HIKVISION DS-2CD763PF-E, DS-2CD763PF-EI, DS-2CD763PFNF-EI, DS-2CD763PFNF-E, DS-2CD753F-E Installation Manual

...

Download

Network Dome Camera

Installation Manual

V3.0.0

Hangzhou Hikvision Digital Technology Co., Ltd.

http://www.hikvision.com

2010-04

Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. This manual applies to DS-2CD763PF(NF)-E(I), DS-2CD753F-E(I),

DS-2CD793PF(NF)-E(I), DS-2CD793PFWD(NFWD)-E(I) and DS-2CD733F-E(I)

Network Camera. This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual.

DISCLAIMER STATEMENT

“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the security or signaling aspects of this product. UL has only tested for fire, shock or casualty hazards as outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification does not cover the performance or reliability of the security or signaling aspects of this product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.”

Installation Manual of Network Dome Camera

Safety Instruction

These instructions are intended to ensure that the user can use the product correctly to avoid

danger or property loss.

The precaution measure is divided into ‘Warnings’ and ‘Cautions’:

Warnings: Serious injury or death may be caused if any of these warnings are neglected.

Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.

Warnings Follow these safeguards to

prevent serious injury or death.

Cautions Follow these precautions to

prevent potential injury or material

damage.

Warnings:

1. In the use of the product, you must strictly comply with the electrical safety regulations

of the nation and region.

2. Source with DC 12V or AC24V according to the IEC60950-1 standard. Please refer to

technical specifications for more details.

3. Do not connect several devices to one power adapter as an adapter overload may cause

over-heating and can be a fire hazard.If use the POE as the power supply, please make

sure that the POE Switch have the sufficient power.

4. Please make sure that the plug is firmly inserted into the power socket.

5. When the product is installed on a wall or ceiling, the device should be firmly fixed.

Installation Manual of Network Dome Camera

6. If smoke, odor, or noise rise from the device, turn off the power at once and unplug the

power cable, then contact the service center.

7. If the product does not work properly, please contact your dealer or the nearest service

center. Never attempt to disassemble the camera yourself. (We shall not assume any

responsibility for problems caused by unauthorized repair or maintenance.)

Installation Manual of Network Dome Camera

Notice:

1. Make sure the power supply voltage is correct before using the camera.

2. Do not drop the camera or subject it to physical shock.

3. Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with

a bit of ethanol and wipe it gently. If the camera will not be used for an extended period

of time, put on the lens cap to protect the sensor from dirt.

4. Do not aim the camera at the sun or extra bright places. A blooming or smear may occur

otherwise (which is not a malfunction however), and affecting the endurance of sensor at

the same time.

5. The sensor may be burned out by a laser beam, so when any laser equipment is being

used, make sure that the surface of the sensor will not be exposed to the laser beam.

6. Do not place the camera in extremely hot or cold temperatures (the operating

temperature should be between -10°C ~ +60°C, dusty or damp locations, and do not

expose it to high electromagnetic radiation.

7. To avoid heat accumulation, good ventilation is required for a proper operating

environment.

8. While shipping, the camera should be packed in its original packing, or packing of the

same texture.

9. Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment

should be replaced regularly according to their average life time. The average time varies

because of differences between operating environment and usage history, so regular

Installation Manual of Network Dome Camera

checking is recommended for all users. Please contact with your dealer for more details.

Installation Manual of Network Dome Camera

Index

Chapter 1 Introduction..............................................................................................................1

1.1 Network camera Functions and Features .............................................................1

1.2 Applications .....................................................................................................................2

Chapter 2 Installation.................................................................................................................3

2.1 Camera Description and Connection.....................................................................3

2.2 Hardware Installation ...................................................................................................5

Appendix Product Specification .........................................................................................8

DS-2CD763PF(NF)-E(I) ........................................................................................................8

Specification ....................................................................................................................8

Dimensions.......................................................................................................................9

DS-2CD753F-E(I) ................................................................................................................ 10

Specification ................................................................................................................. 10

Dimensions.................................................................................................................... 11

