
クランプオンセンサ
CLAMP ON SENSOR
取扱説明書/ Instruction Manual
2015年9
9298A980-10 15-09H
月改訂10版
Printed in Japan
9298
はじめに
このたびは、
とうございます。この製品を十分にご活用いただき、末長くご使用いただくため
にも、取扱説明書はていねいに扱い、いつもお手元に置いてご使用ください。
HIOKI 9298
クランプオンセンサ をご選定いただき、誠にありが
概要
本器は
100A
は電力ラインを切り離すことなく、活線状態で交流電流を測定できます。また、
操作、接続も簡単なため多方面での電流、電力測定にご使用いただけます。
(
弊社クランプオンパワーハイテスタ3166、3168用)
定格の交流電流対応の電流出力型クランプオンセンサです。本器
点検
本器がお手元に届きましたら、
てからご使用ください。万一、破損あるいは仕様どおり動作しない場合は、お
上店(代理店)か最寄りの営業所にご連絡ください。
輸送中
において異常または破損がないか点検し
買
使用前の確認
・使用前には、保存や輸送による故障がないか、点検と動作確認を
してください。故障を確認した場合は、お買上店(代理店)か最寄りの営業所
にご連絡ください。
・ケーブルの被覆が破れたり、金属が露出していないか、使用する前に確認して
ください。損傷がある場合は、感電事故になるので、お買上店(代理店)か
寄りの営業所にご連
絡ください。
してから使用
最
安全について
危険
この機器は
で出荷されています。測定方法を間違えると人身事故や機器の故障につな
がる可能性があります。また、本器をこの取扱説明書の記載以外の方法で
使用した場合は、本器が備えている安全確保のための機能が損なわれる可
能性があります。
取扱説明書を熟読し、十分に内容を理解してから操作してください。万一
事故があっても、弊社製品が原因である場合以外は責任を負いかねます。
■ 安全記号
この取扱説明書には本器を安全に操作し、安全な状態に保つのに要する情報や
注意事項が記載されています。本器を使用する前に下記の安全に関する事項を
よくお読みください。
■ この取扱説明書で使用している記号
取扱説明書の注意事項には、重要度に応じて以下の表記がされています。
注記
■ 測定カテゴリについて
本器は
測定器を安全に使用するため、
所により安全レベルの基準を
CAT
Ⅱ:コ
CATⅢ:直接分電盤から電気を取り込む機器(固定設備)の一次側および分電
CAT
Ⅳ:建造物への引込み
カテゴリの数値の小さいクラスの測定器で、数値の大きいクラスに該当する場
所を測定すると重大な事故につながる恐れがありますので、絶対に避けてくだ
さい。
カテゴリのな
事故につながる恐れがありますので、絶対に避けてください。
IEC 61010
注意や危険を示します。機器上にこの記号が表示されている
場合は、取扱説明書の該当箇所を参照ください。
交流(AC)を示します。
二重絶縁または強化絶縁で保護されている機器を示します。
活線状態の電路に着脱できることを示します。
危険
警告
注意
操作や取扱いを誤ると、使用者が死亡または重傷につながる危
険性が極めて高いことを意味します。
操作や取扱いを誤ると、使用者が死亡または重傷につながる可
能性があることを意味します。
操作や取扱いを誤ると、使用者が傷害を負う場合、または機器
を損傷する可能性があることを意味します。
製品性能および操作上でのアドバイス的なことを意味します。
CATIIIに適
ンセントに接続する電源コード付き機器(可搬形工具・家庭用電気
製品など)の一次側電路
コ
ンセント差込口を直接測定する場合は
からコンセントまでの電路
保護装置(分電盤)までの電路
い測定器で、
安全規格に従って、設計され、試験し、安全な状態
合しています。
IEC61010
CATⅡ~CATⅣで分類しています。
電路、引込み口から電力量メータおよび一次側電流
CAT
Ⅱ~
では測定カテゴリとして、使用する場
CATⅡです。
CATⅣの測定カテゴリを測定すると重大な
盤
ご使用にあたっての注意
本器を安全にご使用いただくために、また機能を十二分にご活用いただくため
に、下記の注意事項をお守りください。
危険
・短絡事故や人身事故を避けるため、クランプセンサは
の電路で使用してください。
・クランプセンサは、必ずブレーカの二次側に接続してください。ブレー
カの二次側は、万一短絡があっても、ブレーカにて保護します。一次側
は、電流容量が大きく、万一短絡事故が発生した場合、損傷が大きくなる
ので、測定しないでください。
AC 300 Vrms
以下
警告
・本器をぬらしたり、ぬれた手で測定しない でくださ い。感 電事故の 原因
になります。
・活線で測定するので、感電事故を防ぐため、労働安全衛生規則に定められ
ているように、電気用ゴム手袋、電気用ゴム長靴、安全帽等の絶縁保護具
を着用してください。
・測定範囲を超える電流を 長時間入力しな いでください 。本器を破損 する恐
れがあります。
注意
・ジョー先端部に異物等を挟んだり、ジョーの隙間に物を差し込んだりし
