HIKVISION DS-8008HCI-S, DS-8000HCI-S, DS-8000HFI-S, DS-8004HFI-S, DS-8004HCI-S User Manual
...
User Manual of DS-8000-S Series Net DVR
Page 1 Total 121
DS-8000-S Series Net DVR
User Manual
(V2.0)
Thank you for purchasing our embedded Net DVR. This manual is applicable for
DS-8000HCI-S and DS-8000HFI-S series Net DVR. Please read this User Manual carefully to
ensure that you can use the device correctly and safely.
The contents of this Manual are subject to change without notice.
User Manual of DS-8000-S Series Net DVR
Page 2 Total 121
Index
Version Description ........................................................................................................................... 4
Chapter1 Product Introduction .................................................................................................. 6
1.1 Summary ................................................................................................................... 6
1.2 Model Description ..................................................................................................... 6
1.3 Features ..................................................................................................................... 6
Chapter2 Installation ................................................................................................................. 9
2.1 Checking the DVR and Its Accessories ..................................................................... 9
2.2 HDD Installation ....................................................................................................... 9
2.3 Rear Panel Description ............................................................................................ 10
2.3.1 4-ch DS-8004HFI-S Rear Panel ...................................................................... 10
2.3.2 4-ch DS-8004HCI-S Rear Panel ..................................................................... 11
2.3.3 8-ch/16-ch HCI-S/HFI-S Rear Panel ............................................................... 12
2.4 External Alarm In/Out Connection ......................................................................... 14
Chapter3 Operational Instructions .......................................................................................... 15
3.1 Front Panel .............................................................................................................. 15
3.2 IR Controller ........................................................................................................... 18
3.3 Menu Description .................................................................................................... 20
3.3.1 Menu Items ..................................................................................................... 20
3.3.2 Menu Operation .............................................................................................. 21
3.4 Character Input ........................................................................................................ 24
Chapter4 Basic Operation Guide ............................................................................................ 25
4.1 Power on ................................................................................................................. 25
4.2 Preview .................................................................................................................... 25
4.3 User name and password ......................................................................................... 28
4.4 PTZ Control ............................................................................................................ 30
4.5 Manual Record ........................................................................................................ 32
4.6 Playback .................................................................................................................. 33
4.7 Backup Recorded Files ........................................................................................... 38
4.8 Shut Down DVR ..................................................................................................... 40
Chapter5 Main and Aux Output Function ............................................................................... 42
5.1 Main and aux output ................................................................................................ 42
5.2 Main and Aux output preview ................................................................................. 43
5.3 Main and Aux output playback ............................................................................... 46
5.4 Main or Aux output to control PTZ ......................................................................... 47
Chapter6 Parameters Setup Guide .......................................................................................... 48
6.1 Administrator and Password ................................................................................... 48
6.2 Add and Delete User ............................................................................................... 50
6.3 Unit Name and Device ID ....................................................................................... 54
6.4 Video Output Standard and VGA Setup .................................................................. 55
6.5 OSD Setup ............................................................................................................... 56
6.6 Video Parameters Setup .......................................................................................... 60
User Manual of DS-8000-S Series Net DVR
Page 3 Total 121
6.7 Mask Area Setup ..................................................................................................... 61
6.8 View Tampering Alarm ........................................................................................... 63
6.9 Video Loss Alarm .................................................................................................... 65
6.10 Motion Detection Alarm ......................................................................................... 67
6.11 Preview Properties .................................................................................................. 70
6.12 Recording Setup ...................................................................................................... 73
