HIKVISION DS-2CC102P, DS-2CC102PN-A, DS-2CC102PN, DS-2CC112P, DS-2CC112PN-A User Manual

1

User Manual of Color Camera

Version 2.1

Thank you for purchasing our product. If there is any question or request, please do not feel hesitated to
contact us.

This manual may contain several technically incorrect places or printing errors, and the content is subject
to change without notice. The updates will be added into the new version of this manual. We will readily
improve or update the products or procedures described in the manual.

2

Security Awareness

This manual contains several guidelines for all customers’ demand. Please read it carefully before
operating to ensure that you can use this product correctly and safely，and to avoid the danger or material
damage which may cause otherwise. Please preserve it well for future reference.
The precaution measure is divided into “Warnings” and “Cautions” as below:
Warnings: Serious injury or death may cause if any of the warnings is neglected.
Cautions: Injury or equipment damage may cause if any of the cautions is neglected.

Warnings Follow these safeguards to
prevent serious injury or death.

Cautions Follow these precautions to
prevent potential injury or material
damage.

Warnings：

1. Input voltage should meet both the SELV(Safety Extra Low Voltage) and the Limited Power Source

with AC 24V or DC 12V according to the IEC60950－1 standard. Please refer to technical
specifications for detail information.

2. If the product does not work properly, please contact your dealer or the nearest service center. Never

attempt to disassemble the camera yourself. Users are responsible for any problem caused by
modifying or repairing without authorization.

3. The operating environment shall be away from rain or moisture to lower the danger of fire or shock

hazard.

4. The camera should be installed by qualified technicians, and comply with local laws and regulations.

5. Precautions for short circuit are required for installing.

6. Instructions for installation on walls: Please make sure that the camera can endure at least 50 Newton

(N)’s pulling downward.

3

Cautions：

1. Make sure the power supply voltage is correct before using the camera.

2. Do not drop the camera or subject it to physical shock.

3. Do not touch CCD (Charge Coupled Device) modules with fingers. If cleaning is necessary, use clean

cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period,
please turn on the lens cap to protect the CCD from dirt.

4. Do not aim the camera at the sun or extra bright places. A blooming or smear may occur otherwise

(which is not a malfunction however), and affecting the endurance of CCD at the same time.

5. The CCD may be burned out by a laser beam, so when any laser equipment is on using, make sure

that the surface of CCD will not be exposed to the laser beam.

6. Do not place the camera in extremely hot, cold(the operating temperature shall be－10℃～＋60℃ ),

dusty or damp locations, and do not expose it to high electromagnetism radiation.

7. To avoid heat accumulation, good ventilation is required for operating environment.

8. Keep the camera away from liquid while on using.

9. While on a delivery, the camera shall be packed in its original packing, or packing of the same

texture.

10. Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment shall be replaced

regularly according to their average enduring time. The average time varies because of differences
between operating environment and using history, so regular checking is recommended for all the
users. Please contact with your dealer for more details.

4

Index

Chapter 1 Brief Introduction ............................................................................................................................................ 5

1.1 Introduction ....................................................................................................................................................... 5

1.2 Introduction to the Camera Appearance ............................................................................................................ 5

1.3 Side Elevation of the Camera ............................................................................................................................ 6

1.4 Introduction to the Rear Panel of the Camera ................................................................................................... 7

Chapter 2 Installation ............................................................................................................................................................ 9

2.1 Rear Panel .......................................................................................................................................................... 9

2.2 Power Supply ..................................................................................................................................................... 9

Chapter 3 Specification ....................................................................................................................................................... 10

Table 1 ......................................................................................................................................................................... 10

Table 2 ......................................................................................................................................................................... 11

Table 3 ......................................................................................................................................................................... 12

Table 4 ......................................................................................................................................................................... 13

Table 5 ......................................................................................................................................................................... 14

5

Chapter 1 Brief Introduction

1.1 Introduction

This color camera with advanced circuit designing incorporates a CCD module that offers high sensitivity.
It is ideal for surveillance and video processing systems, and provides excellent performances such as
high resolution, low distortion and low noise, etc.

The camera incorporates extraordinary features as below: Compact Structure Design

 1/3 Inch SONY CCD
 Day / Night with Auto Switch
 Auto White Balance, Auto Gain Control, Electronic Shutter Control, and Backlight Compensation
 Flickerless Mode
 Digital Signal Processing
 Auto Iris with DC / Video Driver
 CS Mount Lens (Provide Optional Adapter for C Mount Lens)
 Internal Synchronization
 Advanced 3-axis mechanical design enables the camera to meet the installation requirement from

different environment by flexibly adjusting the lens into the require angle (Only DS-2CC511/591P-A
Support)

 Advanced double board design enables heat dissipation and quality of the images

1.2 Introduction to the Camera Appearance

To open the dome cover, put one of your hands on the pedestal to stabilize it, and rotate the side cover in
anticlockwise direction with the other hand.

Dome cover

Core

Pedestal

Figure 1

Side Cover