HIKOKI DS 12DJ, DV 12DJ, WH 12DJ Handling Instructions Manual

Download

Page 1

DS 12DJ • DV 12DJ

DS12DJ DV12DJ

Handling instructions

Page 2

1 2

3 4

DV12DJ

Min.

Max.

DS12DJ DV12DJ

Min.

Max.

Page 3

DS12DJ DV12DJ

7 8

DV12DJ

9 10

Page 4

11 12

13 14

)

-1

(

Hs 1400 min Ls 350 min

Page 5

GENERAL POWER TOOL SAFETY WARNINGS

WARNING Read all safety warnings, instructions, illustrations and speciﬁ cations provided with this power tool.

Failure to follow all instructions listed below may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or medication.

A moment of inattention while operating power tools

may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as a dust mask, non-skid

safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your ﬁ nger on the switch

or energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from moving parts.

Loose clothes, jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from frequent use

of tools allow you to become complacent and ignore tool safety principles.

A careless action can cause severe injury within a

fraction of a second.

4) Power tool use and care a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and safer

at the rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts, breakage of parts and any other condition that may aﬀ ect the power toolʼs operation. If damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.

Use of the power tool for operations diﬀ erent from

those intended could result in a hazardous situation.

Page 6

h) Keep handles and grasping surfaces dry, clean

and free from oil and grease.

Slippery handles and grasping surfaces do not

allow for safe handling and control of the tool in unexpected situations.

5) Battery tool use and care a) Recharge only with the charger speciﬁ ed by the

manufacturer.

A charger that is suitable for one type of battery pack

may create a risk of ﬁ re when used with another battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact accidentally occurs, ﬂ ush with water. If liquid contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or

burns.

e) Do not use a battery pack or tool that is damaged

or modiﬁ ed.

Damaged or modiﬁ ed batteries may exhibit

unpredictable behaviour resulting in ﬁ re, explosion or risk of injury.

f) Do not expose a battery pack or tool to ﬁ re or

excessive temperature.

Exposure to ﬁ re or temperature above 130°C may

cause explosion.

g) Follow all charging instructions and do not

charge the battery pack or tool outside the temperature range speciﬁ ed in the instructions.

Charging improperly or at temperatures outside

the speciﬁ ed range may damage the battery and increase the risk of ﬁ re.

6) Service a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

b) Never service damaged battery packs.

Service of battery packs should only be performed

by the manufacturer or authorized service providers.

PRECAUTION Keep children and inﬁ rm persons away. When not in use, tools should be stored out of reach of children and inﬁ rm persons.

CORDLESS DRIVER DRILL / COMBI DRILL SAFETY WARNINGS

1. Wear ear protectors when impact drilling.

Exposure to noise can cause hearing loss.

1. Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

2. Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fastener may contact hidden wiring.

Cutting accessory and fasteners contacting a "live" wire

may make exposed metal parts of the power tool "live" and could give the operator an electric shock.

ADDITIONAL SAFETY WARNINGS

1. Make sure that the area to be drilled is absolutely free of any hidden obstructions including electrical wiring, water, or gas pipes. Drilling into the aforementioned may result in electric shock or short circuit, gas leak or other hazards that can cause serious accidents or injuries.

2. Make sure to securely hold the tool during operation. Failure to do so can result in accidents or injuries. (Fig. 1)

3. Secure the workpiece. A workpiece clamped with clamping devices or vice is held more secure than by hand.

4. Setting up and checking the work environment. Check if the work environment is suitable by following the precaution.

5. Do not allow foreign matter to enter the hole for connecting the rechargeable battery.

6. Never disassemble the rechargeable battery and charger.

7. Never short-circuit the rechargeable battery. Shortcircuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery.

8. Do not dispose of the battery in ﬁ re. If the battery is burnt, it may explode.

9. Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted battery.

10. Do not insert object into the air ventilation slots of the charger. Inserting metal objects or inﬂ ammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger.

11. When mounting a bit into the keyless chuck, tighten the sleeve adequately. If the sleeve is not tight, the bit may slip or fall out, causing injury.

12. When changing the rotational speed with the shift knob, conﬁ rm that the switch is oﬀ . Changing the speed while the motor is rotating will damage the gears.

