DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
DS-2CC12D8T-AMM
“Casino” D8T Box Camera
UM DS-2CC12D8T-AMM 110118NA
User Manual
1
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
Disclaimer
Copyright © 2018 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, and graphs are the
properties of Hangzhou Hikvision Digital Technology Co., Ltd., or its subsidiaries
(hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the
Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by
any means, without the prior written permission of Hikvision. Unless otherwise stipulated,
Hikvision does not make any warranties, guarantees, or representations, express or
implied, regarding the Manual.
Introduction
Thank you for purchasing our product. If there are any questions or requests, do not
hesitate to contact the dealer.
This manual may contain technically incorrect information or printing errors, and the
content is subject to change without notice. This manual will be updated as needed. We
will readily improve or update the products or procedures described in the manual.
Regulatory Information
FCC Information
Please take attention that changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
UM DS-2CC12D8T-AMM 110118NA
2
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
• Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and, if applicable, the supplied accessories too are marked with “CE”
and comply therefore with the applicable harmonized European standards listed
under the Low Voltage Directive 2014/35/EU, the EMC Directive 2014/30/EU, the
RoHS Directive 2011/65/EU.
2012/19/EU (WEEE Directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.
2006/66/EC (Battery Directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your supplier or to a
designated collection point. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions.”
UM DS-2CC12D8T-AMM 110118NA
3
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Warnings
Follow these safeguards to prevent
serious injury or death.
Cautions
Follow these precautions to prevent
potential injury or material damage.
Warnings
• In the use of the device, you must be in strict compliance with the electrical safety
regulations of the nation and region.
• Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited
Power Source with 12 VDC according to the IEC60950-1 standard. Refer to technical
specifications for detailed information.
• Do not connect multiple devices to one power adapter to avoid overheating or a fire
hazard caused by overload.
• Make sure that the plug is firmly connected to the power socket.
• Make sure that the device is firmly fixed if wall mounting or ceiling mounting is adopted.
• If smoke, odor, or noise rise from the device, turn off the power at once, unplug the
power cord, then contact the service center.
• Never attempt to disassemble the camera by unprofessional personal.
Cautions
• Do not drop the camera or subject it to physical shock.
• Do not place the camera in extremely hot, cold (the operating temperature shall be -40°
to 60° C), dusty, or damp locations, and do not expose it to high electromagnetic
radiation.
• Do not touch sensor modules with fingers.
• If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently.
• Do not aim the camera at the sun or extra bright places.
UM DS-2CC12D8T-AMM 110118NA
4
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
• The sensor may be burned out by a laser beam, so if any laser equipment is in use, make
sure that the sensor surface will not be exposed to the laser beam.
• Do not expose the device to high electromagnetic radiation or extremely hot, cold, dusty,
or damp environments.
• To avoid heat accumulation, good ventilation is required for the operating environment.
• Keep the camera away from liquid while in use for non-waterproof device.
• While in delivery, the camera shall be packed in its original packing or similar materials.
