HIO HIOO1125 Installation & Assembly

Page 1
10'x10' Soft Top Steel Gazebo with Netting
Page 2
WARNING:
Fabric meets CPAI-84 specification for flame resistance. It is Not Fire Proof. The fabric will burn if left in continuous contact with any flame source. The application of any harsh chemicals to the fabric may render the flame-resistant properties ineffective.
Always read and follow the instructions before use. When assembling and using this product, basic safety precautions must always be fol­lowed to reduce risk of personal injury and damage to the product or surroundings.
Be sure to keep all children and pets away from assembly area. Some parts contain sharp edges. Wear protective gloves when handling these items. It is recommended that, for safety issues, at least 2 people as semble the gazebo. It may take to 90 minutes to assemble this gazebo.
It is important to schedule enough time to complete the assembly. You should not leave the unit unattended if it is not fully assembled, even if it is already anchored to the ground. You should begin the assembly no less than 6 feet from any permanent structures such as fences,a garage, a house, overhanging branches, electrical wires or laundry lines. You must assemble your unit on level ground or a platform.
The unit must be anchored to the ground with proper anchors. Failure to do so may risk it blowing away.
Check that all screws are tight before and during usage. Do not place any type of heat conductor or source under, or within 5 feet of the unit including, but not limited to, a barbeque or space heater.
The gazebo is designed to provide shade only. Do not use this gazebo in strong wind and rain. Wind and rain can damage the gazebo and could result in injury to you and others. It is recommended that the Canopy
and Sidewall be removed during strong winds and stormy conditions.
Check all available parts. Before assembling the gazebo, check to make sure you have all the parts listed in the Parts List.
Page 3
PARTS LIST
A1
A2
B1
B2
C
D1
D2
G
H
Description
Screen
Screen
Cross Beam
Cross Beam
U Shape Bracket
w/steel plate
Roof Tube
Roof Tube
E
F
Roof Tube
Top Connector
Top Hook
Triangle Shelf
Sketch QTY
4 pcs
4 pcs
4 pcs
4 pcs
4 pcs
4 pcs
4 pcs
4 pcs
1 pc
1 pc
4 pcs
AA
BB
CC
DD
EE
FF
J
K
L
Small Roof Cover
Big Roof Cover
Mosquito Netting
Bolt
Bolt
Bolt
Bolt
Anchor
Wrench
M6 x 15mm
M6 x 30mm
M6 x 40mm
M6 x 48mm
1 pc
1 pc
4 pcs
4 pcs
4 pcs
16 pcs
12 pcs
8 pcs
2 pcs
Page 4
Assembly
Step 1
Fig.1
A2
B1
A1
B2
B2
A1
B1
A2
A2
B1
Fig.2
Fig.3
B2
A1
B2
B1
A1
A2
Fig.1
DD
A2
Fig.2
CC
A1
A2
B1
C
CC
CC
B2
A1
Fig.3
B1
Bolt Hole
inside
Fig.1: Using 3xBolt(DD) to connect top/middle/bottom for Screen (A1) & Screen (A2).Repeat the above step for each Screen (A1) & Screen (A2) . Fig.2: Using Bolt (CC) to connect Cross Beam (B1)& Screen (A2) or connect Cross Beam (B2) & Screen (A1).Using Bolt (CC) to connect(C) and Screen(A1) or (A2). Repeat the above step for each corner. Fig.3: Insert Cross Beam (B2) to Cross Beam (B1) till you see the push pin out from the tube. Repeat the above step for each Cross Beam( B2) and Cross Beam (B1).
B2
Page 5
Assembly
Step 2
F
Fig.5
D1
E
Fig.6
D1
Fig.4
D2
D1
E
Fig.6
D1
D2
Fig. 4
D2
E
D2
F
Fig. 5
D1
F
D1
E
G
Fig.4: Insert Hook (G) into the Top Connector (F). Fig.5: Connect Roof Tube (D1) & Top Connector (F) long tube, Connect Roof Tube (E) & Top Connector (F) short tube. Fig.6: Insert Roof Tube (D1)to Roof Tube (D2) till you see the push pin out from the tube. Repeat the above step for each Roof Tube ( D1)and Roof Tube (D2).
D1
E
Page 6
Assembly
Step 3
Fig.8
E
D2
Fig.7 Fig.8
D2
BB
C
D1
AA
D2
D2
E
Fig.8
Fig.7
E
B2
Fig.7: Insert Roof Tube (D2) to U Shape Bracket (C). Using Bolt (BB) to connect Roof Tube (D2) and U Shap Bracket (C) . Repeat the above step for each Roof Tube ( D2). Fig.8: Using Bolt (AA) to connect Roof Tube (E) and Cross Beam (B2).
Page 7
Assembly
Step 4
D1 & D2
J & K
Fig. 9
Fig. 9
H
Fig. 10
Fig. 10
B1 / B2
L
Fig. 9
Velcro
J
K
L
H
Fig. 11
Fig. 12
Fig. 11 Fig. 12
H
EE
Fig.9: Pull the corner of Small Roof Cover (J), and insert Roof Tube (D1) to this corner. Pull the corner of Big Roof Cover (K), and insert Roof Tube (D2) to this corner. Repeat the above step for each corner. Fig.10: Attach the Mosquito Netting (M) Velcro to Cross beam (B1/B2). Fig.11: Hanging Triangle Shelf (H) to Screen (A1& A2). Repeat the above step for each Screen (A1& A2). Fig.12: Insert each Anchor(EE) to each Screen (A1) or Screen (A2)
Any questions on assembly or parts, please contact: customerservice@e2e-corp.com
Made in china
Loading...