13. The clutch dial cannot be set between the numerals “1, 5, 10 … 20” or the dots. Do not use with the clutch dial numeral between “20” and the line at the middle of the drill mark. Doing so may cause damage. (DS12DJ only)

14. Always use this unit with clockwise rotation, when using it as impact drill. (DV12DJ only)

15. Resting the unit after continuous work.

16. The power tool is equipped with a temperature protection circuit to protect the motor and the parts that control the driving of the motor. Continuous work may cause the temperature of the unit to rise, activating the temperature protection circuit and automatically stopping operation. If this happens, allow the power tool to cool before resuming use.

17. The motor may stop in the event the tool is overloaded. In this should occur, release the tool’s switch and eliminate the cause of the overload.

18. The motor rotation may be locked to cease while the unit is used as drill. While operating the driver drill, take care not to lock the motor.

19. If motor is locked, immediately turn the power oﬀ . If the motor is locked for a while, the motor or battery may be burnt.

20. The use of the battery in a cold condition (below 0 degree Centigrade) can sometimes result in the weakened tightening torque and reduced amount of work. This, however, is a temporary phenomenon, and returns to normal when the battery warms up.

Page 7

21. Install securely the hook. Unless the hook is securely installed, it may cause an injury while using.

When electing to carry the tool hooked to your hip belt,

make sure to detach the tool bit. Failure to do so may result in unexpected injury.

22. Do not look directly into the light. Such actions could result in eye injury.

Wipe oﬀ any dirt or grime attached to the lens of the LED

light with a soft cloth, being careful not to scratch the lens.

Scratches on the lens of the LED light can result in

decreased brightness.

23. Do not use the product if the tool or the battery terminals (battery mount) are deformed.

Installing the battery could cause a short circuit that

could result in smoke emission or ignition.

24. Keep the tool’s terminals (battery mount) free of swarf and dust.

○ Prior to use, make sure that swarf and dust have not

collected in the area of the terminals.

○ During use, try to avoid swarf or dust on the tool from

falling on the battery.

○ When suspending operation or after use, do not leave

the tool in an area where it may be exposed to falling swarf or dust.

Doing so could cause a short circuit that could result in

smoke emission or ignition.

25. Always use the tool and the battery at temperatures between -5°C and 40°C.

26. Always charge the battery at an ambient temperature of 0 - 40 °C.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the protection function to stop the output. In the cases of 1 to 3 described below, when using this product, even if you are pulling the switch, the motor may stop. This is not the trouble but the result of protection function.

1. When the battery power remaining runs out, the motor stops.

In such a case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this case, release the switch of tool and eliminate causes of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and caution.

WARNING

In order to prevent any battery leakage, heat generation, smoke emission, explosion and ignition beforehand, please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the battery.

○ During work make sure that swarf and dust do not fall on

the battery.

○ Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○ Do not store an unused battery in a location exposed to

swarf and dust.

○ Before storing a battery, remove any swarf and dust that

may adhere to it and do not store it together with metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a nail, strike with a hammer, step on, throw or subject the battery to severe physical shock.

3. Do not use an apparently damaged or deformed battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or car cigarette lighter sockets.

6. Do not use the battery for a purpose other than those speciﬁ ed.

7. If the battery charging fails to complete even when a speciﬁ ed recharging time has elapsed, immediately stop further recharging.

8. Do not put or subject the battery to high temperatures or high pressure such as into a microwave oven, dryer, or high pressure container.

9. Keep away from ﬁ re immediately when leakage or foul odor are detected.

10. Do not use in a location where strong static electricity generates.

11. If there is battery leakage, foul odor, heat generated, discolored or deformed, or in any way appears abnormal during use, recharging or storage, immediately remove it from the equipment or battery charger, and stop use.

12. Do not immerse the battery or allow any ﬂ uids to ﬂ ow inside. Conductive liquid ingress, such as water, can cause damage resulting in ﬁ re or explosion. Store your battery in a cool, dry place, away from combustible and ﬂ ammable items. Corrosive gas atmospheres must be avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes, do not rub your eyes and wash them well with fresh clean water such as tap water and contact a doctor immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor, deformation, and/or other irregularities when using the battery for the ﬁ rst time, do not use and return it to your supplier or vendor.

WARNING

If a conductive foreign matter enters in the terminal of lithium ion battery, the battery may be shorted, causing ﬁ re. When storing the lithium ion battery, obey surely the rules of following contents. ○ Do not place conductive debris, nail and wires such as

iron wire and copper wire in the storage case.

