TURBO HD
1080P Turret &Bullet Camera
User Manual
Regulatory Information
FCC Information
FCC compliance: This equipment has been
tested and found to comply with the limits for a
dig ital de vice, p ursuan t to part 1 5 of the FC C
Rul es. The se limi ts are de signe d to provi de
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
gen erates , uses, a nd can rad iate rad io
frequency energy and, if not installed and used
in accordance with the instruction manual, may
cau se harm ful inte rferen ce to rad io
communications. Operation of this equipment in
a residential area is likely to cause harmful
interference in which case the user will be
req uired to c orrec t the inte rferen ce at his o wn
expense.
FCC Conditions
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. Th is devi ce may not c ause ha rmful
interference.
2. Th is devi ce must a ccept an y inter ferenc e
received, including interference that may
cause undesired operation.
EU Conformity Statement
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points.
For more information see:
www.recyclethis.info.
2006/66/EC (battery directive):
This product contains a battery that
cannot be disposed of as unsorted
municipal waste in the European
Union.
See the product documentation for specific
batt ery inf ormati on. Th e batter y is marke d with
thi s symbo l, whic h may incl ude let tering t o
ind icate ca dmium ( Cd), le ad (Pb) , or merc ury (Hg ).
UD.6L0201D1550A01
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European
Union. For proper recycling, return
this product to your local supplier
This product and - if applicable - the
supplied accessories too are marked
wit h "CE" an d compl y theref ore with
the applicable harmonized European
stan dards l isted u nder the L ow Volta ge Direc tive
2006/95/EC, the EMC Directive 2004/108/EC,
the RoHS Directive 2011/65/EU.
1.2 Overview
1.2 .1 Over view of Ty pe I Came ra
1.2 .2 Over view of Ty pe Came ra
II
HD Video Cable
CVBS Cable
Switch Cable
Enclosure
Zoom & Focus
Lock ButtonLock Button
Mounting Base
Camera
Power C able
Power C able
IR LED
Lens
Main Body
Sun Shield
Mounting Base
Switch Cable
HD Video Cable
CVBS Cable
Zoom
Focus
1 Introduction
1.1 Product Features
This camera adopts new generation sensor with
high sensitivity and advanced circuit board design
technology. It possesses the features of high
resolution, low distortion, and low noise, etc. It is
extremely suitable for supervisory system and
image processing system.
The main features are as follows:
l
High performance CMOS sensor and high
resolution bring high-quality image;
l
Low illumination;
l
Support IR cut filter with auto switch;
l
OSD m enu, pa ramete rs are con figur able;
l
Support auto white balance, auto gain control,
electronic shutter control and internal
synchronization;
l
SMART IR mode;
l
Unit transmission control;
l
Advanced 3-axis design meets different
installation requirements.
l Ple ase make s ure tha t the dev ice in th e packag e
is in g ood con ditio n and all t he asse mbly pa rts
are i nclud ed.
l Make s ure tha t all the re lated e quipm ent is
power-off during the installation.
l Check the specification of the products for the
installation environment.
l Che ck whet her the p ower su pply is m atched
wit h your po wer outp ut to avo id dama ge.
l Please make sure the wall is strong enough to
withstand three times the weight of the camera
and the mounting.
l If th e wall is t he ceme nt wall, y ou need t o inser t
exp ansio n screws b efore yo u instal l the cam era.
If the wall is the wooden wall, you can use
sel f-tap ping sc rew to sec ure the c amera.
l If the product does not function properly,
please contact your dealer or the nearest
ser vice ce nter. Do not d isass emble t he came ra
for repair or maintenance by yourself.
2.1 Installation of Type CameraI
Steps:
1.Dr ill the s crew ho les and th e cable h ole on th e
ceiling according to the supplied drill template.
Figure 2-1 The Drill Template
2 Push t he lock b utton t o disas sembl e the cam era
.
from the mounting base.
3.Fix the mounting base to the ceiling.
Figure 2-2 Release The Lock Screw
PUSH
For p roper re cycli ng, retu rn the ba ttery t o your
supplier or to a designated collection point. For
more information see: www.recyclethis.info.
2 Installation
Before you start:
Thank you for purchasing our product. If there
are a ny quest ions, o r reque sts, ple ase do no t
hes itate to c ontact t he deal er.
This manual applies to DS-2CE56D5T-VFIT3 and
DS-2CE16D5T-(A)VFIT3.
Thi s manua l may cont ain sev eral tec hnica l
incorrect places or printing errors, and the
content is subject to change without notice.
The u pdate s will be ad ded to th e new ver sion of
this manual. We will readily improve or update
the products or procedures described in the
manual.
