Page 1
Bulbs : 10 0W MED.
SPECTRA
fR 37554
A SSEMBLY INSTRU C T IONS
Assembly of this fixture will be accomplished by first determining the length of stem
required, attaching the mounting strap to the junction box, making all necessary
electrical connections, and hanging the fixture from the ceiling.
SAFETY WARNING: Read wiring and grounding instructions [FRIS 18]
and any additional directions. Turn power supply off during installation. If new wiring
is required, consult a qualified electrician or local authorities for code requirements.
ST E P 1
1 Determine the overall length you will need the assembled fixture to be.
2 Determine what stems will be needed to achieve the overall length you
require.(Additional stems are available and can be ordered. Ask your local
Fredrick Ramond representative or visit www.fredrickramond.com for
information.
3 Install first stem (a) by slipping it along the supply wire of the fixture, and
threading it into decorative coupler (b) of cage assembly (c) - see Drawing 1.
4
Continue adding stems (a) until determined length is acheived.
5
Fixture is ready for installation. Follow instruction sheet [FRIS19-91] provided.
[DRAWI NG 1]
supply
wire
a
b
c
5
6
6a
After installation fixture can be lamped accordingly and glass installed.
6
7
To install glass, thread one of the decorative knobs (3) onto one end of center
tube (4) and slip plastic washer (3a) onto center tube (4).
8
Slip bottom piece of glass (5) into bottom of cage (c), slip center tube (4) through
center hole of bottom glass (5), lift glass into center ring (r), making sure glass seats
inside ring, and hold parts in postion. Note: both pieces of glass are the same.
9
Slip top glass (5) into top of cage assembly (c), and slip center hole of glass onto
center tube (4) and down onto center ring (r) making sure seats inside ring.
10
Slip second plastic washer (6a) onto center tube (4) and thread decorative knob
(6) onto end of center tube to secure glass pieces (5).
Fixture is complete and power can be restored.
11
r
5
3
4
3a
01.01.13
Page 2
FRIS18
WIRING AND GROUNDING INSTRUCTIONS
SAFETY WARNING: Read wiring and grounding instructions
[FRIS 18] and any additional directions. Turn power supply off during installation. If new
wiring is required, consult a qualified electrician or local authorities for code requirements.
STEP 1 WIRING INSTRUCTIONS
Indoor Fixtures
1 Connect positive supply wire (a) (typically black or the smooth, unmarked side of
the two-conductor cord) to positive fixture lead (b) with appropriately sized twist
on connector - See Drawings 1 or 2.
2 Connect negative supply wire (c) (typically white or the ribbed, marked side of
the two-conductor cord) to negative fixture lead (d).
3 Please refer to the grounding instructions below to complete all electrical
connections.
Outdoor Fixtures
1 Connect positive supply wire (a) (typically black or the smooth unmarked side of
the two-conductor cord) to positive fixture lead (b) with appropriately sized twist
on connector - See Drawings 2 or 3.
2 Connect negative supply wire (c) (typically white or the ribbed, marked side of
the two-conductor cord) to negative fixture lead (d).
3 Cover open end of connectors with silicone sealant to form a watertight seal.
• If installing a wall mount fixture, use caulk to seal gaps between the fixture
mounting plate (backplate) and the wall. This will help prevent water from
entering the outlet box. If the wall surface is lap siding, use caulk and a fixture
mounting platform specially.
4 Please refer to the grounding instructions below to complete all electrical
connections.
STEP 2 GROUNDING INSTRUCTIONS
Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground
wire (e) (typically copper or green plastic coated) to the fixture mounting strap
(1) with the ground screw (2) - See Drawing 1.
Note: On straps for screw supported fixtures, first install the two mounting
screws in strap.
Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop fixture ground wire (e) (typically copper or green plastic coated) under the
head of the ground screw (2) on fixture mounting strap (1) and connect to the
loose end of the fixture ground wire directly to the ground wire of the building
system with appropriately sized twist-on connectors - See Drawing 2.
Post-Mount Fixtures
Connect fixture ground wire (e) (typically copper or green plastic coated) to
power supply ground with appropriately sized twist-on connector inside post.
Cover open end of connector with silicone sealant to form a watertight seal - See
Drawing 3.
supply wire
a c e
b
xture leads
supply wire
a c
b d
xture leads
supply wire
a c
d
b
xture leads
[drawing 1]
twist-on
d
connectors
[drawing 2]
twist-on
e
connectors
1
2
e
[drawing 3]
e
twist-on
connectors
e
1
2
1.30.08
Page 3
FRIS19-91
SAFE TY WARNING: Read wiring and grounding instructions [FRIS 18]
and any additional directions. Turn power supply off during installation. If new wiring
is required, consult a qualified electrician or local authorities for code requirements.
STEP 1
1
Shut off electrical current before starting. If the fixture you are replacing is
turned on and off by a wall switch, simply turn the switch off. If not, remove
the appropriate fuse (or open the circut breakers) until the fixture is dead.
• DO NOT restore current - either by fuse, breaker or switch - until the new
fixture is completely wired and in place.
STEP 2
Drawing 1 - Mounting instructions
Slip canopy assembly with swivel (3) along wire and thread onto top of rods
that are attached to fixture.
STEP 3
Thread two long 8-32 (1) screws provided into the mounting strap (2).
Note: the two screws should be threaded into holes that line up with the holes
in the canopy
Attach mount strap (2) to junction box with two short 8-32 screws (5) .
Make wire connections following the instructions on (I.S.18) instruction sheet
provided.
Slip canopy/fixture over screws (1) and secure fixture with ball knobs (4).
(3) - see Drawing 1.
2
5
1
2223
4
supply wire
800. 421.35 17 WWW .F RE DRICKRAMO ND .CO M
01.01.12
Loading...