○ To prevent shorting from occurring, load the battery in

the tool or insert securely the battery cover for storing until the ventilator is not seen.

REGARDING LITHIUM-ION BATTERY TRANSPORTATION

When transporting a lithium-ion battery, please observe the following precautions.

WARNING

Notify the transporting company that a package contains a lithium-ion battery, inform the company of its power output and follow the instructions of the transportation company when arranging transport. ○ Lithium-ion batteries that exceed a power output of

100Wh are considered to be in the freight classiﬁ cation of Dangerous Goods and will require special application procedures.

○ For transportation abroad, you must comply with

international law and the rules and regulations of the destination country.

Power Output

2 to 3 digit number

Page 8

NAMES OF PARTS (Fig. 1 – Fig. 14)

Rechargeable battery

Latch

Handle

Pilot lamp

Triangle mark

Mode-switching dial

Screw-tightening

mark Drill mark

Hammer mark

Clutch dial

Shift knob

Trigger switch

Sleeve

Push button

Hook (sold separately)

Screw

Groove

Display panel

Remaining battery

(

indicator switch Remaining battery

)

indicator lamp

SYMBOLS

WARNING The following show symbols used for the machine.

Be sure that you understand their meaning before use.

DS12DJ: Cordless Driver Drill DV12DJ: Cordless Combi Drill

To reduce the risk of injury, user must read instruction manual.

Only for EU countries Do not dispose of electric tools together with household waste material! In observance of European Directive 2012/19/ EU on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

Direct current

V Rated voltage

No-load speed

min-1Oscillation per minute Bpm Impact rate

Ls Low speed

Hs High speed

Brick

Wood

Metal

Machine screw

Wood screw

Drill chuck capacity

Weight*

(According to EPTA-Procedure 01/2014)

Screw – Tightening

Drilling

Impact drilling

Switching ON

Switching OFF

Disconnect the battery

Change rotation speed - High speed

Change rotation speed - Low speed

Clockwise rotation

Counterclockwise rotation

* Depending on attached battery. The heaviest weight is

measured with BSL1240M (sold separately).

Battery

Lights ; The battery remaining power is over 75%

Lights ; The battery remaining power is 50% – 75%.

Lights ; The battery remaining power is 25% – 50%.

Lights ; The battery remaining power is less than 25%

Blinks ; The battery remaining power is nearly empty. Recharge the battery soonest possible.

Blinks ; Output suspended due to high temperature. Remove the battery from the tool and allow it to fully cool down.

Blinks ; Output suspended due to failure or malfunction. The problem may be the battery so please contact your dealer.

NOTE

To prevent the battery power consumption caused by forgetting to turn oﬀ the LED light, the light goes oﬀ automatically in about 3 seconds.

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the accessories listed on page 13.

Standard accessories are subject to change without notice.

Page 9

APPLICATIONS

<DS12DJ> ○ Driving and removing of machine screws, wood screws,

tapping screws, etc.

○ Drilling of various metals ○ Drilling of various woods

○ Drilling of brick and concrete block, etc. ○ Driving and removing of machine screws, wood screws,

tapping screws, etc.

○ Drilling of various metals ○ Drilling of various woods

SPECIFICATIONS

The speciﬁ cations of this machine are listed in the Table on page 12.

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to change without prior notice.

Table 1

Indications of the pilot lamp

Before charging Blinks

Lights for 0.5 seconds. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds)

CHARGING

Before using the power tool, charge the battery as follows.

1. Connect the charger’s power cord to the receptacle.

When connecting the plug of the charger to a receptacle,

the pilot lamp will blink in red (At 1- second intervals).

2. Insert the battery into the charger.

Firmly insert the battery into the charger as shown in

Fig. 3 (on page 2).

3. Charging

When inserting a battery in the charger, charging will

commence and the pilot lamp will light continuously in red.

When the battery becomes fully recharged, the pilot lamp

will blink in red. (At 1-second intervals) (See Table 1)

● Pilot lamp indication

The indications of the pilot lamp will be as shown in

Table 1, according to the condition of the charger or the rechargeable battery.

While charging Lights

1.5 Ah

2.5 Ah

4.0 Ah

Charging complete

Overheat standby

Charging impossible

Pilot lamp (red)

● Regarding the temperatures and charging time of the battery.

