HIKVISION DS-7204HFI-SH, DS-7300-SH, DS-7208HFI-SH, DS-7216HFI-SH, DS-7204HWI-SH User Manual

...

Digital Video Recorder

User Manual

UD.6L0202D1360A01

User Manual of DS-7200/7300/8100-SH Series DVR

Hikvision® Network Digital Video Recorder User’s Manual

This manual, as well as the software described in it, is furnished under license and may be used or copied only in accordance with the terms of such license. The content of this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Hikvision Digital Technology Co., Ltd. (Hikvision). Hikvision assumes no responsibility or liability for any errors or inaccuracies that may appear in the book.

Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of Hikvision.

HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THE HIKVISION SOFTWARE. HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE HIKVISION SOFTWARE IN TERMS OF ITS CORRECTNESS, ACCURACY, RELIABILITY, CURRENTNESS, OR OTHERWISE. THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF THE HIKVISION SOFTWARE IS ASSUMED BY YOU. THE EXCLUSION OF IMPLIED WARRANTIES IS NOT PERMITTED BY SOME STATES. THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.

IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, AND THE LIKE) ARISING OUT OF THE USE OR INABILITY TO USE THE HIKVISION SOFTWARE EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.

User Manual of DS-7200/7300/8100-SH Series DVR

Regulatory information FCC information

FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.

User Manual of DS-7200/7300/8100-SH Series DVR

Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.

This manual is applicable to the following models:

Type

Model

Network HDVR

DS-7204HFI-SH, DS-7208HFI-SH, DS-7216HFI-SH

DS-7204HWI-SH, DS-7208HWI-SH, DS-7216HWI-SH

DS-7204HVI-SV, DS-7208HVI-SV, DS-7216HVI-SV

DS-7208HWI-SL, DS-7216HWI-SL

DS-7304HFI-SH, DS-7308HFI-SH, DS-7316HFI-SH

DS-7304HWI-SH, DS-7308HWI-SH, DS-7316HWI-SH

Network DVR

DS-7204HVI-SH, DS-7208HVI-SH, DS-7216HVI-SH

DS-7204HWI-SV

DS-7224HVI-SH, DS-7232HVI-SH

DS-7224HWI-SH, DS-7232HWI-SH

DS-7324HFI-SH, DS-7332HFI-SH

DS-7324HWI-SH, DS-7332HWI-SH

DS-7324HI-SH, DS-7332HI-SH

DS-8124HCI-SH, DS-8132HCI-SH

DS-8124HFSI-SH, DS-8132HFSI-SH

DS-8124HWSI-SH, DS-8132HWSI-SH

This manual may contain several technically incorrect places or printing errors, and the content is subject to change without notice. The updates will be added into the new version of this manual. We will readily improve or update the products or procedures described in the manual.

User Manual of DS-7200/7300/8100-SH Series DVR

Preventive and Cautionary Tips

Before connecting and operating your device, please be advised of the following tips:

• Ensure unit is installed in a well-ventilated, dust-free environment.

• Unit is designed for indoor use only.

• Keep all liquids away from the device.

• Ensure environmental conditions meet factory specifications.

• Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it

may cause damage to the sensitive electronics within the unit.

• Use the device in conjunction with an UPS if possible.

• Power down the unit before connecting and disconnecting accessories and peripherals.

• A factory recommended HDD should be used for this device.

• Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or

equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.

User Manual of DS-7200/7300/8100-SH Series DVR

Product Key Features

General

 Connectable to the network cameras and network domes (this feature is supported by HDVR

series).

 PAL/NTSC adaptive video inputs.  H.264 video compression with high reliability and superior definition.  Encoding at up to WD1 (PAL: 960×576, NTSC: 960×480) resolution for DS-7200HWI-SH,

DS-7204HWI-SV, DS-7200HVI-SV, DS-7200HWI-SL, DS-7224/7232HVI-SH, DS-7300HWI-SH, DS-7300HI-SH, DS-8100HCI-SH and DS-8100HWSI-SH models; and up to 4CIF resolution for DS-7204/7208/7216HVI-SH, DS-7200HFI-SH, DS-7300HFI-SH, and DS-8100HFSI-SH models.

 Each channel supports dual-stream.  Independent configuration for each channel, including resolution, frame rate, bit rate, image

quality, etc.

 Input and output video quality is configurable.  Normal and event recording parameters configurable per individual camera.  Encoding for audio/video composite stream or video stream; audio and video synchronization

during composite stream encoding.

 Watermark technology.  Video quality diagnostics.

Local Monitoring

 Simultaneous HDMI/VGA and CVBS outputs.  HDMI/VGA output at up to 1920×1080P resolution.  1/4/6/8/9/16/25/36-division live view is supported, and the display sequence of screens is

adjustable.

 Live view screen can be switched in group, and manual switch and automatic cycle view is also

provided, the interval of automatic cycle can be adjusted.

 Quick setting menu is provided for live view.  The selected live view channel can be shielded.  Motion detection, tamper-proof, video exception and video loss alarm functions.  Privacy mask.  Multiple PTZ protocols supported; setting and calling of PTZ preset, patrol and pattern.  Zooming in by clicking the mouse and PTZ tracing by dragging mouse.

HDD Management

 1 SATA hard disk can be connected to DS-7200HVI-SH, DS-7200HVI-SV, DS-7204HFI-SH,

DS-7204HWI-SV and DS-7204HWI-SH, DS-7200HWI-SL models, 2 SATA hard disks to DS-7208/7216HFI-SH, DS-7208/7216HWI-SH, DS-7224/7232HVI-SH and DS-7224/7232HWI-SH models, up to 4 SATA hard disks to DS-7300-SH, and up to 8 SATA hard disks to DS-8100-SH; with a maximum of 4TB storage capacity for each disk.