Mark Description
Table 1 Mark Description
Mark Description
DC Voltage
AC Voltage
UM DS-2CC12D8T-AMM 110118NA
5
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
Contents
1 Introduction ............................................................................................................................. 8
1.1 Product Features ............................................................................................................. 8
1.2 Overview ........................................................................................................................... 8
2 Installation ............................................................................................................................... 9
2.1 Installation Preparation .................................................................................................. 9
2.1.1 . Before You Start .................................................................................................... 9
2.2 Installing the Lens ........................................................................................................... 9
2.2.1 Before You Start .................................................................................................... 9
3 Menu Description .................................................................................................................. 11
3.1 FORMAT ........................................................................................................................... 13
3.2 LANGUAGE ....................................................................................................................... 13
3.3 MAIN MENU ...................................................................................................................... 13
3.3.2 AE (AUTO EXPOSURE) ............................................................................................ 13
3.3.2.1 LENS ........................................................................................................ 13
3.3.2.2 SHUTTER .................................................................................................. 14
3.3.2.3 BRIGHTNESS ............................................................................................. 14
3.3.2.4 EXPOSURE MODE ...................................................................................... 14
3.3.2.5 AGC (Auto Gain Control) .......................................................................... 15
3.3.2.6 SENSE UP ................................................................................................. 15
3.3.3 WB (White Balance)............................................................................................. 15
3.3.3.1 ATW (Auto Tracking White Balance) ..................................................... 15
3.3.3.2 MWB (Manual White Balance) ................................................................ 15
3.3.4 DAY/NIGHT ............................................................................................................ 16
3.3.4.1 COLOR ...................................................................................................... 16
3.3.4.2 B/W ......................................................................................................... 16
3.3.4.3 AUTO ........................................................................................................ 16
3.3.5 VIDEO SETTING ...................................................................................................... 17
3.3.5.1 CONTRAST ................................................................................................ 17
3.3.5.2 SHARPNESS ............................................................................................. 17
3.3.5.3 COLOR GAIN .............................................................................................. 17
UM DS-2CC12D8T-AMM 110118NA
6
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
3.3.5.4 3D DNR (Digital Noise Reduction) .......................................................... 17
3.3.5.5 MIRROR .................................................................................................... 17
3.3.6 FUNC (Functions) ................................................................................................. 18
3.3.7 SAVE & EXIT .......................................................................................................... 20
UM DS-2CC12D8T-AMM 110118NA
7
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
No. Description
No. Description
1 Lens Interface
2
Lock Screw
3 Dial Switch
4
Lens Socket
5 GND 6 Power Interface
7 Video Interface
1 Introduction
1.1 Product Features
The camera is applicable for indoor conditions. The main features are as follows:
• High performance CMOS sensor
• Low illumination: 0.005 lux @ (ƒ/1.2, AGC on)
• Auto gain control
• 120 dB true WDR
• OSD menu
• Internal synchronization
1.2 Overview
Table 2 Box Camera Description
UM DS-2CC12D8T-AMM 110118NA
Figure 1, Box Camera’s Overview
8
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
2 Installation
2.1 Installation Preparation
2.1.1 Before You Start
• Make sure that the device in the package is in good condition and
all the assembly parts are included.
• Make sure that all the related equipment is powered-off during the
installation.
• Check the specification of the products for the installation
environment.
• Check whether the power supply matches your required output to
avoid damage.
• Make sure the wall is strong enough to withstand three times the
weight of the camera and the bracket.
• If the wall is concrete, insert expansion screws before installing
the camera. If the wall is wood, use self-tapping screws to secure
the camera.
• If the product does not work properly, contact your dealer or the
nearest service center. Do NOT disassemble the camera for repair
or maintenance yourself.
2.2 Installing the Lens
2.2.1 Before You Start
Lens must be purchased separately.
1. Rotate the lens clockwise onto the camera module tightly.
UM DS-2CC12D8T-AMM 110118NA
9
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
Figure 2, Installing the Lens
2. Insert the cable attached on the lens to the lens socket to finish the
lens installation.
3. Connect the corresponding power cord and video cable.
4. Power on the camera to view the image on the monitor.
NOTE: Do not remove the cable attached to the lens while power is
on.
UM DS-2CC12D8T-AMM 110118NA
10
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
3 Menu Description
Call the menu by clicking the icon on the PTZ Control interface, or call preset no.95.
1. Connect the camera to the TVI DVR and the monitor, as shown below.
Figure 3, Connection
2. Power on the analog camera, TVI DVR, and the monitor to view the image on the
monitor.
