Hinkley Lighting 3664BN User Manual

Drawing 1 - Fixture Assembly

assembly instructions

3664

Item No. 3664

1. Find a clear area in which you can work.

2. Unpack xture and glass from carton.

3. Carefully review instructions prior to assembly.

*** The construction of this xture will be accomplished by rst assembling the main body,
hanging the xture, and then installing the xture glass.

1

2

3

5

6

8

4

7

2

12

3

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)

AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING

INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED

ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

1. The main body assembly and be mounted to the ceiling prior to attaching the glass.
Please follow instruction sheet (IS19-91) provided.

2. After fixture is installed please return to this section for instructions on how to install
the glass.

1. To install glass, slip center hole of glass (4) onto locator disc (3), located at the

base of the adjustable center stem (2), of the cental assembly (1). Hold glass in

position - see Drawing 3.

2. While holding glass (4) slip cap (5) onto center stem (2) and hold in postion.

3. Thread on hexnut (6) onto center stem (2) and thighten to secure glass to fixture.

4. Slip decorative cap (7) onto center stem.

5. thread knob (8) onto end of center stem (2) and tighten to complete assembly.

6.1.12

HINKLEY LIGHTING 33000 Pin Oak Parkway Avon Lake, Ohio 44012 800-446-5539 www.hinkleylighting.com

Drawing 1 - Flush Mount

H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com

supply wire

A CC

E

I.S. 18 wiring grounding instructions

I.S. 18

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)
AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING
INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED
ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

wiring instructions

Indoor Fixtures

B

fixture leads

Drawing 2 - Chain Hung

supply wire

connectors

twist-on

D

A C

twist-on

E

E

connectors

1

E

E

D

B

fixture leads

Drawing 3 - Post-Mount

supply wire

A C

2

E

twist-on
connectors

E

D

B

fixture leads

1

2

1. Connect positive supply wire (A) (typically black or the smooth, unmarked

side of the two-conductor cord) to positive fixture lead (B) with appropriately
sized twist on connector - see Drawings 1 or 2.

2. Connect negative supply wire (C) (typically white or the ribbed, marked
side of the two-conductor cord) to negative fixture lead (D).

3. Please refer to the grounding instructions below to complete all
electrical connections.

Outdoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth unmarked
side of the two-conductor cord) to positive fixture lead (B) with appropriately
sized twist on connector - see Drawings 2 or 3.

2. Connect negative supply wire (C) (typically white or the ribbed, marked
side of the two-conductor cord) to negative fixture lead (D).

3. Cover open end of connectors with silicone sealant to form a watertight seal.

• If installing a wall mount fixture, use caulk to seal gaps between the fixture
mounting plate (backplate) and the wall. This will help prevent water from
entering the outlet box. If the wall surface is lap siding, use caulk and a
fixture mounting platform specially.

4. Please refer to the grounding instructions below to complete all
electrical connections.

grounding instructions

Flush Mount Fixtures

For positive grounding in a 3-wire electrical system, fasten the fixture ground
wire (E) (typically copper or green plastic coated) to the fixture mounting strap (1)
with the ground screw (2) - see Drawing 1.

Note: On straps for screw supported fixtures, first install the two mounting screws in strap.
Any remaining tapped hole may be used for the ground screw.

Chain Hung Fixtures

Loop fixture ground wire (E) (typically copper or green plastic coated) under the
head of the ground screw (2) on fixture mounting strap (1) and connect to the
loose end of the fixture ground wire directly to the ground wire of the building
system with appropriately sized twist-on connectors - see Drawing 2.

Post-Mount Fixtures

Connect fixture ground wire (E) (typically copper or green plastic coated) to power
supply ground with appropriately sized twist-on connector inside post. Cover open
end of connector with silicone sealant to form a watertight seal - see Drawing 3.