6.13 External Alarm Input and Relay Output .................................................................. 77
6.14 Network Parameters ................................................................................................ 81
6.15 PTZ ......................................................................................................................... 83
6.16 RS232 setup ............................................................................................................ 87
6.17 Exceptions ............................................................................................................... 92
6.18 Transaction Information .......................................................................................... 93
Chapter7 Utilities .................................................................................................................... 97
7.1 Save Parameters ...................................................................................................... 97
7.2 Restore Parameters .................................................................................................. 97
7.3 Upgrade ................................................................................................................... 98
7.4 Hard Disk Management .......................................................................................... 99
7.5 Clear Alarm Out ...................................................................................................... 99
7.6 Reboot ..................................................................................................................... 99
7.7 Power Off ................................................................................................................ 99
7.8 View Log ................................................................................................................. 99
7.9 System Information ............................................................................................... 102
Chapter8 Firmware Upgrade ................................................................................................ 103
8.1 FTP Server Setup .................................................................................................. 103
8.2 Upgrade Mode ....................................................................................................... 106
Appendix A HDD Capacity Calculation ................................................................................... 107
Appendix B DVR Connect Cable Definition ............................................................................ 108
1 RS-485 connect cable made method ............................................................................. 108
2 UTP network connect cable made method .................................................................... 108
3 RS-232 connect cable made method ............................................................................. 109
Appendix C Specifications ........................................................................................................ 112
Appendix D Quick Search Function Table ................................................................................ 115
Appendix E Troubleshooting .................................................................................................... 117
Appendix F Product Service ..................................................................................................... 119
Appendix G Customer Information Card .................................................................................. 120
User Manual of DS-8000-S Series Net DVR
Page 4 Total 121
Version Description
Version2.0 built 070206:
The new version firmware DVR has the following new features:
1. Support USB mouse
Recommended USB mouse model list:
Logitech: M-UV83
Benq: M800
ViewSonic: MC204
Philips: SPM4500BB/93
LG: LGIM-ML208
GlodFly: GF-OP718
Newmen: MS0270 (www.newmen.com.cn
)
Agiler: AGM-018LU (www.agilertech.com)
Citu: CH-3090 (www.citu.cn
)
2. Support USB external DVD backup
Recommended USB external DVD model list:
LG GSA-E10L
BENQ EW164B
Samsung SE-S164
3. Support DS-1000KI network keyboard
4. Support E-SATA HDD backup
E-SATA interface in DS-8000HCI-S, DS-8000HFI-S series DVR is optional. 1
st
internal
SATA interface can be extended to E-SATA (external SATA) interface. In DVR “Recording” menu,
you can select 1
st
SATA HDD as either “Recording” or “Backup” work mode.
User Manual of DS-8000-S Series Net DVR
Page 5 Total 121
If you select “Backup” mode, in DVR “Playback” menu, you can select SATA HDD for
backup.
5．Solved old version some bugs
VGA black screen and Aux audio output issues
User Manual of DS-8000-S Series Net DVR
Page 6 Total 121
Chapter1 Product Introduction
1.1 Summary
DS-8000-S series network digital video recorder is an excellent digital surveillance product.
It uses the embedded MCU and embedded operating system (RTOS), combining the most
advanced technology in Information Industry such as video and audio encoding/decoding, hard
disk record and TCP/IP. The firmware is burned in the flash, more stable and reliable.
DS-8000-S series device has both the features of digital video recorder (DVR) and digital
video server (DVS). It can work stand alone, also be used to build a powerful surveillance network,
widely used in bank, telecommunication, transportation, factories, warehouse, irrigation, etc.
1.2 Model Description
1.3 Features
Compression
z Support 16 channnels video input (PAL/NTSC) at most. Each channel is independent,
H.264 hardware compression and real time (PAL: 25 FPS, NTSC: 30FPS). Support both
variable bitrate and variable frame rate.
z Support 16 channels audio input at most. Each channel is independent, OggVorbis
compression and bitrate is 16Kbps.
DS - 8 0 x x X X I -S
SATA HDD supported
Oversea product
Model name (HC/HF)
Camera number
Embedded DVRDVS code name
Digital Surveillance
User Manual of DS-8000-S Series Net DVR
Page 7 Total 121
z Compressed video and audio are synchronous. You can select either mixed stream or
only video stream.
z Support 4CIF, DCIF, 2CIF, CIF and QCIF resolution.
z Support multi area motion detection.
z Support OSD and changeable OSD position.
z Support LOGO and changeable LOGO position.