DS-2CD793PF(NF)-E(I) ..................................................................................................... 12

Specification ................................................................................................................. 12

Dimensions.................................................................................................................... 13

DS-2CD793PFWD(NFWD)-E(I)....................................................................................... 14

Specification ................................................................................................................. 14

Dimensions.................................................................................................................... 15

DS-2CD733F-E(I) ................................................................................................................ 16

Specification ................................................................................................................. 16

Installation Manual of Network Dome Camera

Dimensions.................................................................................................................... 17

Installation Manual of Network Dome Camera

Chapter 1 Introduction

Network camera is a kind of embedded digital surveillance product that combines the

features of both traditional analog camera and net DVS (Digital Video Server). Due to the

embedded Linux operation system and the latest Davinci hardware platform of TI, the system

operates with high scheduling efficiency. Furthermore, the firmware is burned in the flash,

which makes the product small, reliable and highly stable.

1.1 Network camera Functions and Features

Functions:

 Network Function: Support the TCP/IP protocols and IE browsing.

 Heartbeat Function: The server can acquire real time operating performance of the

network camera through the heartbeat function.

 Alarm Function: The product includes 2 channel of alarm signal input and 2 channel of

alarm on/off output, and supports motion detection, video loss, Network Broken, IP

address conflict, Storage exception.

 Voice Talking: Support bidirectional voice talking.

 User Management: Support multilevel right management. The administrator can create

up to 15 separate users with different right levels, which highly improves the system

security.

Compression Functions:

 Support 1 channel video signal and standard H.264 encoding compression, which

Installation Manual of Network Dome Camera

supports both variable bit rate and variable frame rate; besides, you can self-define both

the video quality and its compressed bit rate.

Remote Control:

 The product offers a 10M/100M self-adaptive Ethernet interface.

 Support

TCP/IP, HTTP, DHCP, DNS, DDNS, RTP/RTSP, PPPoE, SMTP, NTP protocols.

 Set the parameters, browse real time videos or check the camera performance through

software or IE, and store the compressed bit rate through network.

 Support remote upgrades and maintenance.

1.2 Applications

This camera is ideal for remote control network applications. E.g.:

1. Network surveillance for bank counters, supermarkets and factories.

2. Remote surveillance for nursing homes, kindergartens and schools.

3. AI janitors.

4. AI building/district management systems.

5. Self-service systems of power plants.

6. Pipelining and warehouse monitoring.

7. Surveillance for airdrome, railway station, bus stop etc.

Installation Manual of Network Dome Camera

Chapter 2 Installation

NOTE:

1. Please check if all the items on the package list have been included with your

camera.

2. Read the following contents carefully before the installation.

3. Make sure that all the related equipment is power-off during the installation.

4. Check the power supply to prevent any damage caused by mismatching problems.

5. If the product does not operate properly, please contact your dealer or the nearest

service center. Never attempt to disassemble the camera yourself. Users are

responsible for any problem caused by modification or repairing without

authorization.

2.1 Camera Description and Connection

Camera description:

Camera Connection:

Installation Manual of Network Dome Camera

Serial NO. Description

1 LAN(PoE): 10M/100M self-adaptive Ethernet interface

2 INITIAL SET: Reset all parameters to factory default settings.

3 AUDIO OUT: Audio output interface

4 MIC IN: Audio input interface

5 D+, D-: RS-485 interface

6 1A 1B, 2A 2B: Alarm output interface

7 IN1 GND, IN2 GND: Alarm input interface

8 Power supply

9 SD card slot

10 Video output interface

11 Power LED indicator, which turns red when power is applied to the unit

NOTE:

When the camera is power up, press the “INITIAL SET” button for about 10 seconds,

then all parameters, including user name, password, IP address, port number, etc., will

be reset to the factory default settings.

The alarm input is a NO/NC relay. If the input is not a NO/NC relay, follow the

connection diagram below:

Installation Manual of Network Dome Camera

To connect to an AC/DC load, use the following diagram:

The alarm output is an on/off output that requires external power supply on connection. The

external power supply shall be 12V DC/30mA, or use AC with external relays. Equipment

damage or electric shock may cause if without relays.