 8 network disks (8 NAS disks, or 7 NAS disks+1 IP SAN disk) can be connected.  HDD group management.  Support HDD standby function.  HDD property: redundancy, read-only, read/write (R/W).  HDD quota management; different capacity can be assigned to different channel.

User Manual of DS-7200/7300/8100-SH Series DVR

Recording and Playback

 Holiday recording schedule configuration.  Normal and event video encoding parameters.  Multiple recording types: manual, normal, motion, alarm, motion/alarm and motion & alarm.

Note: The alarm, motion/alarm and motion & alarm recording types are provided for

DS-7224/7232-SH, DS-7300-SH, DS-8100-SH and HDVR models only.

 Recording by main stream or sub stream is configurable.  8 recording time periods with separated recording types.  Pre-record and post-record for motion detection for recording, and pre-record time for schedule

and manual recording.

 Searching record files by event.  Customization of tags, searching and playing back by tags.  Locking and unlocking record files.  Local redundant recording.  Searching and playing back record files by channel number, recording type, start time, end time,

etc.

 Smart search for the selected area in the video.  Smart playback to go through less effective information.  Zooming in when playback.  Playing reversely.  Support pause, speed up, speed down, skip forward, and skip backward when playback, locating

by dragging the mouse.

 4/8/16-ch synchronous playback.

Backup

 Export video data by USB, SATA or eSATA storage device.

Note: The eSATA is supported by DS-7300-SH and DS-8100-SH models only.

 Export video clips when playback.  Management and maintenance of backup devices.

Alarm and Exception

 Configurable arming time of alarm input/output (for DS-7224/7232-SH, DS-7300-SH and

DS-8100-SH models).

 Alarm for video loss, motion detection, tampering, abnormal signal, video input/output standard

mismatch, illegal login, network disconnected, IP confliction, abnormal record, HDD error, and HDD full, etc.

 Alarm event triggers full screen monitoring, audio alarm, notifying surveillance center and

sending email.

 Automatic restore when system is abnormal.  Support alarm push notification (in live video or playback) on the linked mobile phones when

alarm event occurs.

Note: The mobile phone must be installed with the iVMS-4500 client software and the alarm

push function is enabled.

Other Local Functions

 Operable by mouse, IR remote control or front panel (for DS-7300-SH and DS-8100-SH).  Three-level user management; admin user is allowed to create many operating accounts and

define their operating permission, which includes the limit to access any channel.

 Operation, exceptions and log recording and searching.  Import and export of device configuration information.

User Manual of DS-7200/7300/8100-SH Series DVR

Network Functions

 1 self-adaptive 10M/100M network interface for DS-7204/7208/7216-SH/SV/SL, and 1

self-adaptive 10M/100M/1000M network interface for DS-7224/7232-SH, and DS-7300-SH, and 2 self-adaptive 10M/100M/1000M network interfaces for DS-8100-SH models.

 IPv6 is supported.  TCP/IP protocol, PPPoE, DHCP, DNS, DDNS, RTSP, NTP, SADP, SMTP, SNMP, NFS and

iSCSI are supported.

 TCP, UDP and RTP for unicast.  Auto/Manual port mapping and automatically discovered by NAT.  Remote search, playback, download, locking and unlocking of the record files, and downloading

files broken transfer resume.

 Remote parameters setup; remote import/export of device parameters.  Remote viewing of the device status, system logs and alarm status.  Remote locking and unlocking of control panel and mouse.  Remote HDD formatting and program upgrading.  Remote system restart.  RS-232 and RS-485 transparent channel transmission.

Note: RS-232 serial port is provided for DS-7300-SH and DS-8100-SH models only.

 Alarm event and exception information can be sent to the remote host.  Remotely start/stop recording.  Upgrade by remote FTP server.  Remote PTZ control.  Two-way audio and voice broadcasting.  Embedded WEB server.

Development Scalability:

 SDK for Windows and Linux system.  Source code of application software for demo.  Development support and training for application system.

User Manual of DS-7200/7300/8100-SH Series DVR

TABLE OF CONTENTS

Product Key Features ......................................................................................................... 5

C H A P T E R 1 ...................................................................................................................... 12

Introduction ............................................................................................................................. 12

1.1 Front Panel ................................................................................................................. 13

1.2 IR Remote Control Operations ................................................................................... 18

1.3 USB Mouse Operation ............................................................................................... 20

1.4 Input Method Description .......................................................................................... 20

1.5 Rear Panel .................................................................................................................. 21

1.6 Starting Up and Shutting Down the Device ............................................................... 26

C H A P T E R 2 ...................................................................................................................... 27

Getting Started ....................................................................................................................... 27

2.1 Using the Wizard for Basic Configuration ................................................................. 28

2.2 Adding and Connecting the IP Cameras ..................................................................... 33

2.2.1 Adding the IP Cameras ................................................................................... 33

2.2.2 Configuring the Connected IP Cameras .......................................................... 37

C H A P T E R 3 ...................................................................................................................... 38

Live View................................................................................................................................. 38

3.1 Introduction of Live View .......................................................................................... 39

3.2 Operations in Live View Mode .................................................................................. 40

3.2.1 Front Panel Operation ..................................................................................... 40

3.2.2 Using the Mouse in Live View ....................................................................... 40

3.2.3 Using an Auxiliary Monitor ............................................................................ 41

3.2.4 Main/Aux Output Switching ........................................................................... 42

3.2.5 Quick Setting Toolbar in Live View Mode ..................................................... 42

3.3 Configuring Live View Settings ................................................................................. 45

3.4 Channel-zero Encoding .............................................................................................. 47