The temperatures and charging time will become as

shown in Table 2.

Battery Charging voltage V 10.8 – 12 Peak Type of battery Li-ion Temperatures at which the

battery can be recharged Charging time for battery

capacity, approx.(At 20°C)

NOTE

The recharging time may vary according to the ambient

temperature and power source voltage.

In addition, the charge time becomes signiﬁ cantly long in

a low temperature environment, but this is not abnormal.

Table 2

Charger

min. min. min.

Blinks

Flickers

Lights continuously

Lights for 0.5 seconds. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds)

Lights for 1 second. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds)

Lights for 0.1 seconds. Does not light for

0.1 seconds. (oﬀ for 0.1 seconds)

UC12SL

0°C – 50°C

22 (3

cells cells cells

) ) )

37 (3 60 (3

Battery overheated. Unable to charge. (Charging will commence when battery cools)

Malfunction in the battery or the charger

CAUTION

When the battery charger has been continuously used,

the battery charger will be heated, thus constituting the cause of the failures. Once the charging has been completed, give 15 minutes rest until the next charging.

4. Disconnect the charger’s power cord from the receptacle.

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

CAUTION

○ If the battery is charged while it is heated because it has

been left for a long time in a location subject to direct sunlight or because the battery has just been used, the pilot lamp of the charger lights for 1 second, does not light for 0.5 seconds (oﬀ for 0.5 seconds). In such a case, ﬁ rst let the battery cool, then start charging.

○ When the pilot lamp ﬂ ickers (at 0.2-second intervals),

check for and take out any foreign objects in the charger’s battery connector. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Take it to your authorized Service Center.

Page 10

○ Since the built-in micro computer takes about 3

seconds to conﬁ rm that the battery being charged with charger is taken out, wait for a minimum of 3 seconds before reinserting it to continue charging. If the battery is reinserted within 3 seconds, the battery may not be properly charged.

○ If the pilot lamp does not blink in red (every second)

even though the charger cord is connected to the power, it indicates that the protection circuit of the charger may be activated.

Remove the cord or plug from the power and then

connect it again after 30 seconds or so. If this does not cause the pilot lamp to blink in red (every second), please take the charger to the HiKOKI Authorized Service Center.

Selecting the drill position 6 3 Selecting the impact position 7 3 Change rotation speed 8 3 How to use the LED light 9 3 Mounting the bit 10 3 Reversing the rotational direction 11 4 Switch operation 12 4 Mounting the hook (sold separately) 13 4 Remaining battery indicator 14 4 Selecting accessories ― 14

MOUNTING AND OPERATION

Action Figure Page Removing and inserting the battery 2 2 Charging 3 2 Selecting the mode 4 2 Tightening torque adjustment 5 2

Safeguard Function LED Light Display Corrective Action

Overload Protection

Temperature Protection Allow the tool and battery to thoroughly cool. Low Voltage Protection Recharge the battery.

On 0.25 second/oﬀ 0.25 second

LED LIGHT WARNING SIGNALS

This product features functions that are designed to protect the tool itself as well as the battery. If any of the safeguard functions are triggered during operation, the LED light will blink as described in Table 3. When any of the safeguard functions are triggered, immediately remove your ﬁ nger from the switch and follow the instructions described under corrective action.

Table 3

If the operating with the shift knob set on HIGH, adjust to LOW and continue operation. Remove the cause of the overload.

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade eﬃ ciency and

cause possible motor malfunction, sharpen or replace the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water.

4. Cleaning on the outside

When the driver drill is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric solvents, gasoline or paint thinner, for they melt plastics.

5. Storage

Store the driver drill in a place in which the temperature

is less than 40°C and out of reach of children.

NOTE

Storing lithium-ion batteries. Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration, signiﬁ cantly reducing battery usage time or rendering the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each country must be observed.

Important notice on the batteries for the HiKOKI cordless power tools

Please always use one of our designated genuine batteries. We cannot guarantee the safety and performance of our cordless power tool when used with batteries other than these designated by us, or when the battery is disassembled and modiﬁ ed (such as disassembly and replacement of cells or other internal parts).

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with statutory/country speciﬁ c regulation. This guarantee does not cover defects or damage due to misuse, abuse, or normal wear and tear. In case of complaint, please send the Power Tool, undismantled, with the GUARANTEE CERTIFICATE found at the end of this Handling instruction, to a HiKOKI Authorized Service Center.

