8'x8' Soft Top Steel Gazebo
WARNING:
Fabric meets CPAI-84 specification for flame resistance. It is Not
Fire Proof. The fabric will burn if left in continuous contact with
any flame source. The application of any harsh chemicals to the
fabric may render the flame-resistant properties ineffective.
Always read and follow the instructions before use. When assembling
and using this product, basic safety precautions must always be folÂlowed to reduce risk of personal injury and damage to the product or
surroundings.
Be sure to keep all children and pets away from assembly area. Some
parts contain sharp edges. Wear protective gloves when handling these
items. It is recommended that, for safety issues, at least 2 people as
semble the gazebo. It may take to 90 minutes to assemble this gazebo.
It is important to schedule enough time to complete the assembly. You
should not leave the unit unattended if it is not fully assembled, even if
it is already anchored to the ground. You should begin the assembly no
less than 6 feet from any permanent structures such as fences,a garage,
a house, overhanging branches, electrical wires or laundry lines. You
must assemble your unit on level ground or a platform.
The unit must be anchored to the ground with proper anchors. Failure
to do so may risk it blowing away.
Check that all screws are tight before and during usage. Do not place
any type of heat conductor or source under, or within 5 feet of the unit
including, but not limited to, a barbeque or space heater.
The gazebo is designed to provide shade only. Do not use this gazebo
in strong wind and rain. Wind and rain can damage the gazebo and
could result in injury to you and others. It is recommended that the Canopy
be removed during strong winds and stormy conditions.
Check all available parts. Before assembling the gazebo, check to make
sure you have all the parts listed in the Parts List.
Parts List
A
B
C
D
E
F
G
H
J
K
Description
Screen
Beam
Slanting Beam
Slanting Beam
Bottom Tube
Middle Beam
Top Connector
Hook
Corner Shelf
Small Canopy
Big Canopy
Sketch
QTY
4
4
4
4
4
1
1
4
1
1
M
Anchor
8
Assembly
Step 1
B
D
B
Fig. 2
Fig. 1
A
Fig. 1
A
B
Fig. 2
Fig. 3
Fig. 3
B
A
A
Bolt Hole
D
B
B
inside
Fig. 3
A
A
Fig.1: Open Screen (A).
Fig.2: Insert Slanting Beam Bottom Tube (D) to corner of Screen (A). Repeat the above step
for each corner.
Fig.3: Insert Beam(B) to the top tube of Screen (A). Repeat the above step for each corner.
Assembly
Step 2
Fig. 6
Fig. 4
B
B
E
Fig. 5
E
C
C
Fig. 7
E
C
B
Fig. 6
B
F
Fig. 4 Fig. 5
C
E
F
C
C
C
E
F
G
Fig. 6
Fig. 7
C
D
A
B
Fig.4: Insert Slanting Beam (C) to Top Connector (F) long tube . Insert Middle Beam (E)to Top
Connector (F) short tube.
Fig.5:Put Hook (G) the Top Connector (F).
Fig.6: Insert Slanting Beam (C) to Slanting Beam Bottom Tube (D) till you see the push pin out from
the tube. Repeat the above step for each Slanting Beam (C) to Slanting Beam Bottom Tube (D).
Fig.7: Insert Middle Beam (E) to Beam (B), Repeat the above step for each Middle Beam (E) and
Beam (B).
E
Assembly
Step 3
Fig. 8
J
Fig. 9
K
H
H
Fig. 10
Fig. 11
Fig. 8 Fig. 9
C
J
Fig.8: Insert Slanting Beam (C) to Small Canopy (J) corner. Repeat the above step for each corner.
Fig.9: Using the Big Canopy velcro to attach the screen (A) 's standing pole.
Fig.10: Hanging Triangle Shelf (H) to Screen (A). Repeat the above step for each Screen (A).
Fig.11: Insert 2PCS Anchor(M) to each Screen (A).
Any questions on assembly or parts, please contact: customerservice@e2e-corp.com
velcro
K
A
Fig. 10
Fig. 11
H
A
M
Made in china
Loading...