2.2 Hardware Installation

The ceiling mount is a suitable installation method for this camera. Please stick to the

following steps:

Installation Manual of Network Dome Camera

1. Use the screws to fix the bottom plate on the ceiling, and rotate dome camera in

anti-clockwise direction to attach it to the bottom plate, and finally use the lock screw to

secure the dome camera into position.

2. Loosen the set screws with a hexagonal screw driver (attached with the camera), and take

down the dome cover.

NOTE:

If required, user can apply the pliers

to remove the clip (refer to the part

Installation Manual of Network Dome Camera

3. While viewing the video on the monitor, adjust the camera’s view angle for your need.

4. Install the dome cover and tighten the screws.

Installation Manual of Network Dome Camera

Appendix Product Specification

DS-2CD763PF(NF)-E(I)

Specification

DS-2CD763PF-E(I) / DS-2CD763NF-E(I)

Model Parameter

1.3 Megapixel 1/3 ”CCD Day&Night Vandal-proof Network Dome Camera

Camera

Image Sensor 1/3 ” SONY Progressive Scan CCD

Signal System PAL / NTSC

Min. Illumination

0.1Lux @(F1.2, AGC ON)

-I :

0.1Lux @(F1.2, AGC ON), 0 Lux with IR

Electronic Shutter

1/25(1/30)s ~1/100,000s

Lens

2.7-9mm @ F1.2

Angle of view: 101°~30.4°

Lens Mount φ14

Auto Iris DC Drive

Adjustment Range

Pan0~360°, Tilt0~75°, Rotation0~360°

Day& Night Electronic (-I: IR cut filter with auto switch)

Compression Standard

Video Compression

H.264/Mjpeg

Bit rate 32 Kbps~16Mbps

Audio Compression

G.711(G.722.1 optional)

Image

Max. Image Resolution

1280 x 960

Frame Rate

50HZ: 12.5fps (1280 x 960), 25fps (1280 x 720)

60HZ: 15fps (1280×960), 30fps (1280 x 720)

Image Settings

Saturation, Brightness, Contrast adjustable through client software or

web browser

Network

Installation Manual of Network Dome Camera

Storage Support SD/SDHC, NAS (ISCSI optional)

Intelligent Alarm

Motion Detection, Video Loss, Network Broken, IP address conflict,

Storage exception

Protocols

TCP/IP, HTTP, DHCP, DNS, DDNS, RTP/RTSP, PPPoE, SMTP, NTP

(SNMP, HTTPS, FTP, SIP, SRTP, 802.1x, IPV6 optional )

Basic

Initial Set Button, Anti-flicker, Dual Stream, Heartbeat, Password

Protection, Watermark

Interface

Audio Input 1 channel microphone input, 3.5mm mini-jack

Audio Output 1 channel 3.5mm audio interface (Line level, 600Ω)

Communication Interface

1 RJ45 10M / 100M self-adaptive Ethernet interface, 1 RS-485

interface

Alarm Input 2 channel

Alarm Output 2 channel

Video Output 1Vp-p Composite Output (75Ω/RCA)

General

Operating Condition

-10 ~60 (14°F~140°F), Humidi℃℃ ty 90% or less(non-condensing)

Power Supply DC12V±10% / PoE (AC24V optional)

Power Consumption

7.5W MAX

-I: 9W MAX(9.5W MAX with ICR working)

Impact Protection

IEC60068-2-75Eh,50J;EN50102, up to IK10

IR Range -I: Within 10-20 meters (32.8-65.6ft)

Dimensions(mm) φ140 × 114 (φ5.5" × 4.9")

Weight 1400g (3.08lbs)

*”I” series supports 10-20 meters (32.8-65.6ft) IR Range

Dimensions

Installation Manual of Network Dome Camera

DS-2CD753F-E(I)

Specification

DS-2CD753F-E(I)

Model Parameter

2 Megapixel 1/3 ” CMOS Day&Night Vandal-proof Network Dome

Camera

Image Sensor 1/3 ” Progressive Scan CMOS

Min. Illumination

0.5Lux @(F1.2, AGC ON), 0.1Lux @(F1.2, AGC ON, Sense-up×5)

