HIKVISION iDS-2CD9136-AIS, iDS-2CD9396-AIS, iDS-2CD9136-AS, iDS-2CD9396-AS User Manual
Network Traffic Camera • User Manual
Network Traffic Camera
User Manual
Network Traffic Camera • User Manual
1
© 2019 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved.
This Manual is the property of Hangzhou Hikvision Digital Technology Co., Ltd. or its affiliates (hereinafter referred to as
“Hikvision”), and it cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without
the prior written permission of Hikvision. Unless otherwise expressly stated herein, Hikvision does not make any
warranties, guarantees or representations, express or implied, regarding to the Manual, any information contained
herein.
About this Manual
The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information
hereinafter are for description and explanation only. The information contained in the Manual is subject to change,
without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision
website (https://www.hikvision.com/en/).
Please use this Manual with the guidance and assistance of professionals trained in supporting the Product.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properties of Hikvision in various jurisdictions.
Other trademarks and logos mentioned are the properties of their respective owners.
LEGAL DISCLAIMER
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH
ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH ALL FAULTS AND ERRORS”.
HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY,
SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR
OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS
INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED
ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN
CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES OR LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION
SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES
RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY
RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE
RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD
PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA
PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES,
INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR
PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY
NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Network Traffic Camera • User Manual
2
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and
comply therefore with the applicable harmonized European standards listed under the
EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as
unsorted municipal waste in the European Union. For proper recycling, return this product
to your local supplier upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that cannot be disposed
of as unsorted municipal waste in the European Union. See the product documentation
for specific battery information. The battery is marked with this symbol, which may include
lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the
battery to your supplier or to a designated collection point. For more information see:
www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
Network Traffic Camera • User Manual
3
Applicable Models
This manual is applicable to the models listed in the following table.
Model
iDS-2CD9136-AIS
iDS-2CD9396-AIS
iDS-2CD9136-AS
iDS-2CD9396-AS
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Safety Instructions
To reduce the risk of fire or electrical shock, do not expose this product to rain or moisture.
This installation should be made by a qualified service person and should conform to all the
local codes.
Please install blackouts equipment into the power supply circuit for convenient supply
interruption.
If the product does not work properly, please contact your dealer or the nearest service
center. Never attempt to disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or maintenance.)
Preventive and Cautionary Tips
Make sure the power supply voltage is correct before using the camera.
Symbol
Description
Provides additional information to emphasize or supplement
important points of the main text.
Indicates a potentially hazardous situation, which if not avoided,
could result in equipment damage, data loss, performance
degradation, or unexpected results.
Indicates a hazard with a high level of risk, which if not avoided, will
result in death or serious injury.
Network Traffic Camera • User Manual
4
Do not drop the camera or subject it to physical shock.
Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit
of ethanol and wipe it gently. If the camera will not be used for an extended period of time,
put on the lens cap to protect the sensor from dirt.
Do not aim the camera lens at the strong light such as sun or incandescent lamp. The strong
light can cause fatal damage to the camera.
The sensor may be burned out by a laser beam, so when any laser equipment is being used,
make sure that the surface of the sensor not be exposed to the laser beam.
Do not place the camera in extremely hot, cold temperatures, dusty or damp environment,
and do not expose it to high electromagnetic radiation.
To avoid heat accumulation, good ventilation is required for a proper operating environment.
Keep the camera away from water and any liquid.
While shipping, the camera should be packed in its original packing.
