
DT4900
通信パッケージ(USB)
COMMUNICATION PACKAGE (USB)
取扱説明書 / Instruction Manual
2012 年 11 月 初版 Printed in Japan
DT4900A980-00 12-11H
ご使用にあたっての注意
1. 通信アダプタを本体に取り付ける
2. USB ケーブルを通信アダプタに接続する
3. USB ケーブルをコンピュータに接続する
コンピュータに接続 (USB)
データ送信
本体を制御
1
2
3
通信アダプタ
USB ケーブル
本体に接続
1. 一般仕様の動作環境を満たしていることを確認し、CD-R を
CD-ROM ドライブに装着します。
2. USB ドライバをインストールします。
CD-R の [\USB Driver] 内にあるドライバをインストール
してください。
3. [\Appli\setup.exe] を実行します。画面の手順に従ってイ
ンストールしてください。
( 操作方法は CD-R の [\Manual] 内にあるマニュアルを参
照してください )
1. デバイスマネージャを開きます。
• WindowsXP の場合
[ コントロールパネル ]-[システム ]-[ハードウエア ]
-[デバイスマネージャ ]
• WindowsVista の場合
[ スタート ]-[コントロールパネル ]-[ハードウェア
とサウンド ]-[デバイスマネージャ ]
• Windows7 の場合
[ スタート ]-[コントロールパネル ]-[システムとセ
キュリティ ]-[デバイスマネージャー ]
2. ポート(COMとLPL)の項のProlific USB-to-Serial Bridge
(COMX) の "X" が COM ポート番号です。
接続方法
通信方式
ご使用の前に下記事項をご確認ください。
• 本製品 は日置電機株式会社の著作物です。
• 対応測定器のデータを処理する目的以外で本製品の一部または全
部を複製、複写、改変することは法律で禁じられております。
• 本製品は改良のため予告なく変更、バージョンアップすることがあ
ります。
• 本製品を引用し書籍を刊行する場合、弊社による事前の承諾が必要
です。また、「HIOKI」の商標の使用はできません。
• 弊社はいかなる場合においても、お客様が本製品を使用した運用結
果に関して、一切の責任を負うものではありません。
CD-R の取り扱いについて
• ディスクに指紋などの汚れを付けないようにするため、また印刷が
かすれないようにするため、お取り扱いの際は必ずディスクの縁を
持つようにしてください。
• ディスクの記録面には決して手を触れないようにしてください。ま
た堅いものの上に直接置かないようにしてください。
• ディスクのレーベル表示が消える可能性がありますので、ディスク
を揮発性アルコールや水にぬらさないようにしてください。
• ディスクのレーベル面に文字を記入するときは、先がフェルトの油
性ペンをご使用ください。ディスクを傷つけ記録内容を破損する危
険性がありますので、ボールペンやその他の先の堅いペンは使用し
ないでください。また粘着性ラベルも使用しないでください。
• ディスクがゆがんだり記録内容が破損する危険性がありますので、
直射日光や高温多湿の環境にディスクをさらさないでください。
• ディスクのシミやホコリ、指紋などを取り除く場合には、柔らかく
て乾いた布または CD クリーナーをお使いください。常に内側から
外側に向けてぬぐうようにし、決して輪を描くようには拭かないで
ください。また、研磨剤や溶剤系クリーナーは使用しないでくださ
い。
• この CD-R のご使用にあたってのコンピュータシステム上のトラブ
ル、および製品の購入に際してのトラブルについて、弊社は一切の
責任を負いません。
本体とコンピュータを付属の USB ケーブルで接続します。
USB ケーブルを接続するときは、コネクタの向きに注意して
ください。
インストール方法
• USB インタフェース
• 仮想 COM ポート使用
(詳細は CD-R の [\Manual] 内にあるマニュアルを参照してく
ださい。)
はじめに
このたびは、HIOKI DT4900 通信パッケージ(USB)をご選
定いただき、誠にありがとうございます。この製品を十分にご
活用いただき、末長くご使用いただくためにも、取扱説明書は
ていねいに扱い、いつもお手元に置いてご使用ください。
登録商標について
• Windows、WindowsXP、WindowsVista、Windows7、
Internet Explorerは米国マイクロソフト社の登録商標です。
• その他の製品名は各社の商標または登録商標です。
概要
本製品は、コンピュータを使って対応測定器のデータ処理をす
るソフトウェアです。
点検
本器がお手元に届きましたら、輸送中において異常または破損
がないか点検してからご使用ください。万一、破損あるいは仕
様どおり動作しない場合は、お買上店(代理店)か最寄りの営
業所にご連絡ください。
1234
• 故障と思われるときは、お買上店(代理店)か最寄りの営業
所にご連絡ください。
• 最新バージョンは、弊社ホームページからダウンロードでき
ます。
仕様
一般仕様
CD-R 1 枚
本製品
付属品
対応測定器 HIOKI DT4281, DT4282
動作環境
(DT4281,
DT4282
通信ソフト )
数値の形式は、小数点の記号には ” . ”(ピリオド)、桁区切り記号には
” , ”(カンマ)を使用してください。
機能仕様 (DT4281, DT4282 通信ソフト)
機能 測定器の設定値を変更 , 測定データを記録
最大取扱データ数 1,048,576 データ
記録時間間隔 00:00:01 ~ 99:99:99
記録 CSV 形式
• USB ドライバ
• アプリケーション
• 通信コマンド取扱説明
• USB ケーブル...............................................1
• 通信アダプタ..................................................1
• 取扱説明書 .......................................................1
本体 : CPU 動作クロック 1 GHz 以上
メモリ : 512 MB 以上
OS : Windows XP(SP2 以上) /
Vista(SP1 以上) / 7
ディスプレイ : 解像度 1024×768 以上
ハードディスク : 空き容量 30 MB 以上
通信インタフェース : USB 2.0(仮想 COM ポート)
本製品は仮想 COM ポートを使用します。COM ポートの設定
について、USB ポートに割り当てられる COM ポート番号は使
用されるコンピュータによって変わります。
次の方法で割り当てられた COM ポート番号を確認してくださ
い。

Introduction
DT4900
COMMUNICATION PACKAGE (USB)
Instruction Manual
November 2012 Edition 1 Printed in Japan
DT4900A980-00 12-11H
1. Attach the communication adapter to the supported
instrument.
