
HAMLET
FR42861
Bulbs: 60W canD. Replacement Parts: crystals: R 42861CRYS TR ROPE: R42861ROPE
A S S EMBLY INSTRU C T ION S
Assembly of this fixture will be accomplished by first attaching the mounting hardware
to the junctin box, making all necessary electrical connections, mounting the fixture to
the ceiling and then attaching the rope and crystal accents.
SAFE TY WARNING: Read wiring and grounding instructions [FRIS 18]
and any additional directions. Turn power supply off during installation. If new wiring
is required, consult a qualified electrician or local authorities for code requirements.
STEP 1
1 Prepare mounting strap (a) by threading the two long mounting screws (b)
into the back of the mounting strap (a), making sure the holes into which the
screws are threaded match the spacing of holes (d) in the canopy (e) - See
Drawing 1.
2 Attach mounting strap (a) to junction box (j) using two screws (c).
3 Make electrical connections from supply wire to fixture lead wires. Refer to
instruction sheet [FRIS18] and follow all instructions to make all necessary
wiring connections. Then refer back to this sheet to continue installation of
this fixture.
4 To mount fixture, slip the two mounting screws (b) through the two mounting
holes (d) in the canopy (e).
5 While holding fixture in place, thread the two ball knobs (f) on to the end of the
mounting screws (b), and tighten.
STEP 2
1 Prior to installing rope and crystal accents, fixture can now be lamped accord-
ingly.
2 Thread center tube (2) into coupler (1) approximately 3/8” - see Drawing 2.
3 Slip tube (3) over center stem (2) and hold in position.
4 Slip small tube cap (4) onto center tube (2) followed by large cap, with side
holes, (5).
5 Thread knurled nut (6) onto end of center tube (2) and tighten to secure parts.
7 Thread finial (7) onto end of center tube (2) and tighten.
8 Refer to Accent installation instructions to complete fixture.
[DRAWING 1]
[DRAWING 2]
2
4
6
j
b
a
c
e
d
f
1
3
5
7
06.01.13

HAMLET
FR42861
CRYSTAL AND ROPE ACCENT INSTALLATION INSTRUCTIONS.
S T EP 1
1 Unpack all the crystal (8) and rope strands (9), fixture should be lamped
accordingly, prior to crystal and rope strand installation.
2 Start by attaching a crystal strand (8) [large crystal end to large ring ]
Attach other end of crystal strand to the corresponding hole
in the small bottom ring (5). Making sure
strand hangs perpenducular to large ring ring.
3 Using top view guide below continue adding crystal strands (8) and
rope strands (9)around the fixture until completed.
NOTE: use reference drawings below.
[DRAWING 1]
9
8
TOP VIEW
9
9
8
9
9
crystal and rope reference guide
9
9
9
8
9
9
8
9
8
8
9
9
8
9
8
9
8
9
9
8
9
9
9
8
R42861CRYSTR
9
8
R42861ROPE
9
01.01.13

Drawing 1 - Flush Mount
supply wire
A CC
E
I.S. 18 wiring grounding instructions
I.S. 18
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)
AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING
INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED
ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
wiring instructions
Indoor Fixtures
B
fixture leads
Drawing 2 - Chain Hung
supply wire
connectors
twist-on
D
A C
twist-on
E
E
connectors
1
E
E
D
B
fixture leads
Drawing 3 - Post-Mount
supply wire
A C
2
E
twist-on
connectors
E
D
B
fixture leads
1
2
1. Connect positive supply wire (A) (typically black or the smooth, unmarked
side of the two-conductor cord) to positive fixture lead (B) with appropriately
sized twist on connector - see Drawings 1 or 2.
2. Connect negative supply wire (C) (typically white or the ribbed, marked
side of the two-conductor cord) to negative fixture lead (D).
3. Please refer to the grounding instructions below to complete all
electrical connections.
Outdoor Fixtures
1. Connect positive supply wire (A) (typically black or the smooth unmarked
side of the two-conductor cord) to positive fixture lead (B) with appropriately
sized twist on connector - see Drawings 2 or 3.
2. Connect negative supply wire (C) (typically white or the ribbed, marked
side of the two-conductor cord) to negative fixture lead (D).
3. Cover open end of connectors with silicone sealant to form a watertight seal.
• If installing a wall mount fixture, use caulk to seal gaps between the fixture
mounting plate (backplate) and the wall. This will help prevent water from
entering the outlet box. If the wall surface is lap siding, use caulk and a
fixture mounting platform specially.
4. Please refer to the grounding instructions below to complete all
electrical connections.
grounding instructions
Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground
wire (E) (typically copper or green plastic coated) to the fixture mounting strap (1)
with the ground screw (2) - see Drawing 1.
Note: On straps for screw supported fixtures, first install the two mounting screws in strap.
Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop fixture ground wire (E) (typically copper or green plastic coated) under the
head of the ground screw (2) on fixture mounting strap (1) and connect to the
loose end of the fixture ground wire directly to the ground wire of the building
system with appropriately sized twist-on connectors - see Drawing 2.
Post-Mount Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated) to power
supply ground with appropriately sized twist-on connector inside post. Cover open
end of connector with silicone sealant to form a watertight seal - see Drawing 3.
HINKLEY LIGHTING 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com