3.5 Manual Video Quality Diagnostics ............................................................................ 47

3.6 User Logout................................................................................................................ 49

C H A P T E R 4 ...................................................................................................................... 50

PTZ Controls .......................................................................................................................... 50

4.1 Configuring PTZ Settings .......................................................................................... 51

4.2 Setting PTZ Presets, Patrols & Patterns ..................................................................... 51

4.2.1 Customizing Presets ........................................................................................ 51

4.2.2 Calling Presets ................................................................................................. 52

4.2.3 Customizing Patrols ........................................................................................ 53

4.2.4 Calling Patrols ................................................................................................. 55

4.2.5 Customizing Patterns ...................................................................................... 56

4.2.6 Calling Patterns ............................................................................................... 57

4.3 PTZ Control Toolbar .................................................................................................. 58

C H A P T E R 5 ...................................................................................................................... 59

Record Settings ....................................................................................................................... 59

User Manual of DS-7200/7300/8100-SH Series DVR

5.1 Configuring Encoding Parameters ............................................................................. 60

5.2 Configuring Record Schedule .................................................................................... 63

5.3 Configuring Motion Detection Record ...................................................................... 67

5.4 Configuring Alarm Triggered Record ........................................................................ 71

5.5 Configuring Manual Record ...................................................................................... 74

5.6 Configuring Holiday Record ...................................................................................... 75

5.7 Configuring Redundant Record ................................................................................. 77

5.8 Configuring HDD Group for Record ......................................................................... 79

5.9 Files Protection .......................................................................................................... 81

C H A P T E R 6 ...................................................................................................................... 84

Playback .................................................................................................................................. 84

6.1 Playing Back Record Files ......................................................................................... 85

6.1.1 Playing Back by Channel ................................................................................ 85

6.1.2 Playing Back by Time ..................................................................................... 87

6.1.3 Playing Back by Event Search ........................................................................ 89

6.1.4 Playing Back by Tag ....................................................................................... 92

6.1.5 Playing Back by Smart Search ........................................................................ 95

6.1.6 Playing Back by System Log .......................................................................... 96

6.1.7 Playing Back External Files ............................................................................ 97

6.2 Auxiliary Functions of Playback ................................................................................ 99

6.2.1 Playing Back Frame by Frame ........................................................................ 99

6.2.2 Smart Search ................................................................................................... 99

6.2.3 Digital Zoom ................................................................................................. 101

6.2.4 Reverse Playback of Multi-channel .............................................................. 102

C H A P T E R 7 .................................................................................................................... 103

Backup .................................................................................................................................. 103

7.1 Backing up Record Files .......................................................................................... 104

7.1.1 Quick Export ................................................................................................. 104

7.1.2 Backing up by Normal Video Search ............................................................ 105

7.1.3 Backing up by Event Search ......................................................................... 108

7.1.4 Backing up Video Clips ................................................................................ 111

7.2 Managing Backup Devices ...................................................................................... 114

C H A P T E R 8 .................................................................................................................... 116

Alarm Settings ...................................................................................................................... 116

8.1 Setting Motion Detection ......................................................................................... 117

8.2 Setting Sensor Alarms .............................................................................................. 120

8.3 Detecting Video Loss ............................................................................................... 123

8.4 Detecting Video Tampering...................................................................................... 124

8.5 Handling Exceptions ................................................................................................ 125

8.6 Setting Alarm Response Actions .............................................................................. 126

8.7 Triggering or Clearing Alarm Output Manually....................................................... 128

C H A P T E R 9 .................................................................................................................... 129

Network Settings .................................................................................................................. 129

9.1 Configuring General Settings ................................................................................... 130

User Manual of DS-7200/7300/8100-SH Series DVR

9.2 Configuring Advanced Settings ............................................................................... 132

9.2.1 Configuring PPPoE Settings ......................................................................... 132

9.2.2 Configuring DDNS ....................................................................................... 133

9.2.3 Configuring NTP Server ............................................................................... 136

9.2.4 Configuring SNMP ....................................................................................... 136

9.2.5 Configuring NAT .......................................................................................... 137

9.2.6 Configuring Remote Alarm Host .................................................................. 140

9.2.7 Configuring Multicast ................................................................................... 141

9.2.8 Configuring RTSP ......................................................................................... 141

9.2.9 Configuring Server and HTTP Ports ............................................................. 142

9.2.10 Configuring HTTPS Settings ...................................................................... 142

9.2.11 Configuring Email ....................................................................................... 144

9.3 Checking Network Traffic ........................................................................................ 146

9.4 Network Detection ................................................................................................... 147

9.4.1 Testing Network Delay and Packet Loss ...................................................... 147

9.4.2 Exporting Network Packet ............................................................................ 147

9.4.3 Checking Network Status .............................................................................. 148

9.4.4 Checking Network Statistics ......................................................................... 150

C H A P T E R 1 0 ................................................................................................................. 151

HDD Management ............................................................................................................... 151

10.1 Initializing HDDs ................................................................................................... 152

10.2 Managing Network HDD ....................................................................................... 154

10.3 Managing HDD Group ........................................................................................... 157

10.3.1 Setting HDD Groups ................................................................................... 157

10.3.2 Setting HDD Property ................................................................................. 158

10.4 Configuring Quota Mode ....................................................................................... 160

10.5 Checking HDD Status ............................................................................................ 161