ないでください。センサ特性の悪化、開閉動作不具合の原因になります。
・直射日光や高温、多湿、結露するような環境下での、保存や使用はしない
でください。変形、絶縁劣化を起こし、仕様を満足しなくなります。
・本器の損傷を防ぐため、運搬および取扱いの際は振動、衝撃を避けてくだ
さい。特に、落下などによる衝撃に注意してください。本器を破損しま
す。
・使用しないときは、ジョーを閉じておいてください。開いたままの状態
にしておくと、ジョーの突き合わせ部にゴミや
原因になります。
ホコリが付
着し、故障の
注記
ト
ランスや大電流路など強磁界の発生している近く、また無線機など強電
界
の発生している近くでは、正確な測定ができない場合があります。
各部の名称と機能
BNCコネク
フェライトコ
タ
ア
ジョー
ロックツマ
ケーブル
ミ
測定方法
注意
・
BNCコネクタを引き抜くときは、必ずロックを解除してから、コネク
を持って引き抜いてください。ロックを解除せずに無理に引っ張った
り、ケーブルを持って引っ張るとコネクタ部を破損します。
・接続機器の電源が入った状態、または測定導体をクランプした状態で、
ネクタの抜
なります。
測定電流と出力電流の位相を
方向表示マークの矢印が負荷側に向くようにして、
先端が確実にかみ合わさっていることを確認してください。
差しをしないでください。本体およびセンサの故障の原因に
同位相
にするため、ジョーに表示されている電流
ほぼ中央
にクランプします。
タ
コ
電線 負荷側(
電源側(
1.
レバーがロックされている場合は、解除してください。
2. BNCコネクタを、
押し込み
3.
レバーを押しながらスライドさせ、導体をクランプしてください。
導体は1
4.
ジョー先端の接合部が確実に閉じていることを確認します。
5.ロックツマミ
SOURCE
ながら
本だけ、
)
3166、3168
右へ回してロッ
ほぼ中央
スライドさせ、ロックします。
を
電流入力端子のコネクタ・ガイド溝に合わせ、
にクランプしてください。
レバー
クします。
LOAD
)
電流方向表示マーク
負荷側へ向ける
仕様
確度保
証条件
定格一次電流
定格二次電流
二次電流振幅確
二次電流位相確
振
幅周波数
(確度からの偏差)
外部磁界の
導体位置の影響 ±
最
大入力電流
耐電圧
対地間最
電
使用温湿度範囲
保存温湿度範囲
使用場所 高度2,000 m
適
測定可能
コ
外形寸法
質
付属
大定格
圧
合規格 安全性
導体径 φ
ード長
量
品 取扱説明書1部、マークバンド6個(3組)
確度保証期間
調整後確度保証期間:1年間
ジョー部開閉
*3166、3168
わせによる。
確度保証温湿度範囲:23℃±5℃,80% rh
AC 100 A
AC 100 mA
度 ±
0.5 % rdg.±0.2 %f.s.(f.s.は3166、3168の各
とする)(45~
度 ±1°
特性
影響 約
以内(
40 Hz~5kHz±1%
0.1 A(400 A/m
0.5%
以内
45~66 Hz
AC 4290 V rms 1
(ジョー-手持ち部間、ジョー-出力コネクタ間)
AC 300 V rms
0~50℃、
-10~60℃、
(予想される
EMC EN61326
15 mm
約
3m
約
46W×135H×21D mm
約
230 g
において
80% rh
EN61010
:1年
間
回数 :1万回まで
クランプオンパワーハイテスタとの組み合
66 Hz,
ジョー中心にて)
45 Hz~5kHz
以下
80% rh
まで、屋内
過渡過電圧
)
以内
の交流磁界にて)
130 A連続(周囲温度50℃)
分間
以下(結露しないこと)
以下(結露しないこと)
測定カテゴリⅢ、
4000 V
)
以下
汚染度
レンジ
2
保守・サービス
■ 本器のクリーニング
本器の汚れをとるときは、柔らかい布に水か中性洗剤を少量含ませて、軽く拭い
てください。
■ サービス
・故障と思われるときは、お買上店(代理店)か最寄りの営業所にご連絡くださ
い。
・
輸送中
に破損しないように梱包し、故障内容も書き添えてください。
破損については保証しかねます。
輸送中
の

9298
CLAMP ON SENSOR
Instruction Manual
September
Warranty
Warranty malfunctions occurring under conditions of normal use in
conformity with the Instruction Manual and Product Precautionary
Markings will be repaired free of charge. This warranty is valid for
a period of one (1) year from the date of purchase. Please contact
the distributor from which you purchased the product for further
information on warranty provisions.