Local functions
Record
z Support multiple record type, including real time, manual record, motion detection,
external alarm, motion&alarm, motion|alarm.
z Support 8 SATA HDDs and each HDD can support 2000GB maximum.
z Support FAT32 file system.
z Support HDD S.M.A.R.T technology.
z Support cycle or none cycle record.
z Support backup the recorded files and clips. Support USB memory, USB HDD, USB
CD-R/W, USB DVD-R/W and SATA HDD for backup.
Preview and playback
z Support BNC analog moniotor and VGA output for main output
z Support one aux video and audio input
z Support multiple preview modes.
z Support sensitive area mask.
z Support camera spiteful block alarm.
z Support 2-ch synchronous playback. Support play forward, backward, pause, frame by
frame, etc.
z Support play back by files or by time.
z Display local record status.
PTZ
z Support many kinds of PTZ protocol.
z Support preset, sequence and cruise.
Alarms
z Support exception alarm, motion detection alarm, external alarm, etc.
Others
z Support IR control.
z Support RS-485 keyboard.
z Support multi-level user management.
User Manual of DS-8000-S Series Net DVR
Page 8 Total 121
Network
z Support TCP, UDP, RTP, Multicast for network preview.
z Support PPPoE for board band dialup.
z Support PSTN for narrow band dialup.
z Support remote parameters setup.
z Alarm information can be sent to remote center.
z Network control PTZ.
z Network record the real time stream.
z Network download and playback the recorded files in DVR.
z Remote upgrade the firmware.
z RS-232 supports transparent channel function so that the remote PC can use DVR to
control serial devices.
z Supprot bi-direction voice talk or one-way voice broadcast.
z Support IE to preview and config DVR.
z Support log.
Development support
z Provide network SDK.
z Provide client demo source code.
User Manual of DS-8000-S Series Net DVR
Page 9 Total 121
Chapter2 Installation
Warning: Before you install the DVR, please make sure the power of DVR is switched
off.
2.1 Checking the DVR and Its Accessories
When you get the product, check that all the items are included in your product package.
There is a list in the package. If any of the items is missing, please contact your dealer.
2.2 HDD Installation
Installation notice
The DVR has not HDD when leaving factory. Based on the record schedule, you can
calculate the total capacity you need (refer to Appendix A). Please ask the specialist to
disassembly the DVR and install HDD.
Installation instrument
One cross screw driver.
HDD installation
1. Open the DVR box.
2. Take off the HDD mounting plate.
3. Place the HDD on the mounting plate and fix it with screw.
4. Fix the mounting plate in the DVR.
5. Connect the ATA data cable correctly. The cable has three connctors for DVR main board,
master HDD and slaver HDD.
6. Plug the HDD power connector.
7. Cover and fix the DVR box.
Note: After you install the HDD, you must format them. Please refer to section 6.4.
User Manual of DS-8000-S Series Net DVR
Page 10 Total 121
2.3 Rear Panel Description
Notice: Please refer to real product for different model.
2.3.1 4-ch DS-8004HFI-S Rear Panel
LI NE I N
AAUX
VAUX
VGA
RS-232 UTP
70706060606040404040
230
7070
KEYBOARD
VOUT
AOUT
2
34GG
2GGG
1
1G
1 2
ON
↓
SW1
2 3 41
VI N
AI N
RS-485
T+ T- R+R-
OUT
ALARM
IN
IN
ESATA
Index Physical Interface Description
1
Video Input
Standard BNC.
Audio Input
Standard BNC.
2
Main video Output
Connect CCTV monitor, output video and menu.
Main audio Output
Local audio output.
3
Aux video output
Spot monitor for video preview and playback.
Aux audio output
Spot monitor for audio preview and playback.