-I:

0.5Lux @(F1.2, AGC ON), 0.1Lux @(F1.2, AGC ON, Sense×5) , 0 Lux with IR

Electronic Shutter

1/25s ~1/100,000s

Lens

2.7-9mm @ F1.2

Angle of view: 101°~30.4°

Lens Mount φ14

Auto Iris DC Drive

Adjustment Range

Pan0~360°, Tilt0~75°, Rotation0~360°

Day&Night Electronic (-I: IR cut filter with auto switch)

Compression Standard

Video Compression

H.264/MJpeg

Bit rate 32 Kbps~16Mbps

Audio Compression

G.711(G.722.1 optional)

Image

Max. Image Resolution

1600 x 1200

Frame Rate

50HZ: 12.5fps (1600×1200), 12.5fps (1600×912), 25fps (1280×960),

25fps (1280×720)

60HZ: 15fps (1600×1200), 15fps (1600×912), 25fps (1280×960), 30fps

(1280×720)

Video Parameter

Saturation, Brightness, Contrast adjustable through client software or

web browser

Network

Storage Support SD/SDHC, NAS (ISCSI optional)

Intelligent Alarm Motion Detection, Video Loss, Network Broken, IP address conflict,

Installation Manual of Network Dome Camera

Storage exception

Protocols

TCP/IP, HTTP, DHCP, DNS, DDNS, RTP/RTSP, PPPoE, SMTP, NTP

(SNMP, HTTPS, FTP, SIP, SRTP, 802.1x, IPV6 optional )

Basic

e-PTZ , Initial Set Button, Anti-flicker, Dual Stream, Heartbeat,

Password Protection, Watermark

Interface

Audio Input 1 channel microphone input, 3.5mm mini-jack

Audio Output 1 channel 3.5mm audio interface (Line level, 600Ω)

Communication Interface

1 RJ45 10M / 100M self-adaptive Ethernet interface, 1 RS-485

interface

Alarm Input 2 channel

Alarm Output 2channel

Video Output 1Vp-p Composite Output (75Ω/RCA)

General

Operating Condition

-10 ~60 (14°F~140°F), Humidity 90% or less(non℃℃ -condensing)

Power Supply DC12V±10% / PoE (AC24V optional)

Power Consumption

4.5W MAX

-I: 6W MAX(6.5W MAX with ICR working)

Impact Protection

IEC60068-2-75Eh,50J;EN50102, up to IK10

IR Range -I: Within 10-20 meters (32.8-65.6ft)

Dimensions(mm) φ140 × 114 (φ5.5" × 4.9")

Weight

1400g (3.08lbs)

* ”I” series supports 10-20 meters (32.8-65.6ft) IR Range

Dimensions

Installation Manual of Network Dome Camera

DS-2CD793PF(NF)-E(I)

Specification

DS-2CD793PF-E(I) / DS-2CD793NF-E(I)

Model Parameter

4CIF 1/3 ” CCD Low Illumination Day&Night Vandal-proof Network

Dome Camera

Camera

Image Sensor 1/3 ” SONY CCD

Signal System PAL / NTSC

Min. Illumination

0.02Lux @ (F1.2, AGC ON)

0.027Lux @(F1.4, AGC ON)

-I:

0.02Lux @ (F1.2, AGC ON),0 Lux with IR

0.027Lux @(F1.4, AGC ON), 0 Lux with IR

Electronic Shutter

1/25(1/30)s ~1/100,000s

Lens

2.8-11mm @ F1.4

Angle of view: 97°~24°

Lens Mount φ14

Auto Iris DC Drive

Adjustment Range

Pan0~360°, Tilt0~75°, Rotation0~360°

Day&Night Electronic (-I: IR cut filter with auto switch)

Compression Standard

Video Compression

H.264/MJpeg

Bit rate 32 Kbps~8Mbps

Audio Compression

G.711(G.722.1 optional)