Introduction
Thank you for purchasing the HIOKI 9298 CLAMP ON SENSOR. To
obtain maximum performance from the product, please read this
manual first, and keep it handy for future reference.
Overview
The 9298 is current output type clamp on sensor, which is applicable
to 100A AC current measurements. The instrument can be used to
measure alternating current on a live power line without the need to
cut the wire. Easy operation and connection make them useful for
measuring alternating current and power in various fields.
(for use with HIOKI 3166 and 3168 CLAMP ON POWER HiTESTER)
Inspection
When you receive the product, inspect it carefully to ensure that no
damage occurred during shipping. If damage is evident, or if it fails to
operate according to the specifications, contact your dealer or Hioki
representative.
Preliminary Checks
Before using the product the first time, verify that it operates normally
to ensure that the no damage occurred during storage or shipping. If
you find any damage, contact your dealer or Hioki representative.
Before using the product, make sure that the insulation on the cables
is undamaged and that no bare conductors are improperly exposed.
Using the product in such conditions could cause an electric shock, so
contact your dealer or Hioki representative for repair.
2015 Revised edition 10 Printed in Japan
9298A980-10
15-09H
Safety
DANGER
This product is designed to comply with IEC 61010 Safety
Standards, and has been thoroughly tested for safety prior to
shipment. However, mishandling during use could result in injury
or death, as well as damage to the product. However, using the
product in a way not described in this manual may negate the
provided safety features.
Be certain that you understand the instructions and precautions in
the manual before use. We disclaim any responsibility for
accidents or injuries not resulting directly from product defects.
Safety symbols
This manual contains information and warnings essential for safe
operation of the product and for maintaining it in safe operating
condition. Before using the product, be sure to carefully read the
following safety notes.
Indicates cautions and hazards. When the symbol is
printed on the product, refer to a corresponding
topic in the Instruction Manual.
Indicates AC (Alternating Current).
Indicates a double-insulated device.
Indicates that the instrument may be connected to or
disconnected from a live circuit.
The following symbols in this manual indicate the relative importance
of cautions and warnings.
Indicates that incorrect operation presents an
DANGER
WARNING
CAUTION
NOTE
Measurement categories
This product complies with CAT III safety requirements.To ensure safe
operation of measurement products, IEC 61010 establishes safety standards
for various electrical environments, categorized as CAT II to CAT IV, and
called measurement categories. These are defined as follows.
CAT II: Primary electrical circuits in equipment connected to an AC electrical
outlet by a power cord (portable tools, household appliances, etc.)
CAT II covers directly measuring electrical outlet receptacles.
CAT III: Primary electrical circuits of heavy equipment (fixed installations)
connected directly to the distribution panel, and feeders from the
distribution panel to outlets.
CAT IV: The circuit from the service drop to the service entrance, and to the
power meter and primary overcurrent protection device (distribution
panel).
Using a measurement product in an environment designated with a highernumbered category than that for which the product is rated could result in a
severe accident, and must be carefully avoided.
Use of a measurement instrument that is not CAT-rated in CAT II to CAT IV
measurement applications could result in a severe accident, and must be
carefully avoided.
extreme hazard that could result in serious injury or
death to the user.
Indicates that incorrect operation presents a
significant hazard that could result in serious injury
or death to the user.
Indicates that incorrect operation presents a
possibility of injury to the user or damage to the
product.
Advisory it ems related to performance or correct
operation of the product.
Notes on Use
Follow these precautions to ensure safe operation and to obtain the full
benefits of the various functions.
DANGER
To avoid short circuits and potentially life-threatening
hazards, never attach the clamp to a circuit that operates
at more than the 300 Vrms.
Clamp sensor should only be connected to the secondary
side of a breaker, so the breaker can prevent an accident if
a short circuit occurs. Connections should never be made
to the primary side of a breaker, because unrestricted
current flow could cause a serious accident if a s hort
circuit occurs.