Line In
Audio line input for voice talk.
USB Interface
USB memory disk, USB HDD, USB CD-R/W, USB DVD
or USB mouse
4
VGA Interface
VGA display.
5
Keyboard Interface
One is for DS-1000KI keyboard, and the other is for DVR
cascade. Using Pin3 and Pin4.
RS-232
Connect RS-232 devices. Refer to Appendix B for pin
definition.
UTP Network Interface
Connect network devices. Refer to Appendix B for pin
definition.
6
SW1
RS-485 terminal resistor switch. Default is off. The
resistor is 120Ohm.
RS-485
PTZ connection. Using T+/T- to connect PTZ.
User Manual of DS-8000-S Series Net DVR
Page 11 Total 121
External Alarm Input
4 sensor alarm in.
Relay Output
2 replay output.
7
GND
Ground
8
AC Input
100~240VAC
9
E-SATA
Optional. Extend 1st internal SATA to E-SATA.
2.3.2 4-ch DS-8004HCI-S Rear Panel
Index Physical Interface Description
1
Video Input
Standard BNC.
Audio Input
Standard BNC.
2
Main video Output
Connect CCTV monitor, output video and menu.
Main audio Output
Local audio output.
3
Line In
Audio line input for voice talk.
USB Interface
USB memory disk, USB HDD, USB CD-R/W, USB DVD
or USB mouse
4
VGA Interface
VGA display.
5
Keyboard Interface
One is for DS-1000KI keyboard, and the other is for DVR
cascade. Using Pin3 and Pin4.
RS-232
Connect RS-232 devices. Refer to Appendix B for pin
definition.
UTP Network Interface
Connect network devices. Refer to Appendix B for pin
definition.
6
SW1
RS-485 terminal resistor switch. Default is off. The
resistor is 120Ohm.
User Manual of DS-8000-S Series Net DVR
Page 12 Total 121
RS-485
PTZ connection. Using T+/T- to connect PTZ.
External Alarm Input
4 sensor alarm in.
Relay Output
2 replay output.
7
GND
Ground
8
AC Input
100~240VAC
9
E-SATA
Optional. Extend 1st internal SATA to E-SATA.
2.3.3 8-ch/16-ch HCI-S/HFI-S Rear Panel
1 2
ON
↓
1 2 3 4 5 6 7 8 9 10111213141516
VI N
AI N
VOUT
AOUT
AUX
VOUT AOUT L I NE I N
SW1
VGA
RS- 2 3 2 E T HE RNE T
GG D+ D-
RS- 485 KB IN OUT
1G 2 3G4GG0G
ALARM
IN
1234 5678910
11 12 13 14 15 16
T+ T- R+
R-
GG
70706060606040404040
230
7070
ESATA
DS-8008HCI-S/DS-8008HFI-S Rear Panel
1 2
ON
↓
1 2 3 4 5 6 7 8 9 10111213141516
VI N
AI N
VOUT
AOUT
AUX
VOUT AOUT L I NE I N
SW1
VGA
RS- 2 3 2 E T HE RNE T
GG D+ D-
RS- 485 KB I N OUT
1G 2 3G4GG0G
ALARM
IN
1234 5678910
11 12 13 14 15 16
T+ T- R+
R-
GG
70706060606040404040
230
7070
ESATA
DS-8016HCI-S/DS-8016HFI-S Rear Panel
Index Physical Interface Description
1
Video Input
Standard BNC.
Audio Input
Standard BNC.
2
Aux video Output
Spot monitor for video preview and playback.
Aux audio Output
Spot monitor for audio preview and playback.
User Manual of DS-8000-S Series Net DVR
Page 13 Total 121
3
Main video output
Main monitor for video and menu.
Main audio output
Main monitor for audio preview and playback.
4
Line In
Audio line input for voice talk.
5
VGA Interface
VGA display.
6
RS-232
Connect RS-232 devices. Refer to Appendix B for pin
definition.