Image

Max. Image Resolution

PAL: 704 × 576

NTSC: 704 × 480

Frame Rate

50HZ:25 fps (704 × 576)

60HZ:30fps (704 × 480)

Image Settings

Saturation, Brightness, Contrast adjustable through client software or

web browser

Network

Storage Support SD/SDHC, NAS (ISCSI optional)

Intelligent Alarm Motion Detection, Video Loss, Network Broken, IP address conflict,

Installation Manual of Network Dome Camera

Storage exception

Protocols

TCP/IP, HTTP, DHCP, DNS, DDNS, RTP/RTSP, PPPoE, SMTP, NTP

(SNMP, HTTPS, FTP, SIP, SRTP, 802.1x, IPV6 optional )

Basic

Initial Set Button, Anti-flicker, Dual Stream, Heartbeat, Password

Protection, Watermark

Interface

Audio Input 1 channel microphone input, 3.5mm mini-jack

Audio Output 1 channel 3.5mm audio interface (Line level, 600Ω)

Communication Interface

1 RJ45 10M / 100M self-adaptive Ethernet interface, 1 RS-485

interface

Alarm Input 2 channel

Alarm Output 2channel

Video Output 1Vp-p Composite Output (75Ω/RCA)

General

Operating Condition

-10 ~60 (14°F~140°F), Humidity 90% or less(non℃℃ -condensing)

Power Supply DC12V±10% / PoE (AC24V optional)

Power Consumption

5.5W MAX

-I: 7W MAX(7.5W MAX with ICR working)

Impact Protection

IEC60068-2-75Eh,50J;EN50102, up to IK10

IR Range -I: Within 20-30 meters (65.6-98.4ft)

Dimensions(mm) φ140 × 114 (φ5.5" × 4.9")

Weight

1400g (3.08lbs)

*”I” series supports 20-30 meters (65.6-98.4ft) IR Range

Dimensions

Installation Manual of Network Dome Camera

DS-2CD793PFWD(NFWD)-E(I)

Specification

DS-2CD793PFWD-E(I) / DS-2CD793NFWD-E(I) Model

Parameter

4CIF 1/3 ”CCD WDR Day&Night Vandal-proof Network Dome Camera

Camera

Image Sensor 1/3" SONY vertical double density interline CCD

Signal System PAL / NTSC

Min. Illumination

0.1Lux @(F1.2, AGC ON)

0.14Lux @(F1.4, AGC ON)

-I:

0.1Lux @(F1.2, AGC ON) , 0 Lux with IR

0.14Lux @(F1.4, AGC ON), 0 Lux with IR

Electronic Shutter

1/25(1/30)s ~1/100,000s

Lens

2.8-11mm @ F1.4

Angle of view: 97°~24°

Lens Mount φ14

Auto Iris DC Drive

Adjustment Range

Pan0~360°, Tilt0~75°, Rotation0~360°

Day&Night Electronic (-I: IR cut filter with auto switch)

Wide Dynamic Range

160X

Compression Standard

Video Compression

H.264/Mjpeg

Bit rate 32 Kbps~8Mbps

Audio Compression

G.711(G.722.1 optional)

Image

Max. Image Resolution

PAL: 704 × 576

NTSC: 704 × 480

Frame Rate

50HZ:25fps (704 × 576)

60HZ: 30fps (704 × 480)

Image Settings

Saturation, Brightness, Contrast adjustable through client software or

web browser

Network

Storage Support SD/SDHC, NAS (ISCSI optional)

Installation Manual of Network Dome Camera

Intelligent Alarm

Motion Detection, Video Loss, Network Broken, IP address conflict,

Storage exception

Protocols

TCP/IP, HTTP, DHCP, DNS, DDNS, RTP/RTSP, PPPoE, SMTP, NTP

(SNMP, HTTPS, FTP, SIP, SRTP, 802.1x, IPV6 optional )

Basic

Initial Set Button, Anti-flicker, Dual Stream, Heartbeat, Password

Protection, Watermark

Interface

Audio Input 1 channel microphone input, 3.5mm mini-jack

Audio Output 1 channel 3.5mm audio interface (Line level, 600Ω)

