LINE terminal of the Insu­lation Resistance Tester.
3.Before Starting (Before using the test leads, be sur e to con­duct the following safety checks.) a. Short circuit the tips of the test leads.
b. Turn the function switch of the Insulation Resistance Tester
to one of the Insulation Resistance Measurement functions.
c. Press the MEASURE key on the L9788 Test Leads and
confirm that:
• 0 Ω is indicated on the Insulation Resistance T ester; and
• Upon pressing the MEASURE key on the L9788, the MEA­SURE key lights up in red.
d. When pressing the LIGHT key on the Insulation Resistance
T ester , the light at the tip of the L9788 T est Leads turns ON.

4.Connect the test lead to the object to be measured.

5.Carry out settings on the Insulation Resistance Tester.

6.Press the MEASURE key to start the measurement.

Specific ations
Model L9788-01 is a set of Model L9788 and EARTH side lead. Functions Switch: MEASURE key for remote control grip
Operating temperature and humidity
Operating Environment Indoors, Altitude up to 2000 m (6562 feet),
Storage temperature and humidity
Maximum rated
• Sleeves attached Maximum rated voltage to earth 600 V
• Sleeves removed
• Maximum rated current Dielectric strength 5312 V AC, 50/60 Hz (Metallic part - Resin part),
Cable length Model L9788: Approx. 1000 mm (39.37”)
Mass Model L9788: Approx. 60g (2.1 oz.)
Accessory Instruction manual Applicable Standards Safety EN61010 Model L9788, L9788-01 is provided exclusively for the Hioki Model 3490 and
IR4000 series.
Light : Light at the tip of the at the grip
°C to 50°C (14°F to 122°F), 90%RH or less
-10 (no condensation)
Pollution degree 2
-20°C to 60°C (-4 (no condensation)
Measurement category III Anticipated transient overvoltage 6000 V
Maximum rated voltage to earth 600 V Measurement category II Anticipated transient overvoltage 4000 V
2A (continuous)
15sec, Current sensitivity 1 mA
Model L9788-01: Approx. 1200 mm (47.24”)
Model L9788-01: Approx. 130g (4.6 oz.)
°F to 140°F), 90%RH or less
Replacing the Pin
The pin at the front of the test lead can be replaced when it has worn away or is damaged. Replacement pins (Model L9788-90) are available at any Hioki dealer.

1.Turn off the power of the Insulation Resistance Tester and disconnect the test leads.

2.Rotate the sock et with a spanner (7 mm width) to remove it. Remove the front pin.

3.Exchange the L 9788 front pin with a new one, turn the socket with a spanner and attach it to the test lead. (tightening torque : 0.3Nm)

4.Check the pe rforman ce. Me a­sure an object with a known resistance. Make sure that the measured resistance is cor­rect before using the L9788.
Loading...