UTP Network Interface
Connect network devices. Refer to Appendix B for pin
definition.
7
USB Interface
USB memory disk, USB HDD, USB CD-R/W, USB DVD
or USB mouse.
8
E-SATA
Optional. Extend 1st internal SATA to E-SATA.
9
SW1
RS-485 terminal resistor switch. Default is off. The
resistor is 120Ohm.
10
RS-485
PTZ connection. Using T+/T- to connect PTZ.
Keyboard Interface
Using D+/D- for keyboard and DVR cascade connection.
External Alarm Input
16 sensor alarm in.
Relay Output
4 replay output.
11
GND
Ground
12
AC Input
100~240VAC
User Manual of DS-8000-S Series Net DVR
Page 14 Total 121
2.4 External Alarm In/Out Connection
Alarm output connection
Please note the usage of jumper JJ1. If you use DC, either of connections is OK. We suggest
you to use those DC under 12V, 1A.
If you use AC, please open the jumper. There are 4 jumpers (JJ1, JJ2, JJ3 and JJ4) in DVR
main board, corresponding with 4 alarm output. The default is closed.
Warning: If you use AC input for relay output, please open the jumpers.
Alarm input port (drp node):
G (GND): Conenct the GND of sensor.
1~8: Alarm input, support normal
open/normal close.
0: Reserved.
Alarm output:
1G~4G: 4 relay output.
User Manual of DS-8000-S Series Net DVR
Page 15 Total 121
Chapter3 Operational Instructions
3.1 Front Panel
This picture is the front panel of DS-8000-S series Net DVR.
o n p q
r s t u
Index Type Name Description
1 IR receiver.
2 State
Lamps
1-8 Show channel 1-8 status. Green means recording; Red means
network transmission; Orange means recording and network
transmission. Lamp twinkle and red means the corresponding
HDD has error.
3 State
Lamps
9-16 Show channel 1-16 status. Green means recording; Red
means network transmission; Orange means recording and
network transmission.
4 POWER POWER Device switch with power indicator lamp. Green means DVR
is working; Red means DVR is powered off; No light means
no power is supplied.
5 State
Lamps
READY
STATUS
ALARM
MODEM
HDD
LINK
Tx/Rx
DVR is ready.
Green means you can use IR remote control.
Red means there is alarm.
Green means modem connection and dial-up successful.
Twinkle in red means reading or writing HDD.
Green means network is OK.
Twinkle in green means data is being transmitted.
6 Compound
Keys
MENU
ESC
PLAY
1. Switch preview mode into menu;
2. Brush control short key【WIPER】.
Cancel and back to parent menu.
1. Local playback;
User Manual of DS-8000-S Series Net DVR
Page 16 Total 121
REC
EDIT
PTZ
A
PREV
INFO
Main/Aux
2. 【AUTO】in PTZ mode.
1. Manual record;
2. 【SHOT】in PTZ mode (adjust preset).
1. In edit state, delete current cursor character;
2. 【IRIS+】 in PTZ control;
1. Select 9 or × to enable or disable.
1. Enter into PTZ control mode;
2. 【IRIS-】in PTZ control.
1. Input switch (number, lower case, upper case and
symbol);
2. 【FOCUS+】in PTZ control;
3. In preview mode, display or hide the channel status bar.
1. Multi screen preview switch;
2. Switch menu mode into preview;
3. 【FOCUS-】in PTZ control.
【ZOOM+】in PTZ control.
1. 【ZOOM-】in PTZ control.
2. Switch main/aux video output control mode.
7 Input
Keys
Numeric
Keys
F1
F2
Input number, lower case, upper case character and symbols.
【LIGHT】in PTZ control.
【AUX】in PTZ control.
8 Control
Keys
Direction
Keys
ENTER
Composed of 【Ç】,【È】,【Å】and【Æ】.
1. Menu mode, use【Å】/【Æ】 to select 【Ç】/【È】 to
edit;
2. PTZ direction control;
3. Playback speed control.
1. Menu confirmation;
User Manual of DS-8000-S Series Net DVR
Page 17 Total 121
2. Select 9 or × to enable or disable;
3. Pause playback.
User Manual of DS-8000-S Series Net DVR
Page 18 Total 121
3.2 IR Controller
Index Name Description
1 POWER Turnoff device.
2 DEV Enable/Disable IR remote control
3 Numeric Keys Same as numeric keys of front panel.
4 EDIT Same as EDIT key of front panel.
5 A Same as A key of front panel.
6 REC Same as REC key of front panel.
7 PLAY Same as PLAY key of front panel.
8 INFO Same as INFO key of front panel.
9 VOIP
Same as [Main/Aux] key of frint
panel.
10 MENU Same as MENU key of front panel.
11 PREV Same as PREV key of front panel.
12
Direction Keys
ENTER
Same as direction keys and enter key
of front panel.
User Manual of DS-8000-S Series Net DVR
Page 19 Total 121
13 PTZ Same PTZ key of front panel.
14 ESC Same as ESC key of front panel.
15 Reserved
16 F1
Same as【F1】key of front panel.
17 Lens control
IRIS, FOCUS ZOOM for lens
control.
18 F2
Same as【F2】key of front panel.
Loading the batteries into the IR controller
1. Remove the battery cover.
2. Insert the battery. Please take care that the poles (+ and -) are correctly positioned.
3. Replace the battery cover.
Start to use IR controller
Press【DEV】key, input the DVR device ID (default is “88”, can be changed in “Display”
menu) and then press【ENTER】key. If the “STATUS” lamp of DVR front panel is turned into
green, it means you can use IR controller to operate this DVR.
Stop using IR controller
When IR controller status is on, press【DEV】key again, the “STATUS” lamp will be turned
off. The IR controller can not control this DVR.
Switch the DVR off
When IR controller status is on, press【POWER】key for several seconds, the DVR will be
powered off.
When IR controller can not work normally
z Check batteries poles.
z Check the remaining charge in the batteries.
z Check IR controller sensor is mask.
Please change another IR controller to try again. It the problem is still existed, please contact
administrator.
User Manual of DS-8000-S Series Net DVR
Page 20 Total 121
3.3 Menu Description
3.3.1 Menu Items
Menu Name Function Menu Name Function
Display
Video standard
Brightness
Menu transparency
Unit name
Device ID
Require password
Screen saver time
VGA resolution
Date and Time
Image
Camera name and position setup
Adjust Brightness, Contrast, Hue
and Saturation
OSD Display mode, position and
OSD format setup
Mask area setup
View tampering area and response
setup
Video signal loss
Motion detection sensitivity, area
and response setup
Recording
Overwrite/Stop recording
Resolution and recording
parameters setup
Record schedule
PreRecord time
PostRecord time
Network
DVR IP address
DNS IP
Multicast IP address
Remote host IP and port
NAS IP and directory
PPPoE username and password
Alarms
Alarm input type (Normal open/
Normal close)
Alarm response and PTZ linkage
Alarm output and schedule
Exceptions
Exceptions type
Exceptions response
PTZ
PTZ parameters
Preset setup
Sequence setup
Cruise setup
RS232
RS232 parameters
RS232 work mode
Preview
Preview mode
Switch time
Enable/Disable audio preview
Preview layout
User
Password
Add or delete user
Password setup or modification
User rights setup
User Manual of DS-8000-S Series Net DVR
Page 21 Total 121
Transacti on
Text input mode
ATM IP address
ATM type
Text information
Utilities
Restore parameters
Upgrade firmware
HDD management
Clear alarm output
Reboot
Power off
Vie w l o g
System information
3.3.2 Menu Operation
How to enter into menu mode
z Press【MENU】key to enter into DVR main menu.
z Press【PLAY】short key to enter into playback menu.
z Perss【REC】short key to enter into manual record menu.
z Perss【PTZ】short key to enter into PTZ control interface.