Communication Interface

1 RJ45 10M / 100M self-adaptive Ethernet interface, 1 RS-485

interface

Alarm Input 2 channel

Alarm Output 2channel

Video Output 1Vp-p Composite Output (75Ω/RCA)

General

Operating Condition

-10 ~60 (14°F~140°F), Humidity 90% or less(non℃℃ -condensing)

Power Supply DC12V±10% / PoE (AC24V optional)

Power Consumption

5.5W MAX

-I: 7W MAX(7.5W MAX with ICR working)

Impact Protection

IEC60068-2-75Eh,50J;EN50102, up to IK10

IR Range -I: Within 10-20 meters (32.8-65.6ft)

Dimensions(mm) φ140 × 114 (φ5.5" × 4.9")

Weight

1400g (3.08lbs)

*”I” series supports 10-20 meters (32.8-65.6ft) IR Range

Dimensions

Installation Manual of Network Dome Camera

DS-2CD733F-E(I)

Specification

DS-2CD733F-E(I) Model

Parameter

VGA 1/4” CMOS Day&Night Vandal-proof Network Dome Camera

Camera

Image Sensor 1/4” Progressive Scan CMOS

Electronic Shutter 1/25s ~1/100,000s

Min. Illumination

0.2Lux @(F1.2,,AGC ON)

0.27Lux @(F1.4, AGC ON)

-I :

0.2 Lux @(F1.2, AGC ON) , 0 Lux with IR

0.27 Lux @(F1.4, AGC ON) , 0 Lux with IR

Lens

2.8-11mm @ F1.4

Angle of view: 70°~18°

Lens Mount φ14

Auto Iris DC Drive

Adjustment Range Pan0~360°, Tilt0~75°, Rotation0~360°

Day / Night Electronic (-I: IR cut filter with auto switch)

Compression Standard

Video Compression

H.264/Mjpeg

Bit rate 32 Kbps~8Mbps

Audio Compression

G.711(G.722.1 optional)

Image

Max. Image Resolution

640×480

Frame Rate

50HZ: 25fps(640×480) 60HZ: 30fps(640×480)

Video Parameter

Saturation, Brightness, Contrast adjustable through client software or

web browser

Network

Storage Support SD/SDHC, NAS ( ISCSI optional)

Intelligent Alarm

Motion Detection, Video Loss, Network Broken, IP address conflict,

Storage exception

Protocols

TCP/IP, HTTP, DHCP, DNS, DDNS, RTP/RTSP, PPPoE, SMTP, NTP

(SNMP, HTTPS, FTP, SIP, SRTP, 802.1x, IPV6 optional )

Basic Initial Set Button, Anti-flicker, Dual Stream, Heartbeat, Password

Installation Manual of Network Dome Camera

Protection, Watermark

Interface

Audio Input 1 channel microphone input, 3.5mm mini-jack

Audio Output 1 channel 3.5mm audio interface (Line level, 600Ω)

Communication Interface

1 RJ45 10M / 100M self-adaptive Ethernet interface, 1 RS-485 interface

Alarm Input 2 channel

Alarm Output 2 channel

Video Output 1Vp-p Composite Output (75Ω/RCA)

General

Operating Condition

-10 ~60 (14°F~140°F), Humidity 90% or less(non℃℃ -condensing)

Power Supply DC12V±10% / PoE (AC24V optional)

Power Consumption

4.5W MAX

-I: 6W MAX(6.5W MAX with ICR working)

Impact Protection IEC60068-2-75Eh,50J;EN50102, up to IK10

IR Range -I: Within 10-20 meters (32.8-65.6ft)

Dimensions(mm) φ140 × 114 (φ5.5" × 4.9")

Weight

1400g (3.08lbs)

*”I” series supports 10-20 meters (32.8-65.6ft) IR Range

Dimensions

Installation Manual of Network Dome Camera

First Choice for Security Professionals

HIKVISION DS-2CD763PF-E, DS-2CD763PF-EI, DS-2CD763PFNF-EI, DS-2CD763PFNF-E, DS-2CD753F-E Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual