Hikvision DS-2DF5232X-AE3, DS-2DF5232X-AEL, DS-2DF6225X-AEL, DS-2DF6A436X-AEL, DS-2DF6A836X-AEL Quick Start Guide

...

Network Speed Dome

Quick Start Guide

UD06820B

Network Speed Dome·Quick Start Guide

Quick Start Guide

Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual.

About this Manual

This Manual is applicable to Network Speed Dome.

The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website (http://overseas.hikvision.com/en/).

Please use this user manual under the guidance of professionals.

Trademarks Acknowledgement

and other Hikvision’s trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR

Network Speed Dome·Quick Start Guide

USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.

0505001070817

iii

Network Speed Dome·Quick Start Guide

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.

For more information see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is

marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Warnings Follow

these safeguards to prevent serious injury or death.

Cautions Follow these precautions to prevent potential injury or material damage.

Network Speed Dome·Quick Start Guide

Safety Instruction

These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.

The precaution measure is divided into Warnings and Cautions:

Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage.

Warnings

 In the use of the product, you must be in strict compliance with the electrical safety

regulations of the nation and region.

 Refer to technical specifications for detailed information.  Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited

Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Refer to technical specifications for detailed information.

 Do not connect several devices to one power adapter as adapter overload may cause

over-heating or a fire hazard.

 Make sure that the plug is firmly connected to the power socket.  Make sure that the power has been disconnected before you wire, install or dismantle

the speed dome.

 When the product is mounted on wall or ceiling, the device shall be firmly fixed.  If smoke, odor or noise rise from the device, turn off the power at once and unplug

the power cable, and then contact the service center.

 If the product does not work properly, contact your dealer or the nearest service

center. Never attempt to disassemble the speed dome yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)

Cautions

 If the speed dome fails to synchronize local time with that of the network, you need

to set up speed dome time manually. Visit the speed dome (via web browser or client software) and enter system settings interface for time settings.

 Make sure the power supply voltage is correct before using the speed dome.

Network Speed Dome·Quick Start Guide

 Do not drop the speed dome or subject it to physical shock, and do not expose it to

high electromagnetism radiation. Avoid installation on vibrations surface or places subject to shock (ignorance can cause device damage).

 Do not touch senor modules with fingers. If cleaning is necessary, use clean cloth with

a bit of ethanol and wipe it gently. If the speed dome will not be used for an extended period, replace the lens cap to protect the sensor from dirt.

 Do not aim the speed dome at the sun or extra bright places. Blooming or smearing

may occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time.

 The sensor may be burned out by a laser beam, so when any laser equipment is in

using, make sure that the surface of sensor will not be exposed to the laser beam.

 Do not place the speed dome in extremely hot, cold, dusty or damp locations, and do

not expose it to high electromagnetic radiation.

 To avoid heat accumulation, good ventilation is required for operating environment.  Keep the speed dome away from liquid while in use.  While in delivery, the speed dome shall be packed in its original packing, or packing of

the same texture.

 Improper use or replacement of the battery may result in hazard of explosion.

Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.

Network Speed Dome·Quick Start Guide

Table of Contents

1 Overview ...................................................................................................... 1

1.1 Speed Dome Overview ............................................................................................ 1

1.1.1 Overview of Type I Speed Dome ....................................................................... 1

1.1.2 Overview of Type II Speed Dome ...................................................................... 1

1.1.3 Overview of Type III Speed Dome ..................................................................... 2

1.1.4 Overview of Type IV Speed Dome ..................................................................... 3

1.1.5 Overview of Type V Speed Dome ...................................................................... 3

1.2 Cable Interfaces ....................................................................................................... 3

1.3 Alarm Output ........................................................................................................... 4

2 Installation ................................................................................................... 5

2.1 Installing Type I Speed Dome ................................................................................... 5

2.1.1 Wall Mounting................................................................................................... 5

2.1.2 In-ceiling Mounting ........................................................................................... 9

2.1.3 Ceiling Mounting ............................................................................................. 11

2.2 Installing Type II Speed Dome ................................................................................ 14

Wall Mounting ......................................................................................................... 14

2.3 Installing Type III Speed Dome ............................................................................... 16

Wall Mounting ......................................................................................................... 16

2.4 Installing Type IV Speed Dome .............................................................................. 19

Wall Mounting ......................................................................................................... 19

2.5 Installing Type V Speed Dome ............................................................................... 22

Wall Mounting ......................................................................................................... 22

3 Setting the Speed Dome over the LAN ....................................................... 27

3.1 Wiring ..................................................................................................................... 27

3.2 Activating the Speed Dome .................................................................................... 27

3.2.1 Activation via Web Browser ............................................................................ 28

3.2.2 Activation via SADP Software .......................................................................... 28

3.3 Modifying the IP Address ....................................................................................... 30

4 Accessing via Web Browser ........................................................................ 32

5 Operating via Hik-Connect App .................................................................. 34

5.1 Enable Hik-Connect Service on Speed Dome ......................................................... 34

5.1.1 Enable Hik-Connect Service via SADP Software .............................................. 34

5.1.2 Enable Hik-Connect Service via Web Browser ................................................. 35

5.2 Hik-Connect Setup ................................................................................................. 35

5.3 Adding Speed Dome to Hik-Connect ..................................................................... 36

5.4 Initializing the Memory Card .................................................................................. 37

Memory Card Slot

Network Speed Dome·Quick Start Guide

1 Overview

1.1 Speed Dome Overview

The network speed dome has five types. The figures below are for reference only, refer to the actual product as the standard.

