Hinkley Lighting 59009 User Manual

installation instructions

Family: 120V Series Brick Light Item No. 59040/59009 BZ

HINKLEY LIGHTING

59040

59009

Drawing 1 - Lamp Installation

ED

B

C

WARNING: TO REDUCE THE
RISK OF FIRE, OR INJURY
TO PERSONS:

1. Turn off/unplug and allow
to cool before replacing lamp.

2. Lamps get hot quickly!
Contact only switch/plug
when turning on.

3. Do not touch hot lens,
guard or enclosure.

4. Keep lamp away from
material that may burn.

5. Do not operate luminaire
fitting with a missing
or damaged cover.

start here

1. Find a clear area in which you can work.

2. Carefully review instructions prior to assembly.

3. Gather tools required : WIRE STRIPPERS, PHILIPS HEAD SCREWDRIVER,

SILICONE GREASE, THREAD SEALANT.

• Save these instructions for future reference.

WARNING: LUMINAIRE MUST BE INSTALLED AND GROUNDED IN ACCORDANCE
WITH THE NATIONAL ELECTRICAL CODE (NEC) AND LOCAL CODES. FAILURE TO
DO SO MAY RESULT IN SERIOUS INJURY AND/ OR DAMAGE TO THE LUMINAIRE.

FIXTURES WHICH MAY COME IN CONTACT WITH OR BE EXPOSED TO MOISTURE
(I.E. OUTDOORS) SHALL BE INSTALLED ON A GFI (GROUND FAULT INTERRUPTOR)
POTECTED CIRCUIT.

ALWAYS USE UL RECOGNIZED WIRE CONNECTORS FOR CONNECTIONS.

1. Please refer to the mounting instructions located on the back of this sheet to
continue installation of this fixture.

lamp installation replacement

1. To prevent electrical shock, disconnect from the electrical supply before servicing.

2. Remove face plate (B) by loosening 4 philips screws (C) on front of louvre - see

Drawing 1.

3. Remove electrical tray (D) by loosening 2 philips screws (E).

4. Replace lamp with correct wattage and type marked on fixture label.

CAUTION: DO NOT EXCEED MAXIMUM WATTAGE MARKED ON LUMINAIRE LABEL.

Info 59040 BZ: Lamp Type G9, Maximum Wattage is 40 watts per bulb.
Info 49009 BZ: Lamp Type G23-2, Maximum Wattage is 9 watts CFL per bulb.

H I N K L E Y L I G H T I N G 1 2 600 B ere a Roa d Cle vela nd, OH 4 4111 8 00.4 46.5 539 / 21 6.67 1.33 00 w ww. h inkl e y lig htin g.co m

Drawing 2 - Fixture Mounting

mounting instructions

Family: 120V Series Brick Light Item No. 59040/59009 BZ

HG

54F

Drawing 3 - Fixture Mounting

THERMAL PROTECTION IS NOT REQUIRED FOR MASONARY OR CONCRETE
POUR INSTALLATIONS. THERMAL PROTECTION IS ALSO NOT REQUIREED FOR
FLUORESCENT LAMPING SINCE RECESSED BRICKLIGHT BALLAST IS CLASS P
AND CONTAINS THERMAL PROTECTION.

1

2

1

2

1. Determine which of the two mounting options are required and refer to the proper

set of instructions below.

Masonary Wall Installation

1. Install fixture housing (H) into the masonary open hole dedicated for the brick light -
see Drawing 2.

2. Drill two 1/8” pilot holes (4) into each side of the bricks (5) using the two 3/16” holes
(F) in housing (H).

3. Remove the 1/2”NPT plugs (G) from the side and bottom of the housing and pull
supply wires through holes and into housing (H).

4. Leaving 1/8” of housing extended past front of wall, press fixture firmly against the
bricks and thread two 8-32 x 1 3/4” countersunk flat head philips lag screws (5) (not
provided) into the 1/8” pilot holes (4).

5. Please refer back to the front of this sheet to install the lamp and complete
installation of this fixture.

J

3

Concrete Pour Installation

L K

1. Level supplied template (F) (refer to second page for template) on wood support

frame (1) (not provided) and drill two 3/16” diameter clearence holes (2). Failure to
level will cause fixture to have tilted appearence - see Drawing 3.

2. Remove the 1/2” NPT plugs (L) from the side and bottom of the housing (K) and pull
the supply wires through the holes and into the housing (K).

3. Be sure all unused electrical plugs have been replaced. Using template (F), cut 1/8”
deep outline into back of wood support (1).

4. Secure housing to wood support (1), with two 8-32 X 1 3/4” wood screws (3) not
provided. Housing (K) must extend 1/8” past front of finished walls.

5. Pour concrete.

6. After concrete is dry, remove two screws (3) and wood support.

7. Please refer back to the front of this sheet to install the lamp and complete

installation of this fixture.