Hinkley Lighting 4244OB User Manual

Download

Page 1

Drawing 1 - Fixture Assembly

H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com

wire

assembly instructions

4244

Family: Plymouth Item No. 4244 OB

start here

1. Find a clear area in which you can work.

2. Unpack ﬁxture and glass from carton.

3. Carefully review instructions prior to assembly.

*** The construction of this ﬁxture will be accomplished by ﬁrst assembling the main body of the ﬁxture, hanging the ﬁxture from the ceiling, and then installing the glass.

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED

ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

1. Slip top cap (1) with loop attached, along wire and thread onto top of wiring compartment (2) - see Drawing 1.

2. Fold out arms (3) until they are equally spaced 120 degrees apart.

3. Using the 4 ball knobs and stud screws (4) provided, attach the 2 white perforated bulb shields (5) to the shield bracket (E).

4. Thread stem (6) into coupler (A), located in the center of the socket cluster (B), approximately 1/4”.

5. Using a 9/16” wrench, tighten hex nut (C) against coupler (A) to lock stem (6) in place.

6. Adjust hex nut (D) on stem (6) until it is approximately 2 3/4” from the bottom

of the stem.

7. Please refer to the hanging instruction sheet (I.S. 19) provided to continue installation of this ﬁxture. Refer back to this sheet for glass installation instructions below.

1. Slip steel ﬂat washer (7) onto stem (6) - see Drawing 1.

2. Slip rubber washer (8) onto stem (6).

3. Slip glass (9) onto stem (6) and hold in position.

4. Hold glass (9) in position and slip rubber washer (10) onto stem (6) followed by ﬂat washer (11). Hold pieces in place.

5. Thread hex nut (12) onto stem (6) and cautiously tighten up against glass (9). Over tightening of parts could cause glass damage.

6. Slip bottom cap (13) followed by ball knob (14) onto center stem (6) and hold in place

6. Thread ﬁnial (15) onto end of center stem (6) and tighten to secure parts.

2.7.08

Page 2

I.S.19 hanging instructions

I.S. 19

Drawing 1 - Hanging Assembly

weave supply wire and

ground wire through chain

start here

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED

ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

1. Shut off electrical current before starting. If the ﬁxture you are replacing is turned on and off by a wall switch, simply turn the switch off. If not, remove the appropriate fuse (or open the circut breakers) until the ﬁxture is dead.

• DO NOT restore current - either by fuse, breaker or switch - until the new ﬁxture is completely wired and in place.

1. fasten mounting strap (1) to outlet box (A) with the two 8-32 screws (2) -see Drawing 1.

2. Thread 2 - hex nuts (3a) and (3b) onto threaded tubing (4).

3. Thread one end of threaded tubing (4) into loop (5) a minimum of 1/2” to 3/4”. Thighten hexnut (3a) against loop (5) to lock loop in position.

4. Thread other end of threaded tube (4) into mounting strap (1) approximately 1/2”.

5. Slip canopy (B) over loop (5) and adjust height of loop so half of the threaded area on the loop is exposed - see Drawing 2 below. After loop height is adjusted, thigten hex nut (3b) up against mounting strap, tighten against mounting strap to lock loop and threaded tube in position.

6. Remove mounting strap (1) from junction box (A), and thread third hex nut (3c) onto end of threaded tube (4) above the mounting strap, tighten against mounting strap to lock assembly in position.

7. Remount mounting strap to junction box.

1. Taking the chain, determine the length you require to hang the ﬁxture.

2. Attach one end of the chain to the top loop of the ﬁxture - see Drawing 2.

3. Now slip loop collar (5) and canopy (B) onto chain.

4. Attach other end of chain to loop (4). Get assistance for this step since ﬁxture

may be heavy and difﬁcult to hold while attaching the chain.

Drawing 2 - Canopy Adjustment

half of threaded area exposed

HINKLEY LIGHTING 33000Pin Oak Parkway, Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com

1. Unwrap supply wire and ground wire and weave them up through the chain.

2. Slip supply wire and ground wire through center of loop (4).

3. Connect ground wire to mounting strap (1) using green ground screw (6).

4. Make electrical connections from supply wire to ﬁxture lead wires. Refer to

instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections.

5. Slip canopy up ﬁrmly against the ceiling and secure by turning the threaded collar (5) on loop (4) until tight.

Page 3

Drawing 1 - Flush Mount

H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com

supply wire

A CC

I.S. 18 wiring grounding instructions

I.S. 18

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

wiring instructions

Indoor Fixtures

ﬁxture leads

Drawing 2 - Chain Hung

supply wire

connectors

twist-on

A C

twist-on

connectors

ﬁxture leads

Drawing 3 - Post-Mount

supply wire

A C

twist-on connectors

ﬁxture leads

1. Connect positive supply wire (A) (typically black or the smooth, unmarked

side of the two-conductor cord) to positive ﬁxture lead (B) with appropriately sized twist on connector - see Drawings 1 or 2.

2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative ﬁxture lead (D).

3. Please refer to the grounding instructions below to complete all electrical connections.

Outdoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive ﬁxture lead (B) with appropriately sized twist on connector - see Drawings 2 or 3.

2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative ﬁxture lead (D).

3. Cover open end of connectors with silicone sealant to form a watertight seal.

• If installing a wall mount ﬁxture, use caulk to seal gaps between the ﬁxture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a ﬁxture mounting platform specially.

4. Please refer to the grounding instructions below to complete all electrical connections.

grounding instructions

Flush Mount Fixtures

For positive grounding in a 3-wire electrical system, fasten the ﬁxture ground wire (E) (typically copper or green plastic coated) to the ﬁxture mounting strap (1) with the ground screw (2) - see Drawing 1.

Note: On straps for screw supported ﬁxtures, ﬁrst install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.

Chain Hung Fixtures

Loop ﬁxture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (2) on ﬁxture mounting strap (1) and connect to the loose end of the ﬁxture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors - see Drawing 2.

Post-Mount Fixtures

Connect ﬁxture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal - see Drawing 3.