Hinkley Lighting 58009 User Manual

installation instructions

Family: 120V Series Step Light Item No. 58025/58009 BZ

HINKLEY LIGHTING

58025

58009

Drawing 1 - Lamp Installation

B

A

WARNING: TO REDUCE THE
RISK OF FIRE, OR INJURY
TO PERSONS:

1. Turn off/unplug and allow
to cool before replacing lamp.

2. Lamps get hot quickly!
Contact only switch/plug
when turning on.

3. Do not touch hot lens,
guard or enclosure.

4. Keep lamp away from
material that may burn.

5. Do not operate luminaire
fitting with a missing
or damaged cover.

C

start here

1. Find a clear area in which you can work.

2. Carefully review instructions prior to assembly.

3. Gather tools required : WIRE STRIPPERS, PHILIPS HEAD SCREWDRIVER,

SILICONE GREASE, THREAD SEALANT.

• Save these instructions for future reference.

WARNING: LUMINAIRE MUST BE INSTALLED AND GROUNDED IN ACCORDANCE
WITH THE NATIONAL ELECTRICAL CODE (NEC) AND LOCAL CODES. FAILURE TO
DO SO MAY RESULT IN SERIOUS INJURY AND/ OR DAMAGE TO THE LUMINAIRE.
FOR ANY SPECIAL APPLICATIONS NOT COVERED, PLEASE CONTACT HINKLEY
LIGHTING FOR ASSISTANCE

FIXTURES WHICH MAY COME IN CONTACT WITH OR BE EXPOSED TO MOISTURE
(I.E. OUTDOORS) SHALL BE INSTALLED ON A GFI (GROUND FAULT INTERRUPTOR)
POTECTED CIRCUIT.

ALWAYS USE UL RECOGNIZED WIRE CONNECTORS FOR CONNECTIONS.

1. Please refer to the mounting instructions located on the back of this sheet to
continue installation of this fixture.

lamp installation replacement

1. To prevent electrical shock, disconnect from the electrical supply before servicing.

2. Remove face plate (A) from housing (B) by loosening 2 philips screws on front of

louver (C) - see Drawing 1.

3. Replace lamp with correct wattage and type marked on fixture label.

CAUTION: DO NOT EXCEED MAXIMUM WATTAGE MARKED ON LUMINAIRE LABEL.

Info 58025 BZ: Lamp Type G9, Maximum Wattage is 25 watts per bulb.
Info 58009 BZ: Lamp Type G23-2, Maximum Wattage is 9 watts CFL per bulb.

H I N K L E Y L I G H T I N G 1 2 600 B ere a Roa d Cle vela nd, OH 4 4111 8 00.4 46.5 539 / 21 6.67 1.33 00 w ww. h inkl e y lig htin g.co m

Drawing 2 - Fixture Mounting

STEPLIGHT

D

B

2

1

mounting instructions

Family: 120V Series Step Light Item No. 58025/58009 BZ

THERMAL PROTECTION IS NOT REQUIREED FOR THIS FLUORESCENT LAMPING.

1

1. Level Supplied template (D) - see Drawing 3 - on desired step area (1) and drill four

diameter clearence holes (2) - see Drawing 2. Failure to level will cause fixture to have
a tilted appearance.

2. Remove the 1/2” PT plugs (E) from the side and bottom of the housing (B) and pull
the supply wires through the holes and into the housing (B).

3. Be sure all unused electrical plugs have been relaced. Using template (D), cut
placement hole into desired step area (1).

4. Secure housing to desired step area (1) with four 8-32 x 1 3/4” wood screws (3) not
provided to housing (B).

5. Please refer back to the front of this sheet to install lamp and complete the
installation of this fixture.

Drawing 3 - Template

3

Through

Ø

1

"

6

Holes

1

6

4

THIS SIDE UP

[Ø4.76mm

(4)

" [159.23mm]

]

Required

.