ATTENTION: THIS BOOKLET DOESN'T SUBSTITUTE THE OPERATION AND MAINTENANCE
MANUAL. IT’S NECESSARY TO READ CAREFULLY AND UNDERSTAND THE OPERATION AND
MAINTENANCE MANUAL BEFORE CARRYING OUT ANY MANOEUVRE WITH THE MACHINE.
QUICK INSTRUCTIONS FOR HINOWA LIGHTLIFT 15.70 & 13.70 PERFORMANCE
To start the machine battery cutter and main
key must be turned ON, than the remote control
emergency STOP button must be pressed and
released, as reminded by the icon here on the
right side. While all the emergency stop buttons
are released, engine or electric motor could be
ignited by pressing the relevant buttons on the
remote control (see picture above).
Miniexcavators – Undercarriages - Minidumpers – Skid Steer Loaders – Aerial Platforms
PRESS AND RELEASE
REMOTE CONTROL
EMERGENCY STOP
BUTTON
FIPE131521701
GASOLINE
ENGINE
WARM UP
EMERGENCY STOP
BUTTON
GRAVITY
EMERGENCY
DESCENT
AUTOMATIC
OUTRIGGERS
RETRACTION
LEFT TRACK
1st
CYLINDER
JIB
TURRET
ROTATION
RIGHT
TRACK
2
nd
CYLINDER
BASKET
ROTATION
(ONLY
LL15.70)
EXTENSION
BASKET
LEVELING
KEY
ELECTRIC
MOTOR
(START-
STOP)
THERMIC
ENGINE
(START-
STOP)
UNDERCARRIAGE
CLOSING (IF
AVAILABLE)
AUTOMATIC
STABILIZATION
UNDERCARRIAGE
WIDENING (IF
AVAILABLE)
ENGINE SPEED
SELECTOR
STABILIZERS
MANUAL OPERATING
SERVICE
MENU
SELECTOR
DISPLAY
PERMISSION OF AERIAL
PART OPERATION FROM
GROUND
MAIN KEY
Note1: On gasoline machine when the engine is cold, once it’s ignited, it’s
possible to warm it up pressing the “WARM UP” button on the remote control,
engine will run faster for 20 seconds.
TRACKS MOVEMENTS
All the outriggers must be raised from the ground
to move the tracks, otherwise the icon here on the
left side will be displayed. When jib is closed the
tracks could be moved operating from the ground
or form the basket, otherwise it’s possible to move
them even if jib is opened but in this case the
basket must be unloaded from its support
(LL1570), or be kept empty (LL1370) as reminded
by the picture here on the right side. In this case,
operator must drive from the ground keeping the
remote control on his hands.
To move the tracks press the red joystick on the remote control.
To open the jib (with basket off in the LL15) press the jib joystick.
To change the speed it has to be used button n.5 of remote
control.
Note2: Jib must be close to allow outriggers’ movements.
Note3: In particular conditions, tracks’ speed could be automatically limited by
speed control which prevent unsafe translations.
OUTRIGGERS MOVEMENTS
Machine must be perfectly closed and aligned to permit to
move the outriggers, so all the arms and the jib closed
and aerial part rotated as indicated by the alignment
arrows (see picture here aside). The MACHINE CLOSED
AND ALIGNED icon (see the picture below) indicates the
closed and aligned condition. To move the outriggers the
remote control could be in the basket support or operator
can keep it in his hands also standing at the ground.
AUTOMATIC STABILIZATION:
To stabilize the machine automatically the machine must be closed aligned.
Keeping pressed the green button (n.7) on the remote control the machine
starts the automatic stabilization procedure. That procedure will be complete
only when the display will show the OK with the MACHINE STABILIZED icon as
ALIGNMENT
ARROWS
MACHINE
CLOSED AND
ALIGNED
ICON ON THE
DISPLAY
PHOTOCELLS SYSTEM
DETECTS THE CLOSE
AND ALIGNED
CONDITION OF THE
MACHINE
UNLOAD
THE
BASKET
FROM ITS
SUPPORT
(LL1570)
RAISE THE
OUTRIGGERS
FROM THE
GROUND
BASKET MUST
BE EMPTY
(LL1370)
shown by the example that follows. The stabilization is the necessary condition
to allow aerial part movements.
MANUAL STABILIZATION:
It’s also possible to move the outriggers one by one pressing the blue button
(number 2) and following the indications given on the display. Once all the
outriggers are touching the ground, automatic stabilization remains the
recommended procedure.
AUTOMATIC OUTRIGGERS RETRACTION:
To put the machine in transport configuration aerial part must be closed and
aligned, then, keeping pressed the yellow button (number 1), all the outriggers
should be completely lifted until the end of their stroke.
AERIAL PART MOVEMENTS
To move the aerial part the remote control must
be positioned in its basket support. Aerial part
movements are possible only when machine is
stabilized and therefore when the MACHINE
STABILIZED icon appears in position 5 of the
display. If one stabilization condition is missing,
when a joystick is moved the display indicates the
missing condition with “FAIL” as follows.
ST”X” FAIL indicates that outrigger n. ”X” is not touching
the ground.
INCL FAIL means that the machine is not levelled within
the inclination clearance.
LOAD FAIL means that basket is overloaded (more than
230Kg into the basket so more than about 280 Kg read by
the input menu).
BASKET FAIL means that the remote control is not
properly placed on its basket support (it does not feel the
remote control support magnet).
PEDAL (OPTIONAL) FAIL means that pedal option is
activated and pedal is not properly pressed in order to
allow the movement.
AUTOST FAIL means auto-stabilization procedure not
complete properly.
OK
AUTOSTAB
WAIT
ST1 NO GND
ST2 NO GND
ST3 NO GND
ST4 NO GND
AUTS
STEP: 1
AUTOSTAB
WAIT
ST1 GND
ST2 GND
ST3 GND
ST4 GND
AUTS
STEP: 49
MACHINE
STABILIZED
ICON ON
THE
DISPLAY
BASKET FAIL
ST1 FAIL
INCL FAIL
After work is finished close carefully and completely all the arms and perfectly
align the turret looking at the yellow arrows. Than the outriggers could be
lifted and the tracks moved.
LIST OF DISPLAY ICONS
Tracks’
maximum
speed
12V
Battery
voltage low
Insert the
controller into its
place and stabilize
the machine from
the basket
Not allowed
movement,
open the 2nd
cylinder
Loading...