Hinari LifeStyle compact DW002 User Manual

Read all the safety instructions before first use of your Dishwasher DW002.

Safety instructions

!

2

Electrical information

Make sure that the voltage of your electricity
supply is the same as that indicated on the
rating plate. This appliance may be fitted with
a non-rewireable plug. If you need to change
the fuse in a non-rewireable plug, the fuse
cover must be refitted. If the fuse cover is lost
or damaged, the plug must not be used until a
replacement is obtained (available from the
appliance manufacturer). It is important that
the colour of the replacement fuse cover
corresponds with the colour marking on the
base of the plug.
If the plug has to be changed because it is not
suitable for your socket, or becomes damaged,
it should be cut off and an appropriate plug
fitted following the wiring instructions below.
The plug removed must be disposed of safely
as insertion into a mains socket is likely to
cause an electrical hazard.
If a 13 Amp (BS1363) plug is used, a 13 Amp
fuse (BS1362) must be fitted, or if any other
type of plug is used a 13 Amp fuse must be
fitted, either in the plug, adaptor or on the
distribution board.

Important: This appliance must be
earthed

As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals
in your plug, proceed as follows:-

• The blue wire must be connected to the
terminal marked with the letter N or
coloured black.

• The brown wire must be connected to the
terminal marked with the letter L or
coloured red.

• The green/yellow
wire must be
connected to the
terminal marked
with the letter E
or coloured
green.

Power source

You should only plug your dishwasher into a
230V to 240VAC, 50Hz 10A supply.

Using your dishwasher

• The dishwasher is for household use only

and must not be used outside.

• Do not immerse the electrical cable or
plug in water.

• Do not install the dishwasher in an
unventilated cupboard.

• Close supervision is required when used
near children.

• Do not use attachments or accessories not
recommended by the manufacturer.

• Do not use the dishwasher with a damaged
cable or plug or after the appliance has
malfunctioned or has been damaged.
Return it to the nearest authorised service
centre for repair.

Servicing

• There are no user serviceable parts in your
dishwasher.

• Consult your dealer if you are ever in
doubt about the installation, operation or
safety of your dishwasher.

CAUTION

RISK OF ELECTRIC SHOCK

3

Getting started

Remove your Hinari DW002
carefully from the box. You may
wish to store the packaging for
future use.

Thank you for purchasing the Hinari DW002
dishwasher.

Please Note

This dishwasher has been factory tested using
water. Whilst every effort has been made to
remove all the water, some traces may still
remain. This will have no detrimental effect
on your dishwasher.

In the box

Inside your dishwasher package you should
have:

• Dishwasher

• Dish rack

• Cutlery basket

• Detergent measure (inside the cutlery
basket)

• Rubber seal (inside the cutlery basket)

• User guide

Should any of these items be missing please
call the helpline on 020 8787 3111.

Read these instructions before use.

Dishwasher installation

The dishwasher can be installed on a flat
surface either:-

• On a work surface next to the sink ‘A’

• Built into a cabinet without a door ‘B’

• Built into a ventilated cabinet with
a door ‘C’

Important

Do not install the dishwasher in a cabinet
without ventilation as the door must remain
open at the end of the wash cycle and the
released steam could damage the cabinet.

To ensure the stability of the dishwasher
secure it to the wall or rear of the cabinet
with a 6mm screw (not supplied) through the
bracket attached to the back of the
dishwasher.

Please Note

Do not turn the dishwasher on its side or
upside down at any time during
transportation or installation.

Water supply

Your dishwasher is supplied with a 9mm bore
fill hose fitted with a ¾ inch BSP female
connector for connection to a cold/hot water
supply. The water pressure must be between

0.5 and 10 bar (50 and 1000 kPa).
If the dishwasher is connected to a hot water
supply the water temperature must not exceed
65°C.

Please Note

As the wash cycle requires the water to be at
65°C, the cycle time will be reduced if
connected to a hot water supply. However,

4

the cold water rinse temperature will no
longer be cold but at the hot water
temperature.

WARNING

INSTANTANEOUS GAS AND
ELECTRIC WATER HEATERS MUST
NOT BE USED.

Plumbing

The water supply can be either a permanently
plumbed supply, in which case a tap must be
incorporated which can completely shut off
the water supply, or from your sink tap.

Permanent

Please Note

Permanent plumbing must be carried out by
an experienced plumber and must comply
with the regulations of your water supplier.

Put the rubber seal into the ¾ inch BSP
female connector and screw the connector to
the permanent water supply outlet. Do not
shorten the fill hose. If it is too long coil it up
behind the dishwasher.

Mobile

It is essential, if you are operating from a sink
tap, that the tap is in good condition. If not,
you may have leakage problems when the tap
is turned full on.

To operate from a sink tap you will need a tap
adapter with a ¾ inch BSP connection (not
supplied). These are readily available from
DIY suppliers.

Put the rubber seal into the ¾ inch BSP
female connector and screw the connector to
the tap adapter. Do not shorten the fill hose.
If it is too long coil it up behind the
dishwasher.

Please Note

Mixer taps are not suitable for use with your
dishwasher. In this case the dishwasher will
have to be permanently plumbed in.

Drainage requirements

Drainage can be:

• Into a standpipe ‘A’

• To your sink waste pipe ‘B’

• Into your sink ‘C’

Standpipe - A

To allow an airbreak between the discharge
hose and the standpipe, the standpipe must
have a diameter of at least 38mm. The height
of the standpipe is dependent on the position
of the dishwasher. No part of the discharge
hose can be higher than the top of the
dishwasher. The discharge hose can be
shortened if required. Make sure the hooked
end support is positioned near the end of the
hose.

The standpipe should have a trap fitted and
must be connected to the foul or combined
drain from your house but NOT a surface
water drain. If in doubt ask your plumber or
local authority.

Sink waste pipe - B

You can connect the discharge hose to your
sink waste pipe with an adapter (not
supplied). The adaptor fits into the waste
pipe and the discharge hose is connected to a
T-piece on the adapter. Remove the hooked

5

end support and cut the discharge pipe to the
required length.

Sink - C

The discharge hose should be fixed over the
edge of the sink. The dishwasher must be
positioned so that the top of the dishwasher is
higher than the discharge hose.
The sink must have an outlet pipe of a
minimum of 32mm to prevent overfilling the
sink.

Always remove the sink plug when using the
dishwasher.

WARNING

IF YOU ARE USING THE SINK FOR
OTHER PURPOSES AT THE SAME
TIME BE CAREFUL, THE DISCHARGE
WATER FROM THE MACHINE MAY
BE VERY HOT.