2. Connect the USB cable to the communication adapter.
3. Connect the USB cable to the computer.
Connect to computer (USB).
Tran smits data.
Controls the supported instrument.
1
2
3
Communication
adapter
USB cable
Connect to the supported instrument.
1. Ver ify t hat the computer to be used sati sfi es the oper -
ating environment requirement s o utlined in t he general specifications and insert t he CD into the computer's
CD-ROM drive.
2. Install the USB driver.
Install the driver found in the [\USB Driver] folder on
the CD.
3. Launch [\Appli\setup.exe] and follow the instructions
on your screen to install the driver.
(For more information about the installation procedure, refer to the instruction manual in the [\Manual]
folder on the CD.)
1. • WindowsXP
[Control Panel] - [System] - [Hardware] [Device Manager]
• WindowsVista
[Start] - [Control Panel] - [Hardware and Sound] [Device Manager]
• Windows7
[Start] - [Control Panel] - [System and Security] [Device Manager]
2. The x in "Prolific USB-to-S erial Bridge (COMx)" in the
list of ports (COM and LPL) indicates the COM port
number.
Thank you for purchasing the HIOKI Model DT49 00 Communication Package (USB). To obtain maximum performance from the product, please read this manual first, and
keep it handy for future reference.
Trademarks
• Windows, WindowsXP, WindowsVista, Windows7 and
Internet Explorer are registered trademarks of Microsoft
Corporation in the United S t ates and/or other countries .
• Other trademarks are the property of their respective
owners.
Usage Notes
Before Using the software, please read these notes carefully .
• HIOKI E.E. CORPORATION is the author of DT4900.
• Except for the purposes of processing data from supported instruments, copying, reproduction, or amendment in whole or in part of DT4900 is prohibited by law.
• For the purpose of product development, the DT4900 is
subject to upgrading without notice.
• To publish material referencing the DT4900, the prior
consent of Hioki is required. The trade mark "HIOKI"
may not be used.
• Hioki cannot accept any responsibility whatever for the
results of a customers operation of the DT4900.
CD
• Always hold the disc by the edges, so as not to make
fingerprints on the disc or scratch the printing.
• Never touch the recorded side of the disc. Do not place
the disc directly on anything hard.
• Do not wet the disc with volatile alcohol or water, as
there is a possibility of the label printing disappearing.
• To write on the disc label surface, use a spirit-based felt
pen. Do not use a ball-point pen or hard-tipped pen,
because there is a danger of scrat ching t he surfac e and
corrupting the data. Do not use adhesive labels.
• Do not expose the disc directly to the sun's rays, or keep
it in conditions of high temperature or hum idity, as there
is a danger of warping, with consequent loss of data.
• To remove dirt, dust, or fingerprints from the disc, wipe
with a dry cloth, or use a CD cleaner. Always wipe from
the inside to the outside, and do no wipe with circular
movements. Never use abrasives or solvent cleaners.
• Hioki shall not be held liable for any problems with a
computer system that arises from the use of this CD, or
for any problem related to the purchase of a Hioki product.
• CPU clocked at 1 GHz or greater
Minimum PC
Requirement
(Communication software for
Model DT4281
and DT4282)
For numerical settings, please adjust the settings on your PC so
that the period [.] is used to represent the decimal point, and the
comma [,] is used to separate groups of thousands.
• 512 MB memory or more
• Windows XP (SP2 or later) / Vista (SP1 or
later) / 7 operational system
• Display: 1024 × 768 dots or more
• 30 MB hard disk space or more
• Communication interface: USB 2.0 (virtual
COM port)
Functional specifications
(Communication software for Model DT4281 and DT4282)
Functions
Maximum
number of data
points
Record time
interval
Save format CSV data format
Changing instrument settings, saving measurement data
1,048,576
00:00:01 to 99:99:99
Hardware Connection
Connect the supported instrument to the computer with
the included USB cable, taking care to align the cable's
connector with the receptacle on the communication
adapter.
Software Installation
This product use s a virtual COM port. The COM port number
allocated to the USB port will vary with the computer on whic h
the software is used.
Use the following method to check the allocated COM port number.
Overview
The DT4900 is a software application for processing data
from supported instruments on a computer.
Inspection
When you receive the product, inspect it carefully to ensure that no damage occurred during ship ping. If damage
is evident, or if it fails to operate according to the specifications, contact your authorized Hioki distributor or reseller.
1234
• If the product seems to be malfunctioning, contact your
authorized Hioki distributor or reseller.
• The latest version can be downloaded from our web
site.
Specifications
General Specifications
One CD
• USB driver
Product
Accessories
Supported
instruments
•Application
• Communications command instruction manual
USB cable .............................................1
Communication adapter ........................1
Instruction manual ................................1
HIOKI Model DT4281 and DT4282
Communication Methods
• USB interface
• Use virtual COM port
(For more information, refer to the instruction manual in
the [\Manual] folder on the CD.)