Page 11

Information concerning airborne noise and vibration

The measured values were determined according to EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level:

Measured A-weighted sound pressure level:

Uncertainty K: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined according to EN60745.

Drilling into metal: Vibration emission value Uncertainty K = 1.5 m/s

Impact drilling into concrete: Vibration emission value Uncertainty K = 1.5 m/s

The declared vibration total value has been measured in accordance with a standard test method and may be used for comparing one tool with another. It may also be used in a preliminary assessment of exposure.

WARNING

○ The vibration emission during actual use of the power

tool can diﬀ er from the declared total value depending in the ways in which the tool is used.

○ Identify safety measures to protect the operator that

are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched oﬀ and when it is running idle in addition to the trigger time).

, D < 2.5 m/s2 (DS12DJ)

(DS12DJ)

, ID = 15.0 m/s2 (DV12DJ)

(DV12DJ)

81 dB (A) (DS12DJ)

101 dB (A) (DV12DJ)

70 dB (A) (DS12DJ) 90 dB (A) (DV12DJ)

NOTE

Due to HiKOKI’s continuing program of research and development, the speciﬁ cations herein are subject to change without prior notice.

Page 12

Bpm

DS12DJ DV12DJ

V 10.8 - 12 Peak

-1

min

-1

― 0 - 5250

― 0 - 21000

0 - 350

0 - 1400

mm ― 8

mm 29

mm 10

mm 6

mm 5.8

mm 0.8 - 10

kg 1.1 - 1.2 1.2 - 1.3

Page 13

DS12DJ DV12DJ

(2FS)

UC12SL

12― 11

BSL1225M

DS12DJ

(2FS)

DS12DJ DV12DJ

(NN)

121― 1

―――――

Page 14

BSL1215

983006

BSL1240M

UC12SL

336471

374778

374779

336642

Page 15

English Dansk Română

GUARANTEE CERTIFICATE

1 Model No. 2 Serial No. 3 Date of Purchase 4 Customer Name and Address 5 Dealer Name and Address

(Please stamp dealer name and address)

1 Modelnummer 2 Serienummer 3 Købsdato 4 Kundes navn og adresse 5 Forhandlers navn og adresse

(Indsæt stempel med forhandlers navn og

adresse)

GARANTIBEVIS

1 Model nr. 2 Nr. de serie 3 Data cumpărării 4 Numele și adresa clientului 5 Numele și adresa distribuitorului

(Vă rugăm aplicaţi ștampila cu numele și adresa

distribuitorului)

Deutsch Norsk Slovenščina

1 Modell-Nr. 2 Serien-Nr. 3 Kaufdaturn 4 Name und Anschrift des Kunden 5 Name und Anschrift des Händlers

(Bitte mit Namen und Anschrift des Handlers

GARANTIESCHEIN

abstempeln)

GARANTISERTIFIKAT

1 Modellnr. 2 Serienr. 3 Kjøpsdato 4 Kundens navn og adresse 5 Forhandlerens navn og adresse

(Vennligst stemple forhandlerens navn og adresse)

1 Št. modela 2 Serijska št. 3 Datum nakupa 4 Ime in naslov kupca 5 Ime in naslov prodajalca

(Prosimo vtisnite žig z imenom in naslovom

prodajalca)

Français Suomi Slovenčina

CERTIFICAT DE GARANTIE

1 No. de modèle 2 No de série 3 Date dʼachat 4 Nom et adresse du client 5 Nom et adresse du revendeur

(Cachet portant le nom et lʼadresse du revendeur)

1 Malli nro 2 Sarja nro 3 Ostopäivämäärä 4 Asiakkaan nimi ja osoite 5 Myyjän nimi ja osoite

(Leimaa myyjän nimi ja osoite)

TAKUUTODISTUS

1 Č. modelu 2 Sériové č. 3 Dátum zakúpenia 4 Meno a adresa zákazníka 5 Názov a adresa predajcu

(Pečiatka s názvom a adresou predajcu)

Italiano Ελληνικά Български

CERTIFICATO DI GARANZIA

1 Modello 2 N° di serie 3 Data di acquisto 4 Nome e indirizzo dellʼacquirente 5 Nome e indirizzo del rivenditore

(Si prega di apporre il timbro con questi dati)

ΠΙΣΤΟΠΟΙΗΤΙΚΟ ΕΓΓΥΗΣΗΣ

1 Αρ. Μοντέλου 2 Αύξων Αρ. 3 Ημερομηνία αγοράς 4 Όνομα και διεύθυνση πελάτη 5 Όνομα και διεύθυνση μεταπωλητή

(Παρακαλούμε να χρησιμοποιηθεί σφραγίδα)

1 Модел № 2 Сериен № 3 Дата за закупуване 4 Име и адрес на клиента 5 Име и адрес на търговеца

(Моля, отпечатайте името и адрес на дилъра)

Nederlands Polski Srpski

1 Modelnummer 2 Serienummer 3 Datum van aankoop 4 Naam en adres van de gebruiker 5 Naam en adres van de handelaar

(Stempel a.u.b. naam en adres vande de

GARANTIEBEWIJS

handelaar)

1 Model 2 Numer seryjny 3 Data zakupu 4 Nazwa klienta i adres 5 Nazwa dealera i adres

(Pieczęć punktu sprzedaży)

GWARANCJA

1 Br. modela. 2 Serijski br. 3 Datum kupovine 4 Ime i adresa kupca 5 Ime i adresa prodavca

(Molimo da stavite pečat na ime i adresu trgovca)

Español Magyar Hrvatski

CERTIFICADO DE GARANTÍA

1 Número de modelo 2 Número de serie 3 Fecha de adquisición 4 Nombre y dirección del cliente 5 Nombre y dirección del distribudor

(Se ruega poner el sello del distribudor con su

nombre y dirección)

GARANCIA BIZONYLAT

1 Típusszám 2 Sorozatszám 3 A vásárlás dátuma 4 A Vásárló neve és címe 5 A Kereskedő neve és címe

(Kérjük ide elhelyezni a Kereskedő nevének és

címének pecsétjét)

1 Br modela. 2 Serijski br. 3 Datum kupnje 4 Ime i adresa kupca 5 Ime i adresa trgovca

(Molimo stavite pečat na ime i adresu trgovca)

Português Čeština

CERTIFICADO DE GARANTIA

1 Número do modelo 2 Número do série 3 Data de compra 4 Nome e morada do cliente 5 Nome e morada do distribuidor

(Por favor, carímbe o nome e morada do

distribuidor)

1 Model č. 2 Série č. 3 Datum nákupu 4 Jméno a adresa zákazníka 5 Jméno a adresa prodejce

(Prosíme o razítko se jménem a adresou prodejce)

ZÁRUČNÍ LIST

Svenska Türkçe

GARANTICERTIFIKAT

1 Modellnr 2 Serienr 3 Inköpsdatum 4 Kundens namn och adress 5 Försäljarens namn och adress

(Stämpla försäljarens namn och adress)

GARANTİ SERTİFİKASI

1 Model No. 2 Seri No. 3 Satın Alma Tarihi 4 Müşteri Adı ve Adresi 5 Bayi Adı ve Adresi

(Lütfen bayi adını ve adresini kaşe olarak basın)

CERTIFICAT DE GARANŢIE

GARANCIJSKO POTRDILO

ZÁRUČNÝ LISTA

ГАРАНЦИОНЕН СЕРТИФИКАТ

GARANTNI SERTIFIKAT

JAMSTVENI CERTIFIKAT

Page 16

Page 17

Hikoki Power Tools Deutschland GmbH

Siemensring 34, 47877 willich, Germany Tel: +49 2154 49930 Fax: +49 2154 499350 URL: http://www.hikoki-powertools.de

Hikoki Power Tools Norway AS

Kjeller Vest 7, N-2007 Kjeller, Norway Tel: (+47) 6692 6600 Fax: (+47) 6692 6650 URL: http://www.hikoki-powertools.no

Hikoki Power Tools Netherlands B.V.

Brabanthaven 11, 3433 PJ Nieuwegein, The Netherlands Tel: +31 30 6084040 Fax: +31 30 6067266 URL: http://www.hikoki-powertools.nl

Hikoki Power Tools (U.K.) Ltd.

Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ, United Kingdom Tel: +44 1908 660663 Fax: +44 1908 606642 URL: http://www.hikoki-powertools.uk

Hikoki Power Tools France S.A.S.