10.6 Checking S.M.A.R.T. Information ......................................................................... 162

10.7 Detecting Bad Sector.............................................................................................. 163

10.8 Configuring HDD Error Alarms ............................................................................. 164

C H A P T E R 11 .................................................................................................................. 165

Camera Settings ................................................................................................................... 165

11.1 Configuring OSD Settings ..................................................................................... 166

11.2 Configuring Privacy Mask ..................................................................................... 167

11.3 Configuring Video Parameters ............................................................................... 168

11.4 Configuring Video Quality Diagnostics ................................................................. 169

C H A P T E R 1 2 ................................................................................................................. 171

Device Management and Maintenance .............................................................................. 171

12.1 Viewing System Information ................................................................................. 172

12.1.1 Viewing Device Information ....................................................................... 172

12.1.2 Viewing Camera Information...................................................................... 172

12.1.3 Viewing Record Information ...................................................................... 172

12.1.4 Viewing Alarm Information ........................................................................ 173

12.1.5 Viewing Network Information .................................................................... 174

User Manual of DS-7200/7300/8100-SH Series DVR

12.1.6 Viewing HDD Information ......................................................................... 174

12.2 Searching & Exporting Log Files .......................................................................... 176

12.3 Importing/Exporting Configuration Files ............................................................... 178

12.4 Upgrading System .................................................................................................. 180

12.4.1 Upgrading by Local Backup Device ........................................................... 180

12.4.2 Upgrading by FTP ....................................................................................... 180

12.5 Restoring Default Settings ..................................................................................... 182

C H A P T E R 1 3 ................................................................................................................. 183

Others .................................................................................................................................... 183

13.1 Configuring General Settings ................................................................................. 184

13.2 Configuring RS-232 Serial Port ............................................................................. 185

13.3 Configuring DST Settings ...................................................................................... 186

13.4 Configuring More Settings ..................................................................................... 187

13.5 Managing User Accounts ....................................................................................... 188

13.5.1 Adding a User ............................................................................................. 188

13.5.2 Deleting a User ............................................................................................ 190

13.5.3 Editing a User .............................................................................................. 191

13.5.4 Changing Password of Admin..................................................................... 192

C H A P T E R 1 4 .......................................................................................................... 194

Appendix ............................................................................................................................... 194

List of Compatible Hikvision IP Cameras ..................................................................... 195

Glossary ......................................................................................................................... 196

FAQ ................................................................................................................................ 197

User Manual of DS-7200/7300/8100-SH Series DVR

C H A P T E R 1

Introduction

User Manual of DS-7200/7300/8100-SH Series DVR

1.1 Front Panel

DS-7200-SH and DS-7200HVI-SV:

The front panel of DS-7200-SH/SV series DVR is shown in Figure 1.1:

Figure 1.1 Front Panel of DS-7200-SH/SV

Table 1.1 Description of Control Panel Buttons

No.

Name

Function Description

POWER

POWER indicator turns green when DVR is powered up.

STATUS

STATUS indicator lights in red when HDD is reading/writing.

Tx/Rx

Tx/Rx indictor blinks green when network connection is functioning properly.

USB Interface

Connects USB mouse or USB flash memory devices.

IR Receiver

Receiver for IR remote.

DS-7300-SH:

The front panel of DS-7300-SH is shown below:

Figure 1.2 Front Panel of DS-7300-SH

Table 1.2 Description of Control Panel Buttons

No.

Name

Function Description

POWER ON/OFF

Power on/off switch.

IR Receiver

Receiver for IR remote control.

USB

Connect to USB mouse or USB flash memory devices.

DVD-R/W

Slot for DVD-R/W.

5 POWER

Power indicator lights in green when DVR is powered up.

READY

Ready indicator is normally green, indicating that the DVR is functioning properly.

User Manual of DS-7200/7300/8100-SH Series DVR

No.

Name

Function Description

STATUS

Indicator turns green when DVR is controlled by an IR remote control with the address from 1~254; Indicator turns red when the SHIFT button is used; Indicator does not light when the DVR is controlled by a keyboard or by the IR remote control with the address of 255; Indicator turns green when the DVR is controlled by IR remote control (with the address from 1~254) and keyboard at the same time , and the SHIFT button is not used; Indicator turns orange : (a) when the DVR is controlled by IR remote control (with the address from 1~254) and keyboard at the same time and the SHIFT button is used as well; (b) when the DVR is controlled by IR remote control (with the address from 1~254) and the SHIFT button is used.

ALARM

Alarm indicator turns red when a sensor alarm is detected.

HDD

HDD indicator blinks in red when data is being read from or written to HDD.

Tx/Rx

TX/RX indictor blinks in green when network connection is functioning properly.

1/MENU

Enter numeral “1”; Access the main menu interface.

2ABC/F1

Enter numeral “2”; Enter letters “ABC”;

The F1 button can be used to select all items on the list; In PTZ Control mode, the F1 button can be used to zoom out (zoom-) the PTZ camera; In live view or playback mode, the F1 button can be used to switch between main and spot video output.

3DEF/F2

Enter numeral “3”; Enter letters “DEF”;

In PTZ Control mode, the F1 button can be used to zoom in (zoom+) the PTZ camera; The F2 button can be used to cycle through tab pages.

4GHI/ESC

Enter numeral “4”; Enter letters “GHI”;

Exit and back to the previous menu.

5JKL/EDIT

Enter numeral “5”; Enter letters “JKL”;

Delete characters before cursor; Select the checkbox and ON/OFF switch; Start/stop record clipping in playback.