3. Click PTZ Control to enter the PTZ Control interface.
4. Call the camera menu by clicking the icon, or call preset no. 95.
UM DS-2CC12D8T-AMM 110118NA
11
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
LENS
SHUTTER
BRIGHTNESS
FORMAT
MAIN MENU
AE
WB
DAY/NIGHT
VIDEO
SETTINGS
EXPOSURE MODE
AGC
SENSE UP
MODE
RETURN
MODE
RETURN
CONTRAST
SHARPNESS
COLOR GAIN
3D DNR
FUNC
LANGUAGE
RESET
SAVE & EXIT
Figure 4, Main Menu Overview
5. Click the direction arrow to control the camera.
(1) Click the Up/Down direction button to select the item.
MIRROR
RETURN
PRIVACY
MOTION
CAM ID
RETURN
UM DS-2CC12D8T-AMM 110118NA
12
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
(2) Click Iris+ to confirm the selection.
(3) Click the left/right direction button to adjust the value of the selected item.
3.1 FORMAT
PAL (Phase Alternating Lines)
PAL is a color encoding system for analog televisions used in broadcast television
systems in most countries.
NTSC: (National Television System Committee)
NTSC is the analog television system that is used in most of North America, parts
of South America, Myanmar, South Korea, etc.
3.2 LANGUAGE
Supports English and Chinese.
3.3 MAIN MENU
3.3.2 AE (AUTO EXPOSURE)
Auto Exposure describes the brightness-related parameters, which
can be adjusted by LENS, SHUTTER, BRIGHTNESS, EXPOSURE MODE, AGC,
and SENSE UP.
3.3.2.1 LENS
UM DS-2CC12D8T-AMM 110118NA
Figure 5, AE
MANUAL and DC modes are selectable.
• MANUAL: You can control the iris manually.
13
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
• DC: Iris is automatically controlled.
3.3.2.2 SHUTTER
Shutter denotes the speed of the shutter.
• Under LENS MANUAL Mode – Only AUTO is available, which
means the shutter speed is controlled automatically.
• Under LENS DC Mode
> PAL: 1/25 s, 1/50 s, FLK 1/200 s 1/400 s, 1/1K s, 1/2K s,
1/10K s, and 1/50K s are available.
> NTSC: 1/30 s, 1/60 s, FLK, 1/240s, 1/480 s, 1/1K s, 1/2K
s, 1/10K s, and 1/50K s are available.
3.3.2.3 BRIGHTNESS
Brightness refers to the brightness of the image.
You can set the brightness value from 1 to 10 to darken or
brighten the image. The higher the value, the brighter the
image.
3.3.2.4 EXPOSURE MODE
You can set the EXPOSURE MODE to GLOBAL, BLC, or WDR.
• GLOBAL
GLOBAL refers to the normal exposure mode, which adjusts
lighting distribution, variations, and non-standard
processing.
• BLC (Backlight Compensation)
BLC compensates light to the object in the front to make it
clear, but may cause overexposure of the background where
the light is strong.
UM DS-2CC12D8T-AMM 110118NA
When BLC is selected as the exposure mode, the BLC level
can be adjusted from 0 to 8.
• WDR (Wide Dynamic Range)
WDR helps the camera provide clear images even under
14
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
backlit circumstances. WDR balances the brightness level of
the whole image and provides clear images with details.
3.3.2.5 AGC (Auto Gain Control)
AGC optimizes the clarity of the image in poor light conditions.
The GAIN level can be set to HIGH, MIDDLE, or LOW. Select OFF to
disable the GAIN function.
NOTE: The noise will be amplified when the GAIN is on.
3.3.2.6 SENSE UP
Sense Up increases the exposure on a signal frame, which
makes a camera more sensitive to light, so it can produce
images even in low lux conditions. You can set the SENS-UP to
OFF or AUTO, according to the light conditions.
The SENS-UP function will automatically adjust itself to x2, x4,
x6, x8, x10, x12, x14, and x16 according to the light conditions.
3.3.3 WB (White Balance)
WB, the white rendition function of the camera, is to adjust the color
temperature according to the environment. It can remove unrealistic
color casts in the image. You can set WB mode to ATW or MWB.
