Page 1
Bulbs: 6 0W CA NDE LABRA
HAMLET
FR42868
A S S E M B L Y I N S T R U C T I O N S
Assembly of this fixture will be accomplished by first assembling the primary fixture
body, making all necessary electrical connections, hanging the fixture from the ceiling,
and then installing the crystals.
SA FE TY WARNING: Read wiring and grounding instructions [FRIS 18]
and any additional directions. Turn power supply off during installation. If new wiring
is required, consult a qualified electrician or local authorities for code requirements.
ST E P 1
1 To complete primary assembly of the fixture body, slip center column (1) along
supply wire and thread into top of fixture body (2) and tighten. - See Drawing 1.
2
Slip loop (3) along supply wire and thread onto top of c eenter column (1).
3
Thread bottom center stem (4) into coupler (5) located on the bottom of the
fixture in the center.
Slip center hole of bottom cap (6) onto bottom of center stem (4) and thread
4
on finial with ball (7) to secure cap (6) to fixture.
5
Fixture can be installed at this time.
S T E P 2 Refer to Hanging Instruction Sheet [FRIS19] to hang fixture.Then refer back
to this sheet to install crystals.
ST E P 3
1 Plesse reference Crystal and Rope installation instrutions to complete assembly.
.
[DRAWING 1]
3
1
2
5
4
6
7
06.01.13
Page 2
HAMLET
FR42868
CRYSTAL AND ROPE ACCENT INSTALLATION INSTRUCTIONS.
[DRAWING 1]
S T E P 1
1 Unpack all the crystal and rope strands, fixture should be lamped
accordingly, prior to crystal and rope strand installation.
2 Start by attaching a cystal strand (a) [small crystal at top] to one
of the holes in top cap (t). Attach bottom of crystal strand to the
corresponding hole in the top of the middle ring (m). Making sure
strand is perpenducular to middle ring.
3 Using top view guide below continue adding crystal strands (a) and
rope strands (b) to top half of fixures until completed.
4 The bottom strands of crystals (c) and rope strands (d) mirror the top
strands in location. Start by attaching a bottom crystal strand (c)
directly below top crystal strand (a), continue adding rope and
crystal strands in the same configuration as the top half of the fixture.
NOTE: use reference drawings below.
t
b
a
c
d
crystal and rope reference guide
m
TOP VIEW
a
a
a b
c d
bb
b
b
b
a
a
b
b
b
b
a
b
b
a
R42868-BCRYSTR
b
b
R42868-ACRYSTR
R42868-AROPE
bottom strands
R42868-BROPE
b
a
a
b
b
b
b
a
b
b
a
top strands
01.01.13
Page 3
FRIS19
HANGING INSTRUCTIONS
SAFETY WARNING: Read wiring and grounding instructions [FRIS 18]
and any additional directions. Turn power supply off during installation. If new wiring
is required, consult a qualified electrician or local authorities for code requirements.
STEP 1
1 Shut off electrical current before starting. If the fixture you are replacing is
turned on and off by a wall switch, simply turn the switch off. If not, remove the
appropriate fuse (or open the circut breakers) until the fixture is dead.
• DO NOT restore current - either by fuse, breaker or switch - until the new
fixture is completely wired and in place.
STEP 2
1 Fasten mounting strap (1) to outlet box (a) with the original outlet box screws (2)
- See Drawing 1.
2 Thread nipple (3) into mounting strap (1).
3 Thread loop (4) on to end of nipple (3).
4 Slip canopy (b) over loop (4) and adjust height of loop so half of thread area is
exposed.
STEP 3
1 Taking the chain, determine the length you require to hang the fixture.
2 Attach one end of the chain to the top loop of the fixture - See Drawing 2.
3 Now slip loop collar (5) and canopy (b) onto chain.
4 Attach other end of chain to loop (4). Get assistance for this step since fixture
may be heavy and difficult to hold while attaching the chain.
a
1
2
3
b
4
ground
wire
[DRAWING 1]
6
5
supply wire
chain
STEP 4
1 Unwrap supply wire and ground wire and weave them up through the chain.
2 Slip supply wire and ground wire through center of loop (4).
3 Connect ground wire to mounting strap (1) using green ground screw (6).
4 Make electrical connections from supply wire to fixture lead wires. Refer to
instruction sheet [FRIS18] and follow all instructions to make all necessary
wiring connections.
5 Slip canopy up firmly against the ceiling and secure by turning the threaded
collar (5) on loop (4) until tight.
[DRAWING 2]
Half of thread area of loop (4) is to be exposed.
This will allow collar (5) to be threaded on later.
b
4
chain
Page 4
FRIS18
WIRING AND GROUNDING INSTRUCTIONS
SAFETY WARNING: Read wiring and grounding instructions
[FRIS 18] and any additional directions. Turn power supply off during installation. If new
wiring is required, consult a qualified electrician or local authorities for code requirements.
STEP 1 WIRING INSTRUCTIONS
Indoor Fixtures
1 Connect positive supply wire (a) (typically black or the smooth, unmarked side of
the two-conductor cord) to positive fixture lead (b) with appropriately sized twist
on connector - See Drawings 1 or 2.
2 Connect negative supply wire (c) (typically white or the ribbed, marked side of
the two-conductor cord) to negative fixture lead (d).
3 Please refer to the grounding instructions below to complete all electrical
connections.
Outdoor Fixtures
1 Connect positive supply wire (a) (typically black or the smooth unmarked side of
the two-conductor cord) to positive fixture lead (b) with appropriately sized twist
on connector - See Drawings 2 or 3.
2 Connect negative supply wire (c) (typically white or the ribbed, marked side of
the two-conductor cord) to negative fixture lead (d).
3 Cover open end of connectors with silicone sealant to form a watertight seal.
• If installing a wall mount fixture, use caulk to seal gaps between the fixture
mounting plate (backplate) and the wall. This will help prevent water from
entering the outlet box. If the wall surface is lap siding, use caulk and a fixture
mounting platform specially.
4 Please refer to the grounding instructions below to complete all electrical
connections.
STEP 2 GROUNDING INSTRUCTIONS
Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground
wire (e) (typically copper or green plastic coated) to the fixture mounting strap
(1) with the ground screw (2) - See Drawing 1.
Note: On straps for screw supported fixtures, first install the two mounting
screws in strap.
Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop fixture ground wire (e) (typically copper or green plastic coated) under the
head of the ground screw (2) on fixture mounting strap (1) and connect to the
loose end of the fixture ground wire directly to the ground wire of the building
system with appropriately sized twist-on connectors - See Drawing 2.
Post-Mount Fixtures
Connect fixture ground wire (e) (typically copper or green plastic coated) to
power supply ground with appropriately sized twist-on connector inside post.
Cover open end of connector with silicone sealant to form a watertight seal - See
Drawing 3.
supply wire
a c e
b
xture leads
supply wire
a c
b d
xture leads
supply wire
a c
d
b
xture leads
[drawing 1]
twist-on
d
connectors
[drawing 2]
twist-on
e
connectors
1
2
e
[drawing 3]
e
twist-on
connectors
e
1
2
1.30.08
Loading...