SHIFT

Switch of compound keys between the numeric/letter input and functional control.

6MNO/PLAY

Enter numeral “6”; Enter letters “MNO”;

In Playback mode, it is used for direct access to playback interface.

7PQRS/REC

Enter numeral “7”; Enter letters “PQRS”; Manual record, for direct access to manual record interface; manually enable/disable record.

8TUV/PTZ

Enter numeral “8”; Enter letters “TUV”;

Access PTZ control interface.

User Manual of DS-7200/7300/8100-SH Series DVR

No.

Name

Function Description

9WXYZ/PREV

Enter numeral “9”; Enter letters “WXYZ”;

Multi-camera display in live view; In Playback mode or MenuPlaybackTag playback interface, this button can be used to delete the selected tag.

0/A

Enter numeral “0”; Switch between input methods (upper and lowercase alphabet, symbols and numeric input). In Playback mode, this button can be used to add the default tag.

DIRECTION

The DIRECTION buttons are used to navigate between different fields and items in menus. In Playback mode, the Up and Down button is used to speed up and slow down recorded video. In All-day Playback mode, the Left/Right button can be used to select the recorded video of next/previous day; in Playback by Normal Video Search, the Left/Right button can be used to select the next/previous recorded file. In Live View mode, the directional buttons can be used to cycle through channels. In PTZ control mode, it can control the movement of the PTZ camera.

ENTER

Confirm selection in any of the menu modes. It can also be used to tick checkbox fields. In Playback mode, it can be used to play or pause the video. In Single-frame Playback mode, pressing the ENTER button will advance the video by a single frame. In Auto-switch mode, it can be used to stop /start auto switch.

JOG SHUTTLE Control

Move the active selection in a menu. The inner ring will move the selection up and down; the outer ring will move it left and right. In Playback mode, the inner ring is used to jump 30s forward/backward in video files. The outer ring can be used to speed up/slow down the video. In Live View mode, it can be used to cycle through different channels. In PTZ control mode, in can control the movement of the PTZ camera.

DS-8100-SH:

The front panel of DS-8100-SH is shown below:

Figure 1.3 Front Panel of DS-8100-SH

User Manual of DS-7200/7300/8100-SH Series DVR

Table 1.3 Description of Control Panel Buttons

No.

Name

Function Description

POWER ON/OFF

Power on/off switch.

IR Receiver

Receiver for IR remote control.

USB

Connect to USB mouse or USB flash memory devices.

DVD-R/W

Slot for DVD-R/W.

ALARM

Alarm indicator turns red when a sensor alarm is detected.

READY

Ready indicator is normally blue, indicating that the DVR is functioning properly.

STATUS

Indicator turns blue when DVR is controlled by an IR remote. Indicator turns red when controlled by a keyboard and orange when IR remote and keyboard is used at the same time. Indicator does not light when the DVR is controlled by the IR remote control with the address of 255.

HDD

HDD indicator blinks in red when data is being read from or written to HDD.

Tx/Rx

Tx/Rx indictor blinks in blue when network connection is functioning properly.

GUARD

Indicator turns blue when the device is armed; Indicator does not light when the device is disarmed; The arm/disarm state can be initiated by pressing and holding on the ESC button for more than 3 seconds in live view mode.

Channel Status LED Indicators

The button lights in blue when the corresponding channel is recording; it is red when the channel is in network transmission status; it is pink when the channel is recording and transmitting.

Alphanumeric Buttons

Switch to the corresponding channel in Live View or PTZ Control mode. Input numbers and characters in Edit mode. Switch between different channels in All-day Playback mode.

ESC

Exit and back to the previous menu. Arm/disarm the DVR in live view mode.

REC/SHOT

Enter the Manual Record interface. Turn audio on/off in Playback mode; In PTZ control mode, pressing the REC/SHOT button and a Numeric button will call a PTZ preset.

PLAY/AUTO

Enter the Playback menu; Auto scan in the PTZ Control mode.

ZOOM+ Button

In PTZ control mode, the ZOOM+ button is used to zoom in the PTZ camera.

A/FOCUS+

Adjust focus in the PTZ Control mode. Switch between input methods (upper and lowercase alphabet, symbols and numeric input).

EDIT/IRIS+

Edit text fields. When editing text fields, it will also function as a Backspace button to delete the character in front of the cursor. On checkbox fields, pressing the button will tick the checkbox. In PTZ Control mode, the button adjusts the iris of the camera.

In Playback mode, it can be used to generate video clips for backup.

MENU/WIPER

Return to the Main menu (after successful login); Turn off audible key beeper by pressing and holding the button for 5 seconds; Start wiper (if applicable) in PTZ Control mode.

F1/LIGHT

The F1/LIGHT button when used in a list field will select all items on the list. In PTZ Control mode, it will turn on/off PTZ light.

F2/AUX

The F2/AUX button is used to cycle through tab pages.

MAIN/SPOT/ZO OM-

Switch to the control of spot output; In PTZ Control mode, it can be used to zoom out the PTZ camera.

PREV/FOCUS-

Switch between single screen and multi-screen mode. In PTZ Control mode, it is used to adjust the focus in conjunction with the A/FOCUS+ button.

PTZ/IRIS-

Enter the PTZ Control mode. In PTZ Control mode, it is used to close the iris of the PTZ camera.

DIRECTION

The DIRECTION buttons are used to navigate between different fields and items

User Manual of DS-7200/7300/8100-SH Series DVR

No.