Network Traffic Camera • User Manual
5
TABLE OF CONTENTS
Chapter 1 Network Connection ...................................................................................................... 7
Wiring over the LAN ............................................................................................................ 7
Activate the Camera ............................................................................................................ 8
Activation via Web Browser ........................................................................................ 8
Activation via SADP Software ...................................................................................... 9
Chapter 2 Login............................................................................................................................. 11
Chapter 3 Live View ...................................................................................................................... 12
Live View Page ................................................................................................................... 12
Start Live View ................................................................................................................... 13
Record and Capture Pictures Manually .............................................................................. 13
View Live Status and Traffic Statistics ................................................................................. 13
Scene Shot Area ........................................................................................................ 14
Traffic Light Status ..................................................................................................... 16
Traffic Statistics ......................................................................................................... 16
Chapter 4 Picture Search .............................................................................................................. 17
Chapter 5 Local Configuration ...................................................................................................... 18
Chapter 6 System Configuration ................................................................................................. 20
View Device Information ................................................................................................... 20
Configure Installation Parameters ...................................................................................... 21
Configure Serial Ports ........................................................................................................ 22
Configure Network Parameters .......................................................................................... 23
Configure Port ................................................................................................................... 25
Configure HTTPS ................................................................................................................ 25
Configure Time .................................................................................................................. 27
Enable User Lock ............................................................................................................... 29
Chapter 7 Encoding and Storage Configuration ............................................................................ 30
Configure Video Encoding .................................................................................................. 30
Configure Image Encoding ................................................................................................. 32
Configure ROI .................................................................................................................... 32
Configure Record Schedule ................................................................................................ 34
Configure Storage Management ........................................................................................ 35
Configure FTP .................................................................................................................... 36
Chapter 8 Text Overlay Configuration ........................................................................................... 40
Configure Capture Picture Overlay ..................................................................................... 40
Configure OSD Settings ...................................................................................................... 43
Configure Composite Picture Overlay ................................................................................ 44
Chapter 9 Capture Parameters Configuration ............................................................................... 45
Configure License Plate Parameters ................................................................................... 45
Configure Flash Light Parameters ....................................................................................... 45
Configure Traffic Light Synchronization .............................................................................. 48
Configure Image Composition ............................................................................................ 49
Network Traffic Camera • User Manual
6
Configure Vehicle Feature .................................................................................................. 51
Chapter 10 Image Parameters Configuration ................................................................................ 54
Configure Dual-Shutter Parameters ................................................................................. 54
Configure General Parameters ......................................................................................... 55
Configure Video Image .................................................................................................... 56
Configure Record ............................................................................................................. 57
Configure ICR ................................................................................................................... 58
Configure Light Calibration .............................................................................................. 59
Chapter 11 Application Mode Configuration ................................................................................ 61
Mixed-traffic Lane ............................................................................................................ 61
Configure Video Analysis Capture ........................................................................... 61
Configure Mixed-Traffic Lane................................................................................... 62
Video Analysis E-Police .................................................................................................... 64
Configure Video Analysis Capture ........................................................................... 65
Configure Lane Parameters and Trigger Rules ........................................................ 66
Configure Traffic Light ............................................................................................. 68
External Input .................................................................................................................. 71
Checkpoint Vehicle Detector ............................................................................................ 73
RS-485 Radar ................................................................................................................... 76
Chapter 12 Exception.................................................................................................................... 81
Chapter 13 Maintenance .............................................................................................................. 83
Device Status ................................................................................................................... 83
User Management ........................................................................................................... 83
Add a User .............................................................................................................. 84
Modify a User ......................................................................................................... 85
Delete a User .......................................................................................................... 86
Log Search ....................................................................................................................... 86
Reboot the Camera .......................................................................................................... 87
Restore Default Settings................................................................................................... 87
Export Debug File ............................................................................................................ 88
Export Configuration File ................................................................................................. 88
Import the Configuration File ........................................................................................... 88
Upgrade the System......................................................................................................... 89
Network Traffic Camera • User Manual
7
Chapter 1 Network Connection
You shall acknowledge that the use of the product with Internet access might be under
network security risks. For avoidance of any network attacks and information leakage,
please strengthen your own protection. If the product does not work properly, please
contact with your dealer or the nearest service center.
To ensure the network security of the camera, we recommend you to have the camera
assessed and maintained termly. You can contact us if you need such service.
Purpose:
To view and configure the camera via a LAN, you need to connect the camera in the same subnet
with your computer, and install the SADP to search and change the IP address of the camera.
Wiring over the LAN
The following figures show the two ways of cable connection of a camera and a computer.
Purpose:
To test the camera, you can directly connect the camera to the computer with a network
cable.
Set camera over the LAN via a switch or a router.
Network Cable
Computer
Traffic Camera
Connecting Directly
Network Traffic Camera • User Manual
8
Switch
ComputerTraffic Camera
Connecting via a Switch or a Router
Activate the Camera
You are required to activate the camera first by setting a strong password for it before you can use
the camera.
Activation via Web Browser and Activation via SADP Software are supported.
Activation via Web Browser
Power on the camera, and connect the camera to the network.
Input the IP address into the address bar of the web browser, and press Enter to enter the
activation interface.
Activation Interface (Web)
Network Traffic Camera • User Manual
9
Create a password and input the password into the password field.
STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your
own choosing (using a minimum of 8 characters, including upper case letters, lower case letters,
numbers, and special characters) in order to increase the security of your product. And we
recommend you reset your password regularly, especially in the high security system, resetting the
password monthly or weekly can better protect your product.
Confirm the password.
Click OK to save the password and enter the live view interface.
Activation via SADP Software
SADP software is used for detecting the online device, activating the camera, and resetting the
password.
Get the SADP software from the official website, and install the SADP according to the prompts.
Run the SADP software to search the online devices.
Check the device status from the device list, and select the inactive device.
SADP Interface
Create a password and input the password in the password field, and confirm it.
Click Activate to activate the device.
Network Traffic Camera • User Manual
10
STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your
own choosing (using a minimum of 8 characters, including upper case letters, lower case letters,
numbers, and special characters) in order to increase the security of your product. And we
recommend you reset your password regularly, especially in the high security system, resetting the
password monthly or weekly can better protect your product.
Change the device IP address to the same subnet with your computer by either modifying
the IP address manually.
Create Password
Input the password and click Modify to activate your IP address modification.
Network Traffic Camera • User Manual
11
Chapter 2 Login
Open the web browser.
In the browser address bar, input the IP address of the camera, and press the Enter key to
enter the login interface.
Input User Name and Password.
Click Login.
Login
Install the plug-in before viewing the live video and operating the camera. Follow the
installation prompts to install the plug-in.
You may have to close the web browser to install the plug-in. Please reopen the web browser and
log in again after installing the plug-in.
Network Traffic Camera • User Manual
12
Chapter 3 Live View
Live View Page
Purpose:
The live view page allows you to view the real-time video and capture images.
Log in the camera to enter the live view page, or you can click Live View on the menu bar of the
main page to enter the live view page.
Live View Page
Refer to the following table for the description of the icons on the live view page.
Network Traffic Camera • User Manual
13
Descriptions of Live View Icons
Icon
Description
/
Start/Stop live view.
The window size is 4:3.
The window size is 16:9.
The original widow size.
Self-adaptive window size.
Live view with the main stream. If the network is in
good condition, select main stream.
Live view with the sub stream.
Start/Stop audio and adjust the volume.
/
Enable/Disable two-way audio.
Manually capture the picture.
Manually start/stop recording.
/
Turn on/off digital zoom function.
Enter the Real-Time Status and Traffic Flow
Statistics page.
Start Live View
On the live view page, click “ ” on the toolbar to start the live view of the camera.
Record and Capture Pictures Manually
On the live view page, click “ ” on the toolbar to capture the live pictures or click “ ” to start
recording. The saving paths of the captured pictures and recorded videos can be set on the
Configuration > Local Configuration page.
The captured image will be saved as JPEG file in your computer.
View Live Status and Traffic Statistics
Click Real-Time Status and Traffic Flow Statistics on the upper right of the live view window to
enter the live status and traffic statistics configuration page.
Network Traffic Camera • User Manual
14
Real-Time Status and Traffic Flow Statistics
Scene Shot Area
Arm the camera.
− Level 1 Arming: The camera is allowed to connect to only one data storage device for
image, video and information uploading. It is recommended when you
develop products, that is, if you use SDK, level 1 arming is the only option.
− Level 2 Arming: The camera is allowed to connect to three data storage devices for image
and information uploading, such as PC, platform and terminal server.
− Disarming: The camera is not allowed to connect to any data storage devices.
Level 2 Arming is recommended for debugging. Because when the device is running, Level 1
Arming cannot be activated.
Measuring License Plate: Measure the pixel of the captured license plate. You can click Closing
Measurement to disable the function.
Ruler On: Enable ruler to measure the length of the captured license plate. You can click Ruler
Off to disable the function.
Open Folder: Open the folder that saves the captured pictures.
Capture: Click Capture to capture the picture, and the captured pictures will be listed in the
Picture List.
Network Traffic Camera • User Manual
15
Picture List
Description of Picture List Parameters
Item
Description
No.
Picture No.
Capture Time
The time of capturing the picture with millisecond
precision. For example, 20150915111054738 means
the picture is captured at 11:10:54:738, on September
15th, in 2015.
Lane No.
The lane where the vehicle is captured.
License Plate Color
The color of the captured license plate.
License Plate Number
The license plate number of the vehicle.
Speed
The speed of the captured vehicle.
Illegal Type
The captured type, normal, over speed, wrong
direction are selectable.
Vehicle No.
The vechile counting No. ranging from 1 to 65535. It
will overwrite if it reachs the max. value.
Directory
The file path of the saved picture.