1.1.1 Overview of Type I Speed Dome

Figure 1-1 Overview of Type I Speed Dome

Figure 1-2 Memory Card Slot

1.1.2 Overview of Type II Speed Dome

Note:

There are two different appearances of Type II speed dome. Refer to the actual product for the location of memory card slot.

Memory Card Slot

Debug

Reset

Memory Card Slot

CARD

Memory Card Slot

Network Speed Dome·Quick Start Guide

Figure 1-3 Overview of Type II Speed Dome

Figure 1-4 Memory Card Slot

1.1.3 Overview of Type III Speed Dome

Figure 1-5 Overview of Type III Speed Dome

Memory Card Slot

Network Speed Dome·Quick Start Guide

1.1.4 Overview of Type IV Speed Dome

Figure 1-6 Overview of Type IV Speed Dome

1.1.5 Overview of Type V Speed Dome

Figure 1-7 Overview of Type V Speed Dome

1.2 Cable Interfaces

The cable interfaces of the speed dome are shown in Figure 1-8. The cables are distinguished by different colors. Refer to the labels attached on the cables for identification.

Notes:

 The cables vary depending on different speed dome models.  Make sure the speed dome is power-off before you connect the cables.

Network Cable

Audio Cable

Alarm Cable

Video Cable

RS-485 Cable

Power Cord

Relay Output

OUT (n)

Direct load

Relay Output

OUT (n)

DC 30V

Power Supply

GND Output

~220V AC

FireWire

Zero Line

JQC-3FG

Relay

(10A 250VAC)

Network Speed Dome·Quick Start Guide

Figure 1-8 Cable Interfaces

1.3 Alarm Output

Alarm output is shown in Figure 1-9.

Figure 1-9 Alarm Output

Network Speed Dome·Quick Start Guide

2 Installation

Before you start:

Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included.

Notes:

 Do not touch the bubble directly by hand. The image blurs otherwise.  Do not power the speed dome up until the installation is finished. To ensure the

safety of personnel and equipment, all the installation steps should be done with power supply off.

 Do not drag the speed dome with its waterproof cables; otherwise the waterproof

performance is affected.

Figure 2-1 Do Not Drag the Cables

2.1 Installing Type I Speed Dome

2.1.1 Wall Mounting

Notes:

 For cement wall, you need to use the expansion screw to fix the bracket. The

mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket.

 For wooden wall, you can just use the self-tapping screw to fix the bracket.  Make sure that the wall is strong enough to withstand more than eight times the

weight of the speed dome and the accessories.

 The bracket in Figure 2-7 is the recommended bracket for this series of speed dome,

and a pendent adapter is required if any other bracket is selected. The dimension of

pendant adapter is G1

Back Box

Bubble

Protective Foam

Lens Cover

Protective Sticker

Network Speed Dome·Quick Start Guide

Steps:

1. Loosen the two lock screws on both sides of the speed dome.

Note:

Do not remove the lock screws from the speed dome.

Figure 2-2 Remove the Bubble

2. Pull the bubble to separate it from the back box, and remove the protective

accessories.

Figure 2-3 Remove the Protective Accessories for Separated Speed Dome

Figure 2-4 Remove the Protective Accessories for Integrated Speed Some

3 4

Network Speed Dome

Ethernet

1: Power Indicator 2: PORT Indicator 3: DATA & POWER OUT 4: DATA IN

Network Speed Dome·Quick Start Guide

3. If the speed dome supports PoE (Power over Ethernet) function, you can switch the

PoE+ and Hi-PoE function for the speed dome. If PoE function is not supported, skip this step.

Figure 2-5 PoE+ and Hi-PoE Switch

Note:

If you choose Hi-PoE, a Hi-PoE adapter must be connected. The Hi-PoE module connection is shown in Figure 2-6.

Figure 2-6 Hi-PoE Connection

Connecting Hi-PoE

Steps:

1) Connect the Hi-PoE module to the Internet via the DATA IN interface with a

network cable.

2) Connect the Hi-PoE module to the speed dome via the DATA & POWER OUT

interface with a network cable.

3) Power on the Hi-PoE module.

4. Install the memory card.

5. Align the cuts on the bubble with the lock screws on the back box to reinstall the

bubble. Tighten the lock screws.

+ 31 hidden pages