Name

Function Description

in menus. In Playback mode, the Up and Down button is used to speed up and slow down recorded video. In All-day Playback mode, the Left/Right button can be used to select the recorded video of next/previous day; in Playback by Normal Video Search, the Left/Right button can be used to select the next/previous recorded file. In Live View mode, the directional buttons can be used to cycle through channels. In PTZ control mode, it can control the movement of the PTZ camera.

ENTER

JOG SHUTTLE Control

User Manual of DS-7200/7300/8100-SH Series DVR

1.2 IR Remote Control Operations

The device may also be controlled with the included IR remote control, shown in Figure 1.4.

Note: Batteries (2×AAA) must be installed before operation.

Figure 1.4 Remote Control

Table 1.4 Description of the IR Remote Control Buttons

No.

Name

Description

POWER

Power on/off the device.

DEV

Enables/Disables Remote Control.

Alphanumeric Buttons

Switching to the corresponding channel in Live view or PTZ Control mode. Inputting numbers and characters in Edit mode. Switching between different channels in All-day Playback mode.

EDIT Button

Editing text fields. When editing text fields, it will also function as a Backspace button to delete the character in front of the cursor. On checkbox fields, pressing the EDIT button will tick the checkbox. In Playback mode, it can be used to generate video clips for backup.

A Button

Switching between input methods (upper and lowercase alphabet, symbols and numeric input).

REC Button

Entering the Manual Record settings menu. In PTZ control settings, press the REC button and then you can call a

PTZ preset by pressing Numeric button.

User Manual of DS-7200/7300/8100-SH Series DVR

No.

Name

Description

PLAY Button

Entering the All-day Playback menu.

INFO Button

Reserved.

VOIP/MON Button

Selecting all items on the list; In live view or playback mode, it can be used to switch between main

and auxiliary video output.

MENU Button

Back to the Main menu (after successful login).

PREV Button

Switching between single screen and multi-screen mode.

DIRECTION/ENTER Buttons

Navigating between different fields and items in menus. In Playback mode, the Up and Down button are used to speed up and slow down the playing of recorded video. The Left and Right button will select the recorded video of 30 reverse and 30s forward. In live view mode, these buttons can be used to cycle through channels.

PTZ Button

Enter the PTZ Control mode.

ESC Button

Back to the previous menu Pressing for arming/disarming the DVR in Live View mode.

RESERVED

Reserved.

F1 Button

Selecting all items on the list when used in a list field. In PTZ Control mode, it will turn on/off PTZ light.

PTZ Control Buttons

Adjusting the iris, focus and zoom of a PTZ camera.

F2 Button

Cycle through tab pages.

Troubleshooting Remote Control:

Note: Make sure you have installed batteries properly in the remote control. And you have to aim the remote

control at the IR receiver on the front panel.

If there is no response after you press any button on the remote, follow the procedure below to troubleshoot.

Steps:

1. Go to Menu > Configuration > General > More Settings by operating the mouse.

2. Check and remember the device No. The default No. is 255. This device No. is valid for all the IR

remote controls.

3. Press the DEV button on the remote control.

4. Enter the device No. from step 2.

5. Press the ENTER button on the remote.

If the remote control is operating properly, but there is still no response from the remote, please check the following:

1. Batteries are installed correctly and the polarities of the batteries are not reversed.

2. Batteries are fresh and not out of charge.

3. IR receiver is not obstructed.

If the remote still can’t function properly, please change a remote and try again, or contact the device provider.

User Manual of DS-7200/7300/8100-SH Series DVR

1.3 USB Mouse Operation

A regular 3-button (Left/Right/Scroll-wheel) USB mouse can also be used with this device. To use a USB mouse:

1. Plug USB mouse into one of the USB interfaces on the front panel of the device.

2. The mouse should automatically be detected. If in a rare case that the mouse is not detected, the possible

reason may be that the two devices are not compatible, please refer to the recommended device list from your provider.

The operation of the mouse:

Table 1.5 Description of the Mouse Control

Name

Action

Description

Left-Click

Single-Click

Live view: Select channel and show the quick set menu. Menu: Select and enter.

Double-Click

Live view: Switch single-screen and multi-screen.

Click and Drag

PTZ control: pan, tilt and zoom. Tamper-proof, privacy mask and motion detection: Select target area. Digital zoom-in: Drag and select target area. Live view: Drag channel/time bar.

Right-Click

Single-Click

Live view: Show menu. Menu: Exit current menu to upper level menu.

Scroll-Wheel

Scrolling up

Live view: Previous screen. Right-click Menu: Previous item.

Scrolling down

Live view: Next screen. Right-click Menu: Next item.

1.4 Input Method Description

Figure 1.5 Soft Keyboard

Description of the buttons on the soft keyboard:

Table 1.6 Description of the Soft Keyboard Icons

Icons

Description

Icons

Description

English

Capital English

Numbers

Symbols

Lowercase/Uppercase

Backspace

Space

Enter

Exit

User Manual of DS-7200/7300/8100-SH Series DVR

1.5 Rear Panel

DS-7204HVI/HFI/HWI-SH, DS-7204HVI-SV and DS-7204HWI-SV:

The rear panel of 7204HVI/HFI/HWI-SH, DS-7204HVI-SV and DS-7204HWI-SV DVR is shown in Figure

1.6.

Figure 1.6 Rear Panel of DS-7204HVI/HFI/HWI-SH, DS-7204HVI-SV and DS-7204HWI-SV

DS-7216HVI-SH, DS-7216HVI-SV and DS-7216HWI-SL:

The rear panel of DS-7216HVI-SH, DS-7216HVI-SV and DS-7216WI-SL DVR is shown in Figure 1.7.