Continuous Capture: Click Continuous Capture to capture pictures continuously, and click “ ”
to set continuous capture parameters including Lane No., Waiting Time, Capture Times, and
Continuous Capture Interval.
Set Continuous Capture Parameters
Lane No.: The lane where the vehicle is captured.
Waiting Time: Delay time from capture order had been delivered to vehicle was actual
captured.
Capture Times: Number of captured pictures.
Continuous Capture Interval: The time interval of the continuous pictures are captured
Network Traffic Camera • User Manual
16
Traffic Light Status
Traffic Light Status display the current traffic light status after setting.
Traffic Light Status
The Traffic light status can only be applied in Video Analysis E-police mode.
Traffic Statistics
Purpose:
The traffic statistics allows you to view the real-time traffic flow, average lane occupancy, and then
analyze the real-time traffic status.
Before you start:
Go to Configuration > Device Configuration> System Configuration> Traffic Parameters.
Check Enable, and set Traffic Statistics Interval.
Click Real-Time Status and Traffic Flow Statistics > Traffic Statistics, you can view the Start Time,
Lane No., Traffic Flow, Average Lane Occupancy, Average Speed and Average Time Headway.
Network Traffic Camera • User Manual
17
Chapter 4 Picture Search
Purpose:
The captured picture of all types, including normal, overspeed, wrong-way driving, etc., can be
searched from this page. You can also export the pictures to the PC local directory.
Before you start:
Please insert a TF card with up to 128 GB storage in the camera for picture storage. Picture cannot
be searched if there is no TF card.
Click Picture on the menu bar to enter picture searching page.
Search Picture
Set the picture search conditions, including Lane No., Vehicle Type, Violation Type, Car
Plate, Start Time, and End Time.
Click Search to search pictures. The matched pictures will be displayed in Picture List.
Click Export Picture to export the pictures to your PC.
Network Traffic Camera • User Manual
18
Chapter 5 Local Configuration
Purpose:
The local configuration refers to the parameters of the live view, record files and captured pictures.
The record files and captured pictures are the ones you record and capture using the web browser
and thus the saving paths of them are on the PC running the browser.
Go to Configuration > Local.
Configure the following settings:
Live View Parameters: Set the protocol type and live view performance.
− Protocol: TCP and UDP are selectable.
TCP: Ensures complete delivery of streaming data and better video quality,
yet the real-time transmission will be affected.
UDP: Provides real-time audio and video streams.
− Live View Performance: Set the live view performance to Least Delay, Balanced, Best
Fluency.
− Rule Information: It refers to the rules on your local browser, select enable to display the
colored marks when the motion detection, face detection, or intrusion
detection is triggered. E.g., enabled as the rules are, and the face detection
is enabled as well, when a face is detected, it will be marked with a green
rectangle on the live view.
− Feature Information: Enable the function, feature information of the detected target is
dynamically displayed near the target in the live image.
The feature information of different functions is different. For example, ID
and waiting time for Queue Management, height for People Counting, etc.
Feature Information is only available for certain camera models.
Live View Parameters
Record File Settings: Set the saving path of the recorded video files. Valid for the record files
you recorded with the web browser.
Network Traffic Camera • User Manual
19
− Record File Size: Select the packed size of the manually recorded and downloaded video
files. After the selection, the maximum record file size is the value you
selected.
− Save record files to: Set the saving path for the manually recorded video files.
Picture and Clip Settings: Set the saving paths of the captured pictures and clipped video files.
Valid for the pictures you capture with the web browser.
− Save snapshots in live view to: Set the saving path of the manually captured pictures in
live view mode.
− Save download pictures to: Set the saving path of the download pictures.
− Save scene picture to: Set the saving path of the scene pictures.
You can click Browse to change the directory for saving the clips and pictures.
Click Save to save the settings.
Network Traffic Camera • User Manual
20
Chapter 6 System Configuration
Purpose:
You can configure the parameters on this page, including device information, serial ports, network
parameters, time configuration, service, etc.
View Device Information
Go to Configuration > Device Configuration > System Configuration > Device Information.
Device Name and Device No. can be changed as desired.
Other information of the camera, such as Model, Serial No., Firmware Version, Encoding
Version, Hardware Version, Number of Channels, Number of Alarm Input, Number of Alarm
Output, and Smart Module Status are displayed for your reference. And the information
cannot be edited in this menu.
Algorithms Library Version information can be viewed but cannot be edited in this menu.
Network Traffic Camera • User Manual
21
Device Information
Configure Installation Parameters
You can set the installation parameters of the camera.