DISCLAIMER STATEMENT
Underwriters Laboratories Inc. (”UL” has not)
tested the performance or reliability of the
security or signaling aspects of this product.
UL ha s only te sted for f ire, sho ck or cas ualty
haz ards as ou tline d in Ul’s St andard (s) for S afety,
UL6 0950- 1. UL Cer tific ation d oes not co ver the
performance or reliability of the security or
sig nalin g aspec ts of thi s produ ct. UL MA KES NO
REPRESENTATIONS, WARRANTIES OR
CERTIFICATIONS WHATSOEVER REGARDING
0100001040603
THE PERFORMANCE OR RELIABILITY OF ANY
SECURITY OR SIGNALING RELATED FUNCTIONS
OF THIS PRODUCT.
Fig ure 1-1 O vervi ew of Type I Ca mera
Fig ure 1-2 O vervi ew of Type Cam eraII
3 Menu Operation
Steps:
1.Dr ill the s crew ho les and t he cable h ole in th e
ceiling according to the supplied drill template.
2.Hammer the supplied plastic expansion bolt into
the s crew ho les.
2.2 Installation of Type II
Camera
Figure 2-5 Drill Template
Figure 2-6 Fix the Camera to the Ceiling
Figure 2-7 3-axis Adjustment
5. Adjust the surveillance angle.
1). Loosen No.1 adjusting screw to adjust the pan
position (0 ~ 360 ).°°
2).Tighten No.1 adjusting screw.
3). Loosen No.2 adjusting screw to adjust the
tilting position(0 ~ 90 ).°°
4).Tighten No.2 adjusting screw.
5). Loosen No.3 adjusting screw to adjust the
rotation position 0 ~ 360 .(° °)
6).Tighten No.3 adjusting screw.
3.Route the cables to the cable hole and connect
the corresponding cables.
4.Fix the camera to the ceiling with the supplied
screws.
4.Route the cables to the cable hole and connect
the corresponding cables.
5.Secure the camera to the mounting base by
tightening the lock screw.
6.Ad just th e camera a ccord ing to the f igure b elow
to get a n optim um angl e.
Figure 2-3 3-axis Adjustment
7.Use the screwdriver to adjust the ZOOM screw
and t he FOCU S screw un til you g et the opt imum
image.
Figure 2-4 Zoom and Focus Adjustment
0 ~360
0 ~75
0~360
Both wall mounting and ceiling mounting are
suitable for type bullet camera. Ceiling mounting
wil l be taken a s an examp le in the s ectio n. And yo u
can take steps of ceiling mounting as a reference
if wall mounting is adopted.
0~360
0~360
0~90
1
2
3
Figure 3-1 Main Menu
Menu
SCENE
LENS
RESET
EXPOSURE
WB
DAY&NIGHT
BACKLIGHT
NR
SPECIAL
ADJUST
INDOOR
OUTDOOR
INDOOR1
LOWLIGHT
MANUAL
SHUTTER
AGC
SENS-UP
BRIGHTNESS
D-WDR
DEFOG
BLC
HSBLC
ATW
AWC-SET
MANUAL
COLOR
B/W
EXT
2DNR
3DNR
CAM
TITLE
D-EFFECT
MOTION
PRIVACY
LAUGUAGE
DEFECT
VERSION
SHARPNESS
MONITOR
LSC
VIDEO.
OUT
EXIT
SETUP
You can c all the m enu and a djust t he came ra
parameters with a coaxial camera controller
(pu rchas e separa tely) . You c an also c all the m enu
with supported TVI DVR.
3.1 VIDEO.OUT
PAL or NTSC is selectable .
3.2 LANGUAGE
Eng lish, J apane se, CHN 1, CHN2 , Korean , Germa n,
French, Italian, Spanish, Polish, etc., are selectable.
3.3SETUP
3.3.1 SCENE
You can select indoor, outdoor, indoor 1 and low
-li ght as th e worki ng envir onmen ts.
3.3.2 LENS
The c amera is e quipp ed with a f ixed le ns.
3.3.3 EXPOSURE
EXPOSURE
1. SHUTTER AUTO
2. AGC OFF
3. SENS-UP ---
4. BRIGHTNESS ---|------ 40
5. DEFOG OFF
6. D-WDR OFF
7. RETURN RET
Figure 3-2 Exposure
SHUTTER: AUTO ,1/25 , 1/50, F LK, 1/2 00, 1/4 00,
1/1 k, 1/2k , 1/5k, 1 /10k, 1 /50k, x 2, x4, x6 , x8, x10 ,
and x15 are selectable.
: You can s et the AG C value fr om 0 to 15.AGC
: You can s et the SE NS-UP t o OFF or AUT O.SENS-UP
: You can s et the br ightn ess valu eBRIGHTNESS
fro m 1 to 100.