Notes: You must input user name and password. The default user name is “admin” and
password is “12345”.
Main Menu Description
The main menu interface is following:
There is one small rectanglar frame named “Active Frame”. It can be moved from one icon to
another by using 【Æ】or【Å】key. When the “Active Frame” is located on one icon, you can press
User Manual of DS-8000-S Series Net DVR
Page 22 Total 121
【ENTER】key to enter into the secondary menu. For example, move the “Active Frame” to
“Image” icon, press 【ENTER】to enter into the secondary menu as following:
Each menu contains different kinds of items. There is a small rectangular frame named
“Active Frame” which is pointing to the selected item. This “Active Frame” can be moved by
【Æ】or【Å】keys. There are such kinds of menu items:
a) Check Box: Provide 2 options, “9” means enable and “×” means disable. You can use
【ENTER】or【EDIT】key to switch over.
b) List Box: Provide more than 2 options. However, only one of them can be selected. You
can use【↑】and【↓】to select one option. For example, on the right side of “Select
Camera”, there is a list box for you to select one camera.
c) Edit Box: This is for you to input characters. Press【EDIT】key to enter into edit status,
you can input characters as following:
i. Press【A】key to select number, upper case, lower case or symbols;
ii. Use【Æ】and【Å】keys to move cursor;
iii. Use【EDIT】key to delete the charcter in front of cursor;
iv. Press【ENTER】or【ESC】to exit edit.
d) Button: Excute a special function or enter into next sub-menu. For example, press
“Policy” button to enter into sub-menu. Press【Confirm】to save parameters and return
User Manual of DS-8000-S Series Net DVR
Page 23 Total 121
to parent menu. Press【Cancel】button to cancel and return to parent menu. The button in
grey means it can be operated only after it is enabled.
How to exit menu
Press【PREV】key to exit menu and return to preview mode.
User Manual of DS-8000-S Series Net DVR
Page 24 Total 121
3.4 Character Input
In the menu interface, if you enter into edit status (for example, in the “camera name” edit
box), at the bottom of screen, the input status is appeared:
Here it means you can press numeric keys to input digital number.
Press【A】key to change input methods. You can select “number”, “Uppercase”, “Lowercase”
or “Symbol”.
Uppercase
Lowercase
Symbol
There are 24 symbols in all. They are divided into 4 pages, and you can use【0】key to turn over
page.
User Manual of DS-8000-S Series Net DVR
Page 25 Total 121
Chapter4 Basic Operation Guide
4.1 Power on
Note: Please make sure the power supply matches DVR and AC cable connected
correctly. Before switch DVR on, please connect one monitor with VOUT or VGA interface.
Otherwise, you can not see graphic user interface and can not operate.
If【POWER】lamp is off, please do as following:
Step1: Connect AC cable correctly;
Step2: Switch on the power button on the real panel.
If【POWER】lamp is in red, just press【POWER】button to start DVR.
When DVR is started,【POWER】lamp is in green. On the monitor or VGA display, DSP and
HDD initialization process will be shown.
The first line represents DSP initialization. If the DSP icon is “×”, it means that the DSP is
initialized error, please contact administrator at once.
The second line represents HDD initialization. Icons of IDE1 master and slaver HDDs, IDE2
master and slaver HDDs, etc are displayed. If the HDD icon is “×”, it means the corresponding
HDD is not installed or not detected. If HDD is not detected, please contact administrator.
Note: If HDD is not installed or not detected, DVR will beep for alarm. You can disable the
alarm option in “Exceptions” menu.
4.2 Preview
DVR will enter into preview mode after it is started.
On preview screen, you can see date, time, camera name and camera status icon.
Set system date and time in “Display” menu, referring to 5.2.9; Change camera name in
“Image” menu, referring to 5.3.2.
In the screen, it will display record and alarm status of each camera. These two kinds of
status will switch over automatically.
User Manual of DS-8000-S Series Net DVR
Page 26 Total 121
Press【A】key to display or hide the camera status bar.
Camera record status is following:
Icon Icon Color Status Description
White No video signal
Yellow Vdieo input
Pink Manual recording
Green Real time recording
Blue Motion detect recording
Red External alarm recording
User Manual of DS-8000-S Series Net DVR
Page 27 Total 121
Camera alarm status is following:
Icon Icon Color Status Description
White Video signal lost
Yellow View tampering alarm
Pink Motion&External alarm
Green No alarm
Blue Motion alarm
Red External alarm
Press numeric keys to switch over individual camera preview. If DVR has less than 10
channels, press one numeric key to switch corresponding channel. For example, press【2】key to
preview 2
nd
camera. If DVR has 10 or more than 10 channels, press two numeric keys to
switch corresponding channel. For example, press 【0】【2】to preview 2
nd
camera; and press
【1】【2】keys to preview 12
th
camera.
Press【EDIT】key to manual cycle preview. You can set the auto preview mode in “Preview”
menu, referring to 5.11.
Press【PREV】key to switch multi-screen perview.
User Manual of DS-8000-S Series Net DVR
Page 28 Total 121
4.3 User name and password
Note: When DVR is delivered from factory, there is only one default administrator
named “admin”, and password is “12345”. The administrator’s name can not be modified,
while the password can be modified. The administrator can create 15 users and define their
user rights.
Login
Login dialog is following:
Use【Ç】/【È】keys to select one user, perss【Æ】key to enter into “Password” edit box, input
corresponding password, press【ENTER】key to exit edit box. The “Active Frame” will be moved
to “Confirm” button. Press【ENTER】key to enter into main menu. If there is beeper alarm, it
means the user name and password are not matched. After three error times, DVR will enter into
preview mdoe.
Modify password
For those users created by admin, they can modify their password as following:
Step1: Enter into main menu
Press【MENU】key, in the login dialog, select your user name, input the correct password, you
can enter into the main menu.
User Manual of DS-8000-S Series Net DVR
Page 29 Total 121
Setp 2: Enter into password modification menu
Move the “Active Frame” to “Password” icon by using【Æ】/【Å】keys. Press【ENTER】
key to enter into following password menu:
Step 3: Input new password
Press【EDIT】key to enter into edit box. You can use numeric keys to input new password.
The password can be null. It also can be 16 numerals. Press【ENTER】to exit edit box, and move to
“Verify” item to input the verify password.
Note: In edit box, use 【Æ】/【Å】to move cursor and【EDIT】key to delete the numeral
in front of the cursor.
Step 4: Modify password successfully
Move the “Active Frame” to “Confirm” button, press【ENTER】key. If the password is
User Manual of DS-8000-S Series Net DVR
Page 30 Total 121
modified successfully, you will get the main menu. Or an error dialog will be pop up. You can
repeat step 3 to modify again.
4.4 PTZ Control
Note: The user must have the “PTZ control” right.
PTZ control interface
In preview mode, press【PTZ】key, in the login dialog, select one user name and input the
correct password, you can enter into PTZ control interface.
In menu mode, press【PTZ】key, you can enter into PTZ control interface directly.
There is “PTZ Control” prompt in the PTZ control interface. The displayed camera name
means which channel’s PTZ is under control. For example, “Camera 01” means you are
controlling the 1
st
camera PTZ.
Select channel
In PTZ control mode, you can press numeric keys to select channel. If DVR has less than 10
channels, press one numeric key to select. For example, press【2】key to selct 2
nd
camera PTZ. If
DVR has 10 or more than 10 channels, you must press two numeric keys to select. For
example, press【0】【2】to select 2
nd
camera PTZ, and press【1】【2】to select 12th camera PTZ.
After you select the camera PTZ, you can use the short keys to control PTZ.
PTZ control keys description
Loading...