3.3.3.1 ATW (Auto Tracking White Balance)
Under ATW mode, white balance is adjusted automatically
according to the color temperature of the scene illumination.
3.3.3.2 MWB (Manual White Balance)
You can set the R GAIN/B GAIN value from 1 to 255 to adjust the
image red/blue shades.
UM DS-2CC12D8T-AMM 110118NA
15
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
3.3.4 DAY/NIGHT
Color, BW (Black and White), and AUTO are selectable for DAY/NIGHT
switches.
Figure 6, MWB Mode
Figure 7, Day/Night
3.3.4.1 COLOR
The image is in color in day mode all the time.
3.3.4.2 B/W
The image is black and white all the time.
3.3.4.3 AUTO
Automatically switches between Color and BW (Black and
White) according to actual scene brightness.
UM DS-2CC12D8T-AMM 110118NA
16
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
3.3.5 VIDEO SETTING
Move the cursor to VIDEO SETTING and click Iris+ to enter the
submenu. CONTRAST, SHARPNESS, COLOR GAIN, 3D DNR, and MIRROR
are adjustable.
Figure 8, Video Setting
3.3.5.1 CONTRAST
This feature enhances the difference in color and light between
parts of an image. You can set the CONTRAST value from 1 to 10.
3.3.5.2 SHARPNESS
Sharpness determines the amount of detail an imaging system
can reproduce. You can set the SHARPNESS value from 1 to 10.
3.3.5.3 COLOR GAIN
Adjust this feature to change the saturation of the color. The
value ranges from 1 to 10.
3.3.5.4 3D DNR (Digital Noise Reduction)
3.3.5.5 MIRROR
UM DS-2CC12D8T-AMM 110118NA
The 3D DNR function can decrease the noise effect, especially
when capturing moving images in poor light conditions and
delivering more accurate and sharp image quality. You can set
the DNR value from 1 to 10.
DEFAULT, H, V, and HV are selectable for mirror.
17
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
• DEFAULT: The mirror function is disabled.
• H: The image flips 180° horizontally.
• V: The image flips 180° vertically.
• HV: The image flips 180° both horizontally and vertically.
3.3.6 FUNC (Functions)
In the FUNC sub-menu, you can set the camera’s privacy mask,
motion detection, camera ID, and DPC.
• PRIVACY
The privacy mask allows you to cover certain areas that you don’t
want to be viewed or recorded. Up to four privacy areas are
configurable.
Select a PRIVACY area. Set the DISPLAY status as ON. Click the
Up/Down/Left/Down button to define the area’s position and size.
• MOTION
In the user-defined motion detection surveillance area, the
moving object can be detected and the alarm will be triggered. Up
to four motion detection areas can be configured.
UM DS-2CC12D8T-AMM 110118NA
Figure 9, Privacy
18
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
Select a MOTION area. Set the DISPLAY status as ON. Click the
Up/Down/Left/Right button to define the position and size of the
area. Set the SENSITIVITY from 0 to 100.
Figure 10, Motion
• CAMERA ID
Edit the camera ID in this section.
Figure 11, Cam ID Setting
Set the MODE to ON. Click the Up/Down/Left/Right button to
choose the camera ID and the position.
• DPC (Defective Pixel Correction)
Defective pixels are pixels in a CMOS image sensor that fail to
sense light levels correctly. This series of camera supports
defective pixel correction.
Set mode ON to enable and OFF to disable the function.
UM DS-2CC12D8T-AMM 110118NA
19
DS-2CC12D8T-AMM “Casino” D8T Box Camera User Manual
• RESET
Reset all the settings to the defaults.
3.3.7 SAVE & EXIT
Move the cursor to SAVE & EXIT and click Iris+ to save the setting and
exit the menu.
UM DS-2CC12D8T-AMM 110118NA
20
Loading...