HIKVISION iVMS-5200 User Manual
iVMS-5200 Control Client
User Manual
UD.6L0202D1650A01
User Manual of iVMS-5200 Control Client
1
Hikvision® iVMS-5200 Control Client User Manual
This manual, as well as the software described in it, is furnished under license and may be used or copied only in
accordance with the terms of such license. The content of this manual is furnished for informational use only, is
subject to change without notice, and should not be construed as a commitment by Hangzhou Hikvision Digital
Technology Co., Ltd. (Hikvision). Hikvision assumes no responsibility or liability for any errors or inaccuracies that
may appear in the book.
Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system,
or transmitted, in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior
written permission of Hikvision.
HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THE HIKVISION
SOFTWARE. HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE
USE OR THE RESULTS OF THE USE OF THE HIKVISION SOFTWARE IN TERMS OF ITS CORRECTNESS, ACCURACY,
RELIABILITY, CURRENTNESS, OR OTHERWISE. THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF THE
HIKVISION SOFTWARE IS ASSUMED BY YOU. THE EXCLUSION OF IMPLIED WARRANTIES IS NOT PERMITTED BY
SOME STATES. THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, AND THE LIKE) ARISING OUT OF THE USE OR
INABILITY TO USE THE HIKVISION SOFTWARE EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
User Manual of iVMS-5200 Control Client
2
Contents
Chapter 1 Overview ....................................................................................................................... 4
1.1 Description .................................................................................................................... 4
1.2 Running Environment .................................................................................................... 4
1.3 Function Modules ......................................................................................................... 4
Chapter 2 Live View ....................................................................................................................... 7
2.1 Login .............................................................................................................................. 7
2.2 Basic Operations in Live View........................................................................................ 8
2.2.1 Starting and Stopping the Live View ............................................................... 10
2.2.2 Auto-switch in Live View ................................................................................. 11
2.2.3 PTZ Control in Live View .................................................................................. 12
2.2.4 Manual Recording and Capture ....................................................................... 15
2.2.5 Instant Playback .............................................................................................. 18
2.2.6 Other Functions in Live View ........................................................................... 20
Chapter 3 Remote Playback ......................................................................................................... 22
3.1 Normal Playback ......................................................................................................... 22
3.2 Event Playback ............................................................................................................. 25
3.3 POS Playback ............................................................................................................... 26
3.4 Synchronous Playback ................................................................................................. 27
3.5 VCA Playback ............................................................................................................... 27
Chapter 4 E-map Management .................................................................................................... 29
4.1 Adding an E-map ......................................................................................................... 29
4.2 Hot Spot Function ....................................................................................................... 31
4.2.1 Adding Hot Spots ............................................................................................. 32
4.2.2 Modifying Hot Spots ........................................................................................ 34
4.2.3 Previewing Hot Spots ...................................................................................... 35
4.3 Hot Region Function .................................................................................................... 37
4.3.1 Adding Hot Regions ......................................................................................... 37
4.3.2 Modifying Hot Regions .................................................................................... 38
4.3.3 Previewing Hot Regions ................................................................................... 38
4.4 The Preset Function .................................................................................................... 39
Chapter 5 License Plate Recognition ............................................................................................ 40
5.1 Live View ..................................................................................................................... 40
5.2 Searching the License Plate Information ..................................................................... 42
Chapter 6 Alarm Center ............................................................................................................... 43
6.1 Alarm Information of Event ......................................................................................... 44
6.2 Alarm Information of iVMS-5200P .............................................................................. 45
Chapter 7 People Counting Statistics ........................................................................................... 46
Chapter 8 Heat Map ..................................................................................................................... 48
Chapter 9 Log Management ........................................................................................................ 49
Chapter 10 Local Configuration ................................................................................................. 52
10.1 General Settings .......................................................................................................... 52
10.2 File Saving Path Settings .............................................................................................. 53
User Manual of iVMS-5200 Control Client
3
10.3 Keyboard and Joystick Shortcuts Settings ................................................................... 54
10.4 Alarm Sound Settings .................................................................................................. 54
Chapter 11 Status Detection ...................................................................................................... 56
11.1 Physical View ............................................................................................................... 56
11.2 Logical View ................................................................................................................. 57
Chapter 12 Web Client ............................................................................................................... 59
12.1 Login ............................................................................................................................ 59
12.2 Live View ..................................................................................................................... 60
12.3 Playback ...................................................................................................................... 64
12.4 Local Configuration ..................................................................................................... 66
User Manual of iVMS-5200 Control Client
4
Chapter 1 Overview
1.1 Description
As one of the key components of the iVMS-5200 Professional (hereafter simple as iVMS-5200P),
iVMS-5200 Control Client provides multiple operating functionalities, including real-time live view, PTZ
control, video playback and download, alarm receiving, log query, etc..
This user manual describes the function, configuration and operation steps of iVMS-5200 Control
Client. To ensure the proper usage and stability of the client, please refer to the contents below and
read the manual carefully before operation.
Note: Two control clients are available: C/S Control Client (from Chapter 2 to Chapter 11) and B/S Web
Client (Chapter 12).
1.2 Running Environment
Operating System: Microsoft Windows 7 / Windows 8/ Windows 8.1 (32 / 64-bit)
CPU: Intel Core i3-530 and above
Memory: 4GB or above
Video Card: Geforce GTX 240 and above
Note: For high stability and good performance, these above system requirements must be met.
1.3 Function Modules
Control Panel of iVMS-5200 Control Client:
User Manual of iVMS-5200 Control Client
5
Menu Bar:
File
Open Local Picture
Manage the captured pictures stored on local PC.
Open Video File
Manage the video files recorded on local PC.
Exit
Exit the iVMS-5200 Control Client.
System
Lock
Lock screen operations. Or you can click in the
upper-right corner to lock. Click Unlock and input the
password to unlock.
Switch User
Switch the login user.
View
1024*768
Display the window at size of 1024*768 pixels.
1280*1024
Display the window at size of 1280*1024 pixels.
1440*900
Display the window at size of 1440*900 pixels.
1680*1050
Display the window at size of 1680*1050 pixels.
Full Screen
Display the window in full screen.
Control Panel
Enter Control Panel interface.
Main View
Open Main View page.
Remote Playback
Open Remote Playback page.
E-map
Open E-map page.
License Plate Recognition
Open License Plate Recognition page.
Alarm Center
Open the Alarm Center page.
Auxiliary Screen Preview
Open Auxiliary Screen Preview window.
Tool
Log Search
Open the Log Search page.
Local Configuration
Open the Local Configuration page.
Status Detection
Open the Status Detection page.
Broadcast
Select the camera(s) to start broadcasting.
I/O Control
Open / close the alarm outputs.
People Counting
Open the People Counting Statistics page.
Heat Map
Generate the heat map for the camera.
Access Control
Configuration
Open the Access Control Configuration window to check
the information of the connected access control. For
details, please refer to the User Manual of Access Control
System.
Player
Open the player to play the local video files.
Help
User Manual (F1)
Click to open the User Manual; you can also open the User
Manual by pressing F1 on your keyboard.
About
View the basic information of the Control Client and the
License information of the connected iVMS-5200P.
Language
Select the language for the Control Client.
The iVMS-5200 Control Client is composed of the following function modules:
The Main View module provides live view of network cameras and video encoders, and
supports some basic operations, such as picture capturing, recording, PTZ control, etc.
User Manual of iVMS-5200 Control Client
6
The Remote Playback module provides the search, playback, export of record files.
The E-map module provides the displaying and management of E-maps, alarm inputs, hot
regions and hot spots.
The License Plate Recognition module provides the live view and query of the license
plate information.
The Alarm Center module provides the displaying and management of alarm information
received by the Control Client.
The Log Search module provides the query of log files and the log files can be filtered by
different types.
The Local Configuration module provides the configuration of general parameters, file
saving paths, alarm sounds and other settings for the Control Client.
The Status Detection module provides the function of displaying the status of the server,
connected devices and the cameras of the devices.
The function modules are easily accessed by clicking the navigation buttons on the control panel or by
selecting the function module from the View or Tool menu.
You can check the information, including current user, network usage, CPU usage, memory usage and
time, in the upper-right corner of the main page.
User Manual of iVMS-5200 Control Client
7
Chapter 2 Live View
2.1 Login
When opening iVMS-5200 Control Client, you can login with the user name and password of
iVMS-5200P.
Two kinds of user (normal user and domain user) are supported for accessing the iVMS-5200P. Please
refer to the User Manual of iVMS-5200 Professional Web Manager for the detailed introduction.
Option 1: Login with Normal User
Steps:
1. Double-click on the desktop to run the Control Client.
2. Select Normal Login and input the normal user name and password of the iVMS-5200P.
Notes:
By default, the user name of the iVMS-5200P is admin and the password is 12345.
You are highly recommended to change the default password right after the first login to
avoid safety problem. Please refer to the User Manual of iVMS-5200 Professional Web
Manager for the operation of changing password.
3. Optionally, check the checkbox Remember Password to keep the password.
4. Check the checkbox Enable Auto-login to log into the software automatically.
5. Set the address and port No. of the CMS.
Note: If these fields are not displayed, click Show Server Address to show them. You can also click
Hide Server Address to collapse these fields.
Server Address: Enter the address of the CMS that you want to connect to.
Port No.: Enter the port No. of the CMS. By default, it’s 80.
6. Click Login to enter the Control Client.
Option 2: Login with Domain User
Steps:
1. Click Domain Login tab and select the domain user.
2. (Option 1) If you select your own domain account (the current user account that log into your PC),
you can check the Enable Auto-login checkbox to log into the software automatically next time.
3. (Option 2) If you select other user, enter the user name and password. Optionally, you can check
User Manual of iVMS-5200 Control Client
8
the checkbox Remember Password to keep the password and check the Enable Auto-login
checkbox to log into the software automatically next time.
4. Set the address and port No. of the CMS.
Note: If these fields are not displayed, click Show Server Address to show them. You can also click
Hide Server Address to collapse these fields.
Server Address: Enter the address of the CMS that you want to connect to.
Port No.: Enter the port No. of the CMS. By default, it’s 80.
5. Click Login to enter the Control Client.
2.2 Basic Operations in Live View
Purpose:
For the surveillance task, you can view the live video of the added network cameras and video
encoders on the Main View page. And some other basic operations are supported, including picture
capturing, manual recording, PTZ control, etc.
Click the icon on the control panel,
or click View->Main View to open the Main View page.
Main View Page
User Manual of iVMS-5200 Control Client
9
1 View List: Show the customized view and you can also create new view.
2 Camera List: Show the added devices.
3 PTZ Control Panel: Show the panel for PTZ control.
4 Display Window of Live View: The window for playing the live video of the camera(s).
5 Live View Toolbar: The buttons shown are used for controlling the live view.
Camera Status:
The camera is online and works properly.
The camera is in live view.
The camera is in recording status.
The camera is offline.
Live View Toolbar:
On the Main View page, the following buttons are available:
Save View
Save the new settings for the current view.
Save View As
Save the current view as another new view.
Stop Live View
Stop the live view of all cameras.
Mute/Audio On
Turn off/on the audio in live view.
Resume/Pause
Auto-switch
Click to resume/pause the auto-switch in live view.
Show /Hide the Menu
Show/Hide the configuration menu of auto-switch. Click again to
hide.
Previous
Go for live view of the previous page.
Next
Go for live view of the next page.
Screen Layout
Set the screen layout.
Full Screen
Display the live view in full-screen mode. Press ESC key to exit.
Right-click on the display window in live view to open the Live View Management Menu:
The following items are available on the right-click Live View Management Menu:
Stop Live View
Stop the live view in the display window.
Capture
Capture the picture in the live view process.
User Manual of iVMS-5200 Control Client
10
Print Captured Picture
Capture the current picture and then print the picture.
Start/Stop Recording
Start/Stop the manual recording. The record file is stored in the PC.
Open PTZ Control
Enable PTZ control function on the display window. Click again to
disable the function.
Open Digital Zoom
Enable the digital zoom function. Click again to disable the function.
Switch to Instant
Playback
Switch to instant playback mode. You can select the playback time.
Start/Stop Two-way
Audio
Click to start/stop the two-way audio of the camera in live view.
Enable/Disable Audio
Click to enable/disable the audio in live view.
Camera Status
Display the status of the camera in live view, including the recording
status, signal status, connection number, etc.
Arming Control
Open the arming control window of the camera in live view.
Full Screen
Display the live view in full-screen mode. Click the icon again to exit.
2.2.1 Starting and Stopping the Live View
Starting Live View for One Camera
Steps:
1. Open the Main View page.
2. Optionally, click and select the screen layout mode for live view.
3. Click-and-drag the camera to the display window,
or double-click the camera name after selecting the display window to start the live view.
Notes:
You can click-and-drag the video of the camera in live view to another display window if needed.
For the device that supports POS (Point of Sales) text overlay, you can view the POS text
displaying on the live video if the POS settings are properly configured. You can configure the
POS settings via Web Manager (Resource Management->Physical View->Remote Configuration).
For detailed settings, please refer to the User Manual of the device.
Starting Live View for Area
Steps:
1. Open the Main View page.
2. Click-and-drag the area to the display window,
or double-click the area name to start the live view. You can also click-and-drag or double-click
the ControlCenter node to start the live view of all the added devices.
Note: The display window number is self-adaptive to the camera number of the area.
Starting Live View in Custom View Mode
Purpose:
The view mode can be customized for the video live view.
Note: The custom view you created will be saved to the iVMS-5200P and other users who have the
User Manual of iVMS-5200 Control Client
11
corresponding permission can also get access to the view and the related live video.
Steps:
1. Open the Main View page.
2. In the view panel, select the View node and click the icon activate the view adding dialog
box.
3. Input the view name and click Add. The new view is of 4-Screen mode by default.
4. Optionally, Click the icon in live view toolbar and select the screen layout mode for the new
view.
5. Click to save the screen layout mode for the new view.
6. Click-and-drag the camera to the display window,
or double-click the camera name in custom view mode to start the live view.
7. Click the icon to save the new view. Optionally, you can click to save the current view as
another view.
After successfully settings the view, you can click to call the view.
Move the mouse onto the custom view, the following icons are available:
Edit View Name
Edit the name of the custom view.
Delete View
Delete the custom view.
Instant Playback
Start the instant playback of the cameras related to the view. Up
to 16 cameras can be switch to instant playback at the same
time.
Stopping the Live View
Steps:
1. Select the display window.
2. Click the icon that appears in the upper-right corner when the mouse pointer is over the
display window,
or click Stop Live View on the right-click menu to stop the live view of the display window.
You can also click the button in live view toolbar to stop all the live view.
2.2.2 Auto-switch in Live View
Camera Auto-switch
Purpose:
The video stream of the cameras from the same area will switch automatically in a selected display
window in camera auto-switch.
Steps:
1. Open the Main View page.
2. Select a display window for camera auto-switch.
3. Click the icon in the toolbar and select the switching interval.
4. Select an area and click the icon on the area node.
5. You can click the icon / to pause/resume the camera auto-switch.
User Manual of iVMS-5200 Control Client
12
View Auto-switch
Purpose:
The custom views will switch automatically in view auto-switch. The custom views need to be added
before proceeding.
Steps:
1. Open the Main View page.
2. Click the icon in the toolbar and select the switching interval.
3. Click the icon on the public view node.
Note: If the number of the cameras is greater than that of the windows, the auto-switch will be
performed in multiple windows. You can click or to view the auto-switch.
4. You can click the icon / to pause/resume the multi-view auto-switch.
All Cameras Auto-switch
Purpose:
The video stream of all the added cameras will switch automatically in a selected display window in all
cameras auto-switch.
Steps:
1. Open the Main View page.
2. Select a display window for all cameras auto-switch.
3. Click the icon in the toolbar and select the switching interval.
4. Click the icon on the ControlCenter node.
Note: If the number of the cameras is greater than that of the windows, the auto-switch will be
performed in multiple windows. You can click or to view the auto-switch.
5. You can click the icon / to pause/resume the auto-switch of all the cameras.
2.2.3 PTZ Control in Live View
The software provides PTZ control for cameras with pan/tilt/zoom functionality. You can set the preset,
patrol and pattern for the cameras on the PTZ Control panel. And you can also open window PTZ
control for the operations of PTZ cameras by clicking Open PTZ Control on the right-click menu.
Click the icon to expand the PTZ Control panel.
User Manual of iVMS-5200 Control Client
13
The following buttons are available on the PTZ Control panel:
Direction Button and Auto-scan
Zoom
Focus
Iris PTZ Speed
Auxiliary Focus
3D Positioning
Light
Wiper
Lens Initialization
Configuring the Preset
A preset is a predefined image position which contains information of pan, tilt, zoom, focus and other
parameters.
Perform the following steps to add a preset:
1. Click the Preset tab to enter the PTZ preset configuration panel.
2. Click the direction buttons on the PTZ control panel to move the camera to the desired view.
3. Select a PTZ preset number from the preset list and click .
4. Input the name of the preset in the pop-up dialog box.
5. Click OK to save the settings.
To call a configured preset, double-click the preset, or select the preset and click the icon .
To modify a configured preset, select the preset from the list and click the icon .
To delete a configured preset, select the preset from the list and click the icon .
User Manual of iVMS-5200 Control Client
14
Configuring the Pattern
Patterns can be set to record the movement of the PTZ.
Perform the following steps to add a pattern:
1. Click the Pattern button to enter the PTZ pattern configuration panel.
2. Click to start recording of this pattern path.
3. Use the direction buttons and other buttons to control the PTZ movement.
4. Click to stop and save the pattern recording.
5. Click the icon to call the pattern. To stop calling the pattern, click .
Note: Only one pattern can be configured, and the newly-defined pattern will overwrite the previous
one.
Configuring the Patrol
A patrol is a scanning track specified by a group of user-defined presets, with the scanning speed
between two presets and the dwell time at the preset separately programmable.
Before you start:
Two or more presets for one PTZ camera need to be added.
Perform the following steps to add and call a patrol:
1. Click the Patrol button to enter the PTZ patrol configuration panel.
2. Select a path number from the drop-down list.
User Manual of iVMS-5200 Control Client
15
3. Click to add a preset, and set the dwell time and patrol speed.
4. Repeat the above operation to add other presets to the patrol.
5. Optionally, you can click or to edit or delete a preset in the patrol path.
6. Click the icon to call the patrol. To stop calling the patrol, click .
Notes:
Up to 16 patrols can be configured.
The preset dwell time can be set to 1~30 seconds, and the patrol speed can be set to level 1~40.
2.2.4 Manual Recording and Capture
Toolbar in Each Live View Display Window:
In each live view display window, the following toolbar buttons are available:
Capture
Capture the picture of the camera during live view.
Start/Stop Recording
Start/Stop manual recording. The record file is stored in the PC.
Switch to Instant
Playback
Switch to the instant playback mode. You can select the playback
time.
Manual Recording in Live View
Purpose:
Manual Recording function allows you to record the live video on the Main View page manually and
the record files are stored in the local PC.
Steps:
1. Move the mouse pointer to the display window in live view to show the toolbar.
2. Click in the toolbar of the display window or on the right-click Live View Management Menu
to start the manual recording. The icon turns to .
3. Click the icon to stop the manual recording.
A prompt box with the saving path of the video files you just recorded will pop up if all the
operations succeed.
Notes:
During the manual recording, an indicator appears in the upper-right corner of the display
User Manual of iVMS-5200 Control Client
16
window.
The saving path of video files can be set on the Local Configuration interface. For details, see
Section 10.2 File Saving Path Settings.
Viewing Local Record Files
Steps:
1. Click File->Open Video File to open the Record Files page.
2. Select the camera to be searched from the Area list.
3. Click the icon to specify the start time and end time for the search.
4. Click Search. The video files recorded between the start time and end time will be displayed.
Select the video file, and click Upload. You can upload the video file to the configured FTP
server. You can also click Upload Queue to check the uploading status.
Select the video file, and click Burn. You can burn the record file to a disc connected to your PC.
You can also click Burning Progress to view the burning status.
Select the video file, and click Save as. You can save a new copy of the video file in local PC.
Select the video file, and click Delete. You can delete the video file.
Note: To upload the video files to FTP server, the FTP settings need to be configured before
proceeding. For details, see Section 10.2 File Saving Path Settings.
Double-click the video file and the video file can be played back locally.
User Manual of iVMS-5200 Control Client
17
The following buttons are available on the local playback page:
CIF/4CIF
Display the video at CIF/4CIF resolution.
Full Screen
Display the local playback page in full-screen mode.
Close
Close the local playback page of the record file.
Pause/Play
Pause / resume the playback of the record file.
Stop
Stop the playback of the record file.
Speed
Set the playback speed.
Single Frame
Play back the record file frame by frame.
Digital Zoom
Enable the digital zoom function. Click again to disable.
Enable/Disable Audio
Click to enable/disable the audio in the local playback.
Capture
Capture the picture of the playback video.
Capturing Picture in Live View
Steps:
1. Move the mouse pointer to the display window in live view to show the toolbar.
2. Click the icon in the toolbar of the display window or on the right-click Live View
Management Menu.
A small window of the captured picture will be displayed to notify whether the capturing
operation is done or not.
Note: The saving path of the captured pictures can be set on the Local Configuration interface. For
details, see Section 10.2 File Saving Path Settings.
Viewing Captured Pictures
The pictures captured in live view are stored in the PC running the Control Client. You can view the
captured pictures if needed.
Steps:
1. Click File->Open Local Picture to open the Captured Picture page.
2. Select the camera to be searched from the Area list.
3. Click the icon to specify the start time and end time for the search.
User Manual of iVMS-5200 Control Client
18
4. Click Search. The pictures captured between the start time and end time will be displayed.
5. Double-click the captured picture to enlarge it for a better view.
Select the captured picture, and click Upload. You can upload the picture to the configured FTP
server. You can also click Upload Queue to check the uploading status.
Select the captured picture, and click Burn. You can burn the picture to a disc connected to
your PC. You can also click Burning Progress to view the burning status.
Select the captured picture, and click Print. You can print the selected picture by the printer
connected via the network.
Select the captured picture, and click Save as. You can save a new copy of the picture in local
PC.
Select the captured picture, and click Delete. You can delete the selected picture.
Note: To upload the pictures to FTP server, the FTP settings need to be configured before
proceeding. For details, see Section 10.2 File Saving Path Settings.
2.2.5 Instant Playback
Purpose:
The record files can be played back instantly on the Main View page. Instant playback only shows the
record in last 30s/1min./3min./5min./8min./10min. If no record is found, it means there is no record
during the last 30s/1min./3min./5min./8min./10min. Thus, you can get an immediate review if
needed.
Before you start:
The video files need to be recorded on the storage devices, such as the SD/SDHC cards and HDDs
on the DVRs, NVRs, Network Cameras, etc., or on the storage servers.
You should configure the record schedule for the device via Web Manager. For details, please
refer to User Manual of iVMS-5200 Professional Web Manager.
Steps:
1. Start the live view and move the mouse pointer to the display window to show the toolbar.
2. Click the icon on the toolbar or on the right-click Live View Management Menu, and a list of
time periods pops up.
30s, 1 min, 3 min, 5 min, 8 min, and 10 min are selectable.
User Manual of iVMS-5200 Control Client
19
3. Select a time period to start the instant playback.
Example: If the current time of the live view is 09:30:00, and you select 3 min, then the instant
playback will start from 09:27:00.
4. Click the icon again to stop the instant playback and go back for the live view.
Notes:
During the instant playback, an indicator appears in the upper-right corner of the display
window.
You should click to go back to the live view process after the instant playback completed.
The following buttons are available on the playback control bar:
Reverse
Playback
Play back the record file reversely.
Pause/Start
Playback
Pause / Start the playback of the record files.
Speed Down /
Up
Decrease / Increase the play speed of the instant playback.
Stop Playback
Stop the playback of all cameras.
Single Frame
Play back the record files frame by frame.
Capture
Capture the picture of the camera during instant playback.
Start/Stop
Recording
Start/Stop manual recording. The record file is stored in the PC.
Switch to Live
View
Switch to the live view mode.
Right-click on the display window during instant playback to activate the following menu:
User Manual of iVMS-5200 Control Client
20
The following buttons are available on the right-click Instant Playback Management Menu:
Reverse Playback
Play back the record file reversely.
Pause/Play
Pause/Start the instant playback in the display window.
Stop
Stop the instant playback and return to the live view mode.
Speed Up/Down
Increase/Decrease the play speed of the instant playback.
Single Frame
Play back the record file frame by frame.
Open Digital Zoom
Enable the digital zoom function. Click again to disable the function.
Capture
Capture the picture in the instant playback process.
Print Captured Picture
Capture the current picture and then print the picture.
Start/Stop Recording
Start/Stop clipping the record files.
Enable/Disable Audio
Click to turn on/off the audio in instant playback.
Switch to Live View
Switch to live view mode.
Full Screen
Display the instant playback in full screen mode. Click again to exit.
2.2.6 Other Functions in Live View
There are some other functions supported in the live view, including digital zoom, two-way audio, and
camera status.
Auxiliary Screen Preview
The live video can be displayed on different auxiliary screens for the convenient preview of multiple
monitoring scenes. Click View->Auxiliary Screen Preview to open an auxiliary screen. Up to 3 auxiliary
screens are supported.
Digital Zoom
Right-click on the live view window and select Open Digital Zoom. Use the left key of mouse to drag a
rectangle area in the lower-right/upper-left direction, and then the rectangle area will zoom in/out.
Two-way Audio
Loading...