Parc de l’Eglantier 22, rue des Cerisiers, Lisses-C.E. 1541, 91015 EVRY CEDEX, France Tel: +33 1 69474949 Fax: +33 1 60861416 URL: http://www.hikoki-powertools.fr

Hikoki Power Tools Belgium N.V./S.A.

Koningin Astridlaan 51, B-1780 Wemmel, Belgium Tel: +32 2 460 1720 Fax: +32 2 460 2542 URL http://www.hikoki-powertools.be

Hikoki Power Tools Italia S.p.A

Via Piave 35, 36077, Altavilla Vicentina (VI), Italy Tel: +39 0444 548111 Fax: +39 0444 548110 URL: http://www.hikoki-powertools.it

Hikoki Power Tools lbérica, S.A.

C/ Puigbarral, 26-28, Pol. Ind. Can Petit, 08227 Terrassa (Barcelona), Spain Tel: +34 93 735 6722 Fax: +34 93 735 7442 URL: http://www.hikoki-powertools.es

Hikoki Power Tools Österreich GmbH

IndustrieZentrum NÖ –Süd, Straße 7, Obj. 58/A6 2355 Wiener Neudorf, Austria Tel: +43 2236 64673/5 Fax: +43 2236 63373 URL: http://www.hikoki-powertools.at

Hikoki Power Tools Sweden AB

Rotebergsvagen 2B SE-192 78 Sollentuna, Sweden Tel: (+46) 8 598 999 00 Fax: (+46) 8 598 999 40 URL: http://www.hikoki-powertools.se

Hikoki Power Tools Denmark A/S

Lillebaeltsvej 90, 6715 Esbjerg N, Denmark Tel: (+45) 75 14 32 00 Fax: (+45) 75 14 36 66 URL: http://www.hikoki-powertools.dk

Hikoki Power Tools Finland Oy

Tupalankatu 9, 15680 Lahti, Finland Tel: (+358) 20 7431 530 Fax: (+358) 20 7431 531 URL: http://www.hikoki-powertools.ﬁ

Hikoki Power Tools Hungary Kft.

1106 Bogáncsvirág u.5-7, Budapest, Hungary Tel: +36 1 2643433 Fax: +36 1 2643429 URL: http://www.hikoki-powertools.hu

Hikoki Power Tools Polska Sp. z o. o.

ul. Gierdziejewskiego 1 02-495 Warszawa, Poland Tel: +48 22 863 33 78 Fax: +48 22 863 33 82 URL: http://www.hikoki-narzedzia.pl

Hikoki Power Tools Czech s.r.o.

Modřická 205, 664 48 Moravany, Czech Republic Tel: +420 547 422 660 Fax: +420 547 213 588 URL: http://www.hikoki-powertools.cz

Hikoki Power Tools Romania S.R.L.

Ring Road, No. 66, Mustang Traco Warehouses, Warehouse No.1, Pantelimon City, 077145, Ilfov County, Romania Tel: +40 371 135 109 Fax: +40 372 899 765 URL: http://www.hikoki-powertools.ro

Page 18

Page 19

Page 20

We declare under our sole responsibility that Cordless Driver Drill / Cordless Combi Drill, identiﬁ ed by type and speciﬁ c identiﬁ cation code *1), is in conformity with all relevant requirements of the directives *2) and standards *3). Technical ﬁ le at *4) – See below. The European Standard Manager at the representative oﬃ ce in Europe is authorized to compile the technical ﬁ le. The declaration is applicable to the product aﬃ xed CE marking.

*1) DS12DJ C357897R DV12DJ C357904R

*2) 2006/42/EC, 2014/30/EU, 2014/35/EU, 2011/65/EU *3) EN60745-1:2009+A11:2010

EN60745-2-1:2010 EN60745-2-2:2010

EN60335-1:2012+A11:2014 EN60335-2-29:2004+A2:2010 EN55014-1:2006+A1:2009+A2:2011 EN55014-2:1997+A1:2001+A2:2008

*4) Representative oﬃ ce in Europe

Hikoki Power Tools Deutschland GmbH

Siemensring 34, 47877 Willich, Germany

Head oﬃ ce in Japan

EC DECLARATION OF CONFORMITY

29. 12. 2018 Naoto Yamashiro European Standard Manager

29. 12. 2018

Koki Holdings Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo, Japan

A. Nakagawa Corporate Oﬃ cer

Code No. C99254311 G Printed in China

812