Figure 1.7 Rear Panel of DS-7216HVI-SH and DS-7216HVI-SV

Note: The rear panel of DS-7208HVI-SH/DS-7208HVI-SV/DS-7208HWI-SL provides 8 video input

interfaces.

DS-7216HFI-SH and DS-7216HWI-SH:

The rear panel of DS-7216HFI-SH and DS-7216HWI-SH is shown in Figure 1.8.

Figure 1.8 Rear Panel of DS-7216HFI-SH and DS-7216HWI-SH

Note: The rear panel of DS-7208HFI-SH/DS-7208HWI-SH provides 8 video input interfaces.

User Manual of DS-7200/7300/8100-SH Series DVR

Table 1.7 Description of Rear Panel

No.

Item

Description

VIDEO IN

BNC connector for analog video input.

VIDEO OUT

BNC connector for video output.

USB Interface

Connects USB mouse or USB flash memory devices.

HDMI

HDMI video output.

VGA

DB15 connector for VGA output. Display local video output and menu.

AUDIO IN

RCA connector for audio input.

AUDIO OUT

RCA connector for audio output.

LAN Interface

RJ45 10M/100M Ethernet interface.

RS-485 Interface

Connector for RS-485 devices. Connect the D+ and D- terminals to T+ and T- of PTZ receiver respectively.

12V

12VDC power supply.

POWER

Switch for turning on/off the device.

GND

Ground (needs to be connected when DVR starts up).

DS-7224/7232HVI-SH and DS-7224/7232HWI-SH:

The rear panel of DS-7232HVI-SH/DS-7232HWI-SH is shown in Figure 1.9.

3 4 56789 10 11

Figure 1.9 Rear Panel of DS-7232HVI-SH and DS-7232HWI-SH

Note: The rear panel of DS-7224HVI-SH/DS-7224HWI-SH provides 24 video input interfaces.

Table 1.8 Description of Rear Panel

No.

Item

Description

VIDEO IN

BNC connector for analog video input.

VIDEO OUT

BNC connector for video output.

USB Interface

Connects USB mouse or USB flash memory devices.

HDMI

HDMI video output.

VGA

DB15 connector for VGA output. Display local video output and menu.

AUDIO IN

RCA connector for audio input.

AUDIO OUT

RCA connector for audio output.

Alarm In/Out

Connector for alarm input/output.

LAN Interface

RJ45 10M / 100M / 1000M Ethernet interface.

RS-485 Interface

Connector for RS-485 devices. Connect the D+ and D- terminals to R+ and Rterminals of PTZ receiver respectively.

12V

12VDC power supply.

POWER

Switch for turning on/off the device.

GND

Ground(needs to be connected when DVR starts up)

DS-7316HFI-SH and DS-7316HWI-SH:

The rear panel of DS-7316HFI-SH and DS-7316HWI-SH DVR is shown in Figure 1.10.

User Manual of DS-7200/7300/8100-SH Series DVR

Figure 1.10 Rear Panel of DS-7316HFI-SH and DS-7316HWI-SH

Note: The rear panel of DS-7304HFI-SH/DS-7304HWI-SH provides 4 video input interfaces, and the rear

panel of DS-7308HFI-SH/DS-7308HWI-SH provides 8 video input interfaces.

Table 1.9 Description of Rear Panel

No.

Item

Description

VIDEO IN

BNC connector for analog video input.

2 MAIN VIDEO OUT

BNC connector for video output.

SPOT VIDEO OUT

BNC connector for spot video output.

HDMI

HDMI video output.

USB Interface

Connects USB mouse or USB flash memory devices.

RS-232

Connector for RS-232 devices.

VGA

DB15 connector for VGA output. Display local video output and menu.

AUDIO IN

RCA connector for audio input.

AUDIO OUT

RCA connector for audio output.

LAN Interface

RJ45 10M/100M/1000M Ethernet interface.

RS-485 Interface

Connector for RS-485 devices. Connect the D+ and D- terminals to R+ and R- terminals of PTZ receiver respectively.

Alarm In/Out

Connector for alarm input/output.

eSATA

Connects external SATA HDD, DVD-R/W.

100~240VAC

100~240VAC power supply.

POWER

Switch for turning on/off the device.

GND

Ground (needs to be connected when DVR starts up)

DS-7332HFI-SH, DS-7332HWI-SH and DS-7332HI-SH:

The rear panel of DS-7332HFI-SH, DS-7332HWI-SH and DS-7332HI-SH DVR is shown in Figure 1.11.

Figure 1.11 Rear Panel of DS-7332HFI-SH, DS-7332HWI-SH and DS-7332HI-SH

Note: DS-7324HFI-SH, DS-7324HWI-SH and DS-7324HI-SH models provide 24 video input interfaces on

the rear panel.

User Manual of DS-7200/7300/8100-SH Series DVR

Table 1.10 Description of Rear Panel

No.

Item

Description

1 MAIN VIDEO OUT

BNC connector for video output.

SPOT VIDEO OUT

BNC connector for spot video output.

VIDEO IN

BNC connector for analog video input.

3 CVBS AUDIO OUT

RCA connector for audio output. This connector is synchronized with CVBS video output.

VGA AUDIO OUT

RCA connector for audio output. This connector is synchronized with VGA video output.

LINE IN

RCA connector for two-way audio input.

AUDIO IN

RCA connector for audio input.

VGA

DB15 connector for VGA output. Display local video output and menu.

HDMI

HDMI video output.

USB Interface

Connects USB mouse or USB flash memory devices.

LAN Interface

RJ45 10M/100M/1000M Ethernet interface.

