HIO HIOO1105 Owner Manual

ASSEMBLE INSTRUCTION

10FT X 10FT ALUM DOUBLE ROOF GAZEBO

Any questions on assembly or parts,

please contact:customerservice@e2e-corp.com

Safety Information

WARNING: Keep all ﬂame and heat sources away from this tent fabric. This tent is made with fabric that meets CPAI-84 speciﬁcation for

ﬂame resistance. It is not ﬁre proof. The fabric will burn if left in continuous contact with any ﬂame source. The application of any foreign substance to the tent fabric may render the ﬂame-resistance properties ineffective.

When assembling and using this product, basic safety precautions must alawys be followed to reduce the risk of personalWARNING: injury and damage to product or surroundings.

WARNING: This gazebo is NOT a permanent structure and is designed for sunshade and privacy only.

The gazebo should only be used in ideal weather conditions. You MUST completely disassemble the gazebo prior to any extreme weather such as heavy thunder storms, hurricanes and/or ice/hail storms. Failure to do so may result in structural or property damage.

Always install the gazebo on level ground utilizing the ground stakes provided for stability. It is not recommended to

ice or hail storms.

CAUTION:

permanently anchor this gazebo to a hard surface such as a wood deck or concrete ﬂoor.

CAUTION: Gazebo roof is weather resistant but may leak during precipitation. It is recommended to remove the roof boards if expecting

CAUTION: Keep all children and pets away from assembly area.

Begin assembly not less than 6 feet from any obstruction such as fence, garage, house, overhanging branches, clothes line or electrical wires. Some parts may contain sharp edges, wear protective gloves if necessary.

Care Instructions

Before using, wipe with a clean, dry cloth. Do not use bleach or solvents. Treat the frame with liquid wax for maximum protection against UV light and salty, damp air. Clean the roof panels periodically with a mild soap and water. Do not use harsh chemical cleaners as this will damage the panel ﬁnish.

or loose nuts or bolts.

Please properly tighten all hardware and perform periodic inspections during usage for cracked welds

2

Pre-Assembly

PLANNING ASSEMBLY

It will take at least two people about 90 minut es to complete the assembly process. A rubber mallet and a free standing ladder are needed during the process.

IMPORTANT: Please count the number for each part before assembly.

PART LIST

NOTE: Parts not shown to actual size.

ITEM DESCRIPTION QTY. ILLUSTRATION

A

B

C

D

E

F

G

H

I

J

Right Cross Beam

Left Cross Beam

Netting Rail

Corner Post

Corner Roof Tube

Roof Sheet rail

Corner Roof Tube

4

8

4

K

M

N

Roof Rim

L

Small Support Crossbar With Hook & Loop

Roof Rim

Small Support Crossbar

4

20

12

3

Pre-Assembly

ITEM

O

Q

Y

Z EE

AA

Important: Do not remove the protective lm from the roof sheets until you are ready to attach them to the frame in Step 13 &18 .The surface with protective lm is the outer side.

U-Shaped Connector

Support Arm

Roof Sheet

QTY. ILLUSTRATIONDESCRIPTION ITEM DESCRIPTION ILLUSTRATION

4

8

4

BB

CC

DD

FF

Roof Sheet

Roof Mosquito Net

Mosquito Net

QTY.

4

1

4

HARDWARE LIST

NOTE: Hardware not shown to actual size.

ITEM DESCRIPTION QTY. ILLUSTRATION

W

P

R

S

Roof Hub Cover

T

U

V

X

U-Bracket

Roof Hub

Hook

Roof Spacer Bracket

Washer Plate

16

2

1

4

8

ITEM DESCRIPTION QTY. ILLUSTRATION

HH

JJ

KK

LL

MM Ground stake

NN Wrench

OO Wrench

Side End Cover

II

Self-tapping screw (M6x20)

Bolt (M6x15)

Bolt (M6x30) and nut

Self-tapping screw (M4x7)

16

96

28

24

32

4

1

GG

Corner End Cover

8

PP

4

Philips screw driver

1

Assembly

1. Attaching netting rails

LL

C

LL

A/B

LL

A C

LL

B C

Attach one netting rail (C) to each cross beam (A) & (B) with self-tapping screws (LL) using Philips screw driver (PP). Do not fully tighten all the self-tapping screws (LL) until the end of this step.

2. Assembling cross beams

II

P

II

P

II

P

A

II

P

A/B

II

P

B

Attach two U-brackets (P) to the top of each cross beam (A) & (B) with bolts (II) using wrench (NN).

5

Assembly

3. Assembling cross beams

A

O

B

A

O

B

II

B

Plug U-shaped connector (O) into each cross beam (B), using bolts (II) loosely secure them together until the end of this step. Repeat this for cross beam (A) until complete cross beams (A) & (B) are formed. Fully tighten all the bolts (II).

4. Erecting the main frame

B

A

B

D

B

A

D

II

A

B

II

D

B

II

Stand the corner post (D) up. Attach the B side of the cross beam to the outside right corner of each corner post (D) and attach the A side of the cross beam to the outside left corner of each corner post (D) with bolts (II) using wrench (NN).