: You can s et the de fog func tion as O N toDEFOG
enable the function. Position, size, and the defog
gradation are configurable.
You can s et the D- WDR as ON o r OFF.D-WDR:
3.3.4 Backlight
Backlight Compensation (BLC):
Set t he gain of B LC as Hig h, Midd le, or Lo w.-GAIN:
Press the up/down/left/right button to-AREA:
define the BLC position and size. Select RET or
AGA IN to go bac k the BLC m enu or re -defi ne the
BLC a rea.
Rest ore the B LC setti ngs to th e defaul t.-Default:
HSBLC: Select an HSBLC area. Set the DISPLAY
status as ON. Press the up/down/left/right button
to de fine th e area pos ition a nd size . Set the H SBLC
LEVEL from 0 to 100. Select ALL DAY or Night for the
HSB LC mode . Set the B LACK MAS K statu s as ON or
OFF.
HSBLC
1. SELECT AREA1
2. DISPLAY ON 8
3. LEVEL ---|------40
4. MODE ALL DAY
5. BLACK MASK ON
6. DEFAULT 8
7. RETURN RET
Fig ure 3-3 H SBLC
3.3.5 White Balance (WB)
MANUAL, ATW (Auto-tracking White Balance),
AWC→SET are selectable.
3.3 .6 Day & Ni ght
Color, B/W, and EXT are selectable for DAY and
NIGHT switches.
3.3.7 NR
: You can s et 2D NR sta tus as ON o r OFF.2D NR
: Set the Smart NR status as ON and adjust3D NR
the 3 D smart N R sensi tivit y ranges f rom 0 to 10 0.
Set t he 3D NR LE VEL rang es from 0 t o 100. Set t he
2D&3D NR
1. 2DNR OFF
2. 3DNR ON
8
3. RETURN RET
3D NR
1. SMART NR ON
8
2. LEVEL ------|--8 0
3. START. AGC - |--------10
4. END. AGC -|--------10
5. RETURN RET
Fig ure 3-4 N R
Fig ure 3-5 3 D NR
3.3.8 SPECIAL
Edi t the came ra titl e on this s ectio n.Camera Title:
D-effect:
Set t he freez e funct ion as ON o r OFF.-FREEZE:
OFF, MI RROR, V -FLIP, and R OTATE a re-MIRROR:
selectable for mirror.
Define the zoom area by configuring-D-ZOOM:
the p ositi on from PAN & T ILT.
The D-Zoom area, sensitivity-SMART D-ZOOM:
and time are configurable.
Set t he NEG IM AGE as ON or O FF.-NEG.IMAGE:
SPECIAL
1. CAM TITLE ON
8
2. D-DFFECT 8
3. MOTION OFF
4. PRIVACY OFF
5. LANGUAGE ENG
8
6. DEFECT 8
7. RETURN RET
Figure 3-6 Special
MOTION
1. SELECT AREA 1
2. DISPLAY ON8
3. SENSITIVITY ----|----30
4. MOTION VIEW ON
5. DEFAULT 8
6. RETURN RET
Fig ure 3-7 M otion D etecti on
Motion: Select a MOTION area. Set the DISPLAY
status as ON or OFF. Press the up/down/left/right
but ton to def ine the p ositi on and si ze of the a rea.
Set t he SENS ITIVI TY from 0 to 6 0. Set th e MOTIO N
VIE W status a s ON or OFF.
Privacy: Select a PRIVACY area. Set the DISPLAY
stat us as INV, MO SAIC, C OLOR or O FF. P ress the
up/down/left/right button to define the position
and s ize of the a rea.
Defect: LIVE D PC, STATIC D PC and Bl ack DPC a re
adjustable in this section.
PRIVACY
1. SELECT AREA 1
2. DISPLAY MOS AIC
8
3. COLOR 10
4. TRANS. 1
5. DEFAULT
8
6. RETURN RET
ADJUST
1. SHARPNESS --------|15
2. MONITOR LCD8
3. LSC OFF
4. RETURN RET
3.3.9 ADJUST
: Adjust the sharpness from 0 to 15.Sharpness
: Monitor CRT, and Monitor LCD areMonitor
selectable.
: Set t he LSC sta tus as ON o r OFF.LSC
3.3.10 RESET
Res et all the s ettin gs to the d efault .
3.3.11 EXIT
Pre ss OK to exi t the men u.
START. AGC l evel as t he thre shold t o enabl e AGC,
and s et the EN D. AGC lev el as the t hresho ld to
disable AGC.
Figure 3-8 Privacy Mask
Figure 3-9 Adjust
Loading...