Go to Configuration > Device Configuration > System Configuration > Installation
Parameters.
Network Traffic Camera • User Manual
22
Installation Parameters
Set the installation parameters according to the actual conditions.
Click Save to save the settings.
Configure Serial Ports
Purpose:
Configure the RS-485 parameters and RS-232 parameters in this page.
The RS-485 ports are used to input signals related to traffic control, such as RS-485 radar and
vehicle detector. The number of available RS-485 ports can be different according to different
camera models.
The RS-232 port can be used in two ways:
− Parameters Configuration: Connect a computer to the camera through the serial port.
Device parameters can be configured by using software such as
HyperTerminal. The serial port parameters must be the same as the
seriaport parameters of the camera.
− Transparent Channel: Connect a serial device directly to the camera. The serial device will
be controlled remotely by the computer through the network.
Go to Configuration > Device Configuration > System Configuration > Serial Ports.
Network Traffic Camera • User Manual
23
Serial Ports Settings
Configure the RS-485 and RS-232 parameters.
Click Save to save the settings.
Configure Network Parameters
Purpose:
Network parameters settings must be properly configured before you operate the camera over
network. The camera supports both the IPv4 and IPv6. Both versions can be configured
simultaneously without conflicting to each other, and at least one IP version should be configured.
Go to Configuration > Device Configuration > System Configuration > Network Parameters.
Network Traffic Camera • User Manual
24
TCP/IP Settings
Configure the basic network settings, including the NIC Type, IPv4 or IPv6 Address, IPv4 or
IPv6 Subnet Mask, IPv4 or IPv6 Default Gateway, IPv6 mode, Mac Address, MTU settings and
Multicast Address.
ANPR IP Address: ANPR listening IP address. Picture can be transferred from camera to server
by setting ANPR IP address and ANPR port in ANPR protocol.
ANPR Port: ANPR listening port. Picture can be transferred from camera to server by setting
ANPR IP address and ANPR port in ANPR protocol.
Listening Host IP Address: Picture can be transferred from camera to server by setting listening
host IP address and listening host port.
Listening Host Port: Picture can be transferred from camera to server by setting listening host
IP address and listening host port.
ANPR listening will be prior listening when ANPR listening and listening are both set.
If you want to set Listening as prior listening, check Picture Uploading Listening, and set
ANPR listening and listening.
Configure the DNS server. Enter the preferred DNS server.
DNS (Domain Name System) is a network system used to translate names into IP address.
Click Save to save the above settings.
Network Traffic Camera • User Manual
25
The valid value range of MTU is 1280 to 1500.
The Multicast sends a stream to the multicast group address and allows multiple clients to
acquire the stream at the same time by requesting a copy from the multicast group
address. Before utilizing this function, you have to enable the Multicast function of your
router.
A reboot is required for the settings to take effect.
Configure Port
Purpose:
Configure the HTTP port, RTSP port, SDK port information to connect corresponding client.
Go to Configuration > Device Configuration > System Configuration > Port.
Port Configuration
Configure the following parameters.
HTTP Port: The default port number is 80, and it can be changed to any port No. ranges from 1
to 65536 which is not occupied, except 21 (FTP port) and 23 (Telnet port).
RTSP Port: The default port number is 554 and it can be changed to any port No. ranges from
1 to 65536 which is not occupied, except 21 (FTP port) and 23 (Telnet port).
SDK Port: The default server port number is 8000, and it can be changed to any port No.
ranges from 2000 to 65535 which is not occupied.
Click Save to save the settings.
Configure HTTPS
Purpose:
HTTPS provides authentication of the web site and associated web server that one is
communicating with, which protects against Man-in-the-middle attacks. Perform the following
steps to set the port number of https.
Network Traffic Camera • User Manual
26
Example
If you set the port number as 443 and the IP address is 192.168.1.64, you may access the device by
inputting https://192.168.1.64:443 via the web browser.
The HTTPS port can be only configured through the web browser.
Go to Configuration > Device Configuration > System Configuration > HTTPS.
HTTPS Configuration
Create and install the certificate.
OPTION 1: Create private certificate.
1) Click Create private certificate.
2) Click Create and the following message box pops up as below.
Create Private Certificate
3) Enter the parameters.
4) Click OK to save the settings.
OPTION 2: Signed certificate is available. Start the installation directly.
1) Click Signed certificate is available. Start the installation directly.
2) Click View to find the saving path of the certificate.
Loading...