WARNING
To avoid electric shock, do not allow the product to get
wet, and do not use it when your hands are wet.
To avoid electric shock when measuring live lines, wear
appropriate protective gear, such as insulated rubber
gloves, boots and a safety helmet.
Note that the product may be damaged if current
exceeding the selected measurement range is applied for a
long time.
CAUTION
Keep the jaws tips and jaws slits free from foreign objects,
which could interfere with clamping action.
Do not store or use the product where it could be exposed to
direct sunlight, high temperature or humidity, or condensation.
Under such conditions, the product may be damaged and
insulation may deteriorate so that it no longer meets
specifications.
To avoid damage to the product, p rotect it from vibration or
shock during transport and handling, and be especially careful
to avoid dropping.
Keep the jaws closed when not in use, to avoid accumulating
dust or dirt on the mating jaw surfaces, which could interfere
with clamp performance.
NOTE
Accurate measurement may be impossible in the presence of strong
magnetic fields, such as near transformers and high-current
conductors, or in the presence of strong electromagnetic fields such
as near radio transmitters.
Part Names
BNC connector
Cable
Ferrite core
Jaws
Measurement Procedure
CAUTION
When disconnecting the BNC connector, be sure to release the
lock before pulling off the connector. Forcibly pulling the
connector without releasing the lock, or pulling on the cable,
can damage the connector.
To prevent damage to the product and sensor, never connect
or disconnect a sensor while the power is on.
In order to make the phases of the measurement and output c urrents
the same, clamp the jaws of the sensor onto the conductor so that
the current direction on the clamp points in the direction of the load,
and so that the conductor is approximately centered between the
jaws. Make sure that the tips of jaws are fully closed.
Line
SOURCE
1. Slide the lock button into the unlocked position when the lever is
locked.
2. Align the BNC connector with the connector guide notch on the
current input connector. While pushing the connector in, turn it to
the right to lock it.
3. Open the jaws, and clamp the sensor onto the conductor.
4. Make sure that only one conductor is in the jaws.
5. Make sure that the tips of jaws are fully closed.
LOAD
Current direction arrow
in the direction of the
load
Specifications
Conditions of guaranteed accuracy
Accuracy is guaranteed for one year at 23
80%RH,andincombinationwiththe3166and3168CLAMPON
POWER HiTESTER. (Opening and Closing of the Sensor: Maximum
10000 times)
Guaranteed accuracy period after adjustment made by Hioki :1year
Rated primary current 100 A AC
Rated secondary current 100 mA AC
Secondary current
amplitude accuracy
Secondary current
phase accuracy
Amplitude frequency
charactristics
Effect of external
magnetic field
Effect of conductor position Within 0.5%
Maximum input current 130 A continuous at 45 to 66 Hz (50 , 122 )
Dielictric strength 4290 V rms AC 1 minute, jaw - hand-held
Maximum rated voltage to earth Max. 300 V AC
Operating temperature
and humidity range
Storage temperature
and humidity range
Location for use Altitude up to 2000 m (6562 feet), Indoors
Standards applying Safety EN61010 Measurement Category
Diameter of measurable conductor 15 mm dia. (0.59")
Cord length Approx. 3 m (9.8 feet)
External dimensions Approx. 46W 135H 21D mm (1.8"W
Mass Approx. 230 g (8.1 oz.)
Accessories Instruction manual, Mark band 6 (3 sets)
0.5 %rdg. 0.2 %f.s.
(f.s. : ranges of the 3166 and 3168)
(45 to 66 Hz, at the clamp jaw center)
Within 1 (45 Hz to 5 kHz)
Within 1% at 40 Hz to 5 kHz
(Deviation from accuracy)
Approx. 0.1 A
(in an AC magnetic field of 400 A/m)
portion, jaw - output connector
0to50 (32to122 ), Max. 80 %RH
(no condensation)
-10to60 (14to140 ), Max. 80 %RH
(no condensation)
III Pollution Degree 2 (anticipated transient
overvoltage 4000 V)
EMC EN61326
2.3 "H 0.7 "D) (excluding protrusions)
5 (73 9 ) and Max.
Maintenance and Service
Cleaning the unit
To clean the product, wipe it gently with a soft cloth moistened with
water or mild detergent. Never use solvents such as benzene,
alcohol, acetone, ether, ketones, thinners or gasoline, as they can
deform and discolor the case.
Service
If the product seems to be malfunctioning, contact your dealer or
Hioki representative.
Pack the product carefully so that it will not be damaged during
shipment, and include a detailed written description of the problem.
Hioki cannot be responsible for damage that occurs during
shipment.