6

Assembly

5. Attaching support arms

Q

II

Q

II

Adjust corner post (D) upright. Attach support arms (Q) to cross beams (A) / (B) and corner posts (D) with bolts (II) using wrench (NN).Do not fully tighten all the bolts (II) until the end of this step.

6. Assembling the roof frame

E

click!

E

R

E

R

Snap one corner roof tube (E) into each receiver of the roof hub (R) until you hear a click.

7

E

Assembly

7. Attaching the roof frame

E

JJ

D

Attach each corner roof tube (E) onto the bracket at the top pf each corner post (D) with bolts and nuts (JJ) using wrench (NN).

8. Attaching the roof sheet rails (F,G,H,I)

I

G

F

H

I

G

F

H

F

G

I

H

F

G

I

H

I/G

H/F

W

E

II

Attach roof sheet rails (I) and (H) onto the corner roof tube (E) with washer plates (W) and bolts (II) using wrench (NN). Do not fully tighten bolts until the end of step 20. Follow the above procedure to attach the roof sheet rails (G) and (F) onto the frame.

8

Assembly

9. Attaching roof sheet rails (F,G,H,I)

I

G

F

H

I

G

F

H

F

G

I

JJ

H

F

G

I

H

I/G

Attach roof sheet rails (I) and (H) onto the brackets on top of cross beams (A) / (B) respectively with bolts and nuts (JJ) using wrench (NN) and (OO). Follow the above procedure to attach the roof sheet rails (G) and (F) onto the frame.

10. Assembling the small roof frame

click!

J

R

J

R

J

Snap one corner roof tube (J) into each receiver of the roof hub (R) until you hear a click.

9

J

Assembly

11. Attaching the small roof frame

J

E

JJ

V

J

JJ

E

V

J

S

E

U

R

T

Fix the roof spacer brackets (U) under this last assembly by covering and screwing the roof hub cover (S) on. Lay down this assembly over the rst roof hub (R) tted with corner roof tube (E). Fix by using the hook (T) as shown. Fix other ends of corner roof tube (J) to the corner roof tube (E) by usingthe roof spacer brackets (V) and bolts and nuts (JJ)usingwrench (NN).

12. Insert small support crossbar

L

Insert small support crossbar with hook & loop (L) on pins of washer plates (W).

10

L

W

Assembly

13. Insert roof sheet for small roof

Y

J

Y

Insert one piece of roof sheet (Y) into the groove of corner roof tube (J). IMPROTANT: Before insert next roof sheet (Y) you should nish till the step 15. The roof sheet should insert one by one.

14. Insert roof rim for small roof

Y

K

J

Y

K

As illustrated, insert one piece of roof rim (K) at the end of last assembly roof sheet (Y) of small roof.

11

Assembly

15. Attaching end cover for small roof

Secure last assembly roof sheet (Y) by using corner end cover (GG) with self-tapping screw (KK). In order not to

GG

KK

GG

damage inserts, do not over tighten the screws. Repeat step 13 to step 15 to nish insert all four roof sheets (Y).

16. Install washer plate

G/F

X

II

X

As illustrated, install washer plate (X) to roof sheet rail (G) & (F) by using bolts (II).

12

Assembly

17. Attaching small support crossbars

N

X

Insert small support crossbars (N) on pins of washer plate (X) and (W) as shown.

N

W

N

18. Attaching roof sheets

DD

Z

CC

DD

BB

AA

Z

DD

CC

BB

AA

Z

CC

DD

Z

G

AA

BB

AA

BB

Insert one piece of roof sheet (Z) into the groove of roof tubes as shown. IMPROTANT: Before insert next roof sheet (AA) you should nish till the step 20. The roof sheet should insert one by one. Suggest nish insert one side and then next side

13

Assembly

19. Attaching roof rim

M

G

M

As shown, insert one piece of roof rim (M) at the end of last assembly roof sheet rail.

M

20. Attaching end cover for big roof

GG

HH

GG

HH

GG

HH

GG

HH

GG

KK

HH

KK

Secure last assembly roof sheet by using corner end cover (GG) and side end cover (HH) with self-tapping screw (KK). In order not to damage inserts, do not over tighten the screws. Repeat step 18 to step 20 to fnish insert all roof sheets (Z) (AA) (BB) (CC) (DD).

14

Assembly

21. Assembling roof mosquito net

EE

T

L

EE

Loosen the hook (T). Fix the roof mosquito net (EE) to the small roof. Tighten the hook (T) through the buttonhole on the roof mosquito net (EE).

22. Assembling mosquito net

FF

C

FF

D

FF

Hang up the mosquito net (FF) into the net hooks.

15

Assembly

23. Fix ground stakes

Use the ground stakes (MM) for ground xing.Insert the ground stake (MM) into any of the four holes at the bottom of the corner post (D). One corner post (D) one ground stake (MM).

D

MM

16