RS-232

Connector for RS-232 devices.

11 Termination Switch

RS-485 termination switch. Up position is not terminated. Down is terminated with 120Ω resistance.

12 RS-485 Interface

Connector for RS-485 devices. Connect the T+ and T- terminals to the R+ and R- terminals of PTZ receiver respectively.

Connect the D+ and D- terminals to Ta and Tb terminals of the controller. For cascading devices, the first DVR’s D+ and D- terminals should be connected with the D+ and D- terminals of the next DVR.

Alarm In/Out

Connector for alarm input/output.

eSATA

Connects external SATA HDD, DVD-R/W.

GND

Ground(needs to be connected when DVR starts up)

100~240VAC

100~240VAC power supply.

POWER

Switch for turning on/off the device.

DS-8100-SH:

The rear panel of DS-8100-SH DVR is shown in Figure 1.12.

Figure 1.12 Rear Panel of DS-8132HCI-SH, DS-8132HFSI-SH and DS-8132HWSI-SH

Note: DS-8124HCI-SH, DS-8124HFSI-SH and DS-8124HWSI-SH models provide 24 video input interfaces

on the rear panel.

User Manual of DS-7200/7300/8100-SH Series DVR

Table 1.11 Description of Rear Panel

No.

Item

Description

VIDEO IN

BNC connector for analog video input.

2 MAIN VIDEO OUT

BNC connector for video output.

SPOT VIDEO OUT

BNC connector for spot video output.

3 CVBS AUDIO OUT

RCA connector for audio output. This connector is synchronized with CVBS video output.

VGA AUDIO OUT

RCA connector for audio output. This connector is synchronized with VGA video output.

LINE IN

RCA connector for two-way audio input.

AUDIO IN (1-4)

RCA connector for audio input.

AUDIO IN (5-16)

DB26 connector for audio input.

VGA

DB15 connector for VGA output. Display local video output and menu.

RS-232

Connector for RS-232 devices.

HDMI

HDMI video output.

USB Interface

Connects USB mouse or USB flash memory devices.

LAN1/LAN2 Interface

2 RJ45 10M/100M/1000M Ethernet interfaces.

eSATA

Connects external SATA HDD, DVD-R/W.

13 Termination Switch

RS-485 termination switch. Up position is not terminated. Down is terminated with 120Ω resistance.

14 RS-485 Interface

Connector for RS-485 devices. Connect the T+ and T- terminals to the R+ and R- terminals of PTZ receiver respectively.

Alarm In/Out

Connector for alarm input/output.

GND

Ground(needs to be connected when DVR starts up)

100~240VAC

100~240VAC power supply.

POWER

Switch for turning on/off the device.

User Manual of DS-7200/7300/8100-SH Series DVR

1.6 Starting Up and Shutting Down the Device

Purpose:

Proper startup and shutdown procedures are crucial to expanding the life of the device.

Before you start:

Check that the voltage of the extra power supply is the same with the device’s requirement, and the ground connection is working properly.

Starting up the device:

Steps:

1. Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an

Uninterruptible Power Supply (UPS) be used in conjunction with the device.

2. Press the POWER button on the rear panel. The Power indicator LED should turn green indicating that

the unit begins to start up.

Shutting down the device:

Steps:

1. Enter the Shutdown menu.

Menu > Shutdown

Figure 1.13 Shutdown Menu

2. Click the Shutdown button to enter the following dialog box:

Figure 1.14 Dialog Box for Shutdown

3. Click the Yes button. The following message box pops up:

Figure 1.15 Message Box for Power Off

4. Turn off the power switch on the rear panel of DVR.

Rebooting the device In the Shutdown menu (Figure 1.13), you can also click Reboot to reboot the device.

User Manual of DS-7200/7300/8100-SH Series DVR

C H A P T E R 2

Getting Started

User Manual of DS-7200/7300/8100-SH Series DVR

2.1 Using the Wizard for Basic Configuration

The Setup Wizard can walk you through some important settings of the device. By default, the Setup Wizard starts once the device has loaded. Operating the Setup Wizard:

1. Select the system resolution from the drop-down menu. The default resolution is 1280×1024/60Hz. Click Apply to save the resolution settings.

Figure 2.1 Start Wizard Interface

Note: By default, the system resolution is set to 1280×1024.

2. Check the checkbox to enable Setup Wizard when device starts. Click Next to continue the setup

wizard. You can also click Cancel to exit the Setup Wizard, or use the Setup Wizard next time by leaving the “Start wizard when DVR starts?” checkbox checked and exit.

Figure 2.2 Start Wizard Interface

3. Click Next button on the Wizard window to enter the Login window, as shown in Figure 2.3.

1) Enter the admin password. By default, the password is 12345.

User Manual of DS-7200/7300/8100-SH Series DVR

2) To change the admin password, check the New Admin Password checkbox. Enter the new

password and confirm the password in the given fields.

Figure 2.3 Login Window

4. Click the Next button to enter the Date and Time settings window, as shown in Figure 2.4. Set the time zone, date format, system date and system time.

Figure 2.4 Date and Time Settings

5. Click Next button which takes you back to the Network Setup Wizard window, as shown in Figure 2.5. Set the network parameters, including the NIC type, IPv4 address, IPv4 subnet mask, default gateway, etc. You can enable the DHCP to automatically obtain an IP address and other network settings from that server.

+ 168 hidden pages

HIKVISION DS-7204HFI-SH, DS-7300-SH, DS-7208HFI-SH, DS-7216HFI-SH, DS-7204HWI-SH User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual