Hioki 9263 User Manual

I

ntroduction

S

N

1

C

K

F

r

S
c

2

3

･
･
･

S

F

R

4

5

6

･

･

･

･

･

N

H

Thank you for purchasing this HIOKI "9263 SMD
TEST FIXTURE." To get the maximum performance
from the unit, please read this manual first, and keep
this at hand.

afety

This Instruction Manual provides information and
notes essential for operating this equipment in a
safe manner and for maintaining it in safe operating
condition. Before using this equipment, be sure to
carefully read the following safety notes.

Indicates that incorrect operation

CAUTIO

NOTE

presents possibility of injury to the
user or damage to the equipment.

Denotes items of advice related to
performance of the equipment or to
its correct operation.

. Overview

This HIOKI 9263 SMD TEST FIXTURE can be
directly connected to the measurement terminals
(UNKNOWN) of the HIOKI LCR and Z HiTESTERs
for testing a SMD component. The component can
be clamped with a single knob action.

ixing leve

onnecting terminals

. Connecting the Test Fixture

Plug the fixture into the measurement terminals
(UNKNOWN) of the tester, with the product name up.

Fasten it in place with the left and right fixing levers.

. Fixing the Samples

Put the sample (figure below) on the clamping
portion, and clamp it by turning the knob.

NOTE

Samples whose width are 1 to 10 mm can be
clamped.

Be careful to keep dirt away from the clamping
portion.

Make sure the sample is firmly clamped. If not,
accurate measurements cannot be obtained.

ample

. Open and Short Circuit Compensation

To enhance the accuracy of measurement, perform
the open and short circuit compensation.

NOTE

The method of operation depends on the tester to
which the test fixture is connected. Refer to the
Instruction Manual for the tester.

Open circuit compensation

Turn the knob to open the high and low clamping
portions (with no connection between the two ends
of the clamping) in width of the sample to be
measured.

Short circuit compensation

Turn the knob to short the high and low clamping
portions.

. Specifications

Compatible instrument 3502, 3522, 3531
Measurement frequency DC to 5 MHz

range
Maximum apply voltage ±40 V DC
Widthofsampletobe 1to10mm

tested
Residual resistance 5 mΩ max. (at 100 Hz)

(short-circuited)
Floating capacitance 1 pF max. (at 5 MHz)

between terminals
Dimensions 86(W)×22(H)×40(D) mm

Mass 100 g
Operating temperature 0 to 40℃, 80% R.H. or less

and humidity range with no condensation
Srorage temperature -10 to 55℃, 80%R.H. or less

and humidity range with no condensation
Location for use Elevation of up to 2000 m

(excluding protrusions)

indoor

. Notes on Using the Test Fixture

Be careful to avoid dropping the unit or subjecting
to other mechanical shock.

Do not use the unit in direct sunlight, dusty
conditions, or in the presence of corrosive gases.

Gently wipe dirt from the surface of the unit with a
soft cloth moistened with a small amount of water.
Do not try to clean the unit using cleaners
containing organic solvents such as benzine or
thinners. They may cause discoloration or
damage.

If the unit has gotten seriously wet, oily, or dusty,
stop using it and send it for service at an approved
HIOKI service facility.

For using the tester to which the test fixture is
connected, refer to Instruction Manual of the
tester.

CAUTIO

For applying a DC voltage, refer to the
Instruction Manual of the tester.

ample

lamping portion

nob

emove

ix

EAD OFFICE

81 Koizumi, Ueda, Nagano 386-11, Japan
FAX. [phone] / TEL. [phone]
E-mail: [e-mail]