High Street TV Yawn Air YAB01 User Instruction

KING SIZE AIR BED

USER INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS MANUAL INFLATION AND DEFLATION

• For Indoor use only.

• Do not expose the electric pump to moisture.

• Inspect the power cord regularly. Do not use the airbed if the power cord or plug is damaged.

• Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained inside.

• Never run the pump for longer than 10 minutes at a time. Let the motor cool down for 5 minutes
before using it again. Disconnect the plug when the pump is not in use.

• Do not block air intake during operation, this could damage the motor.

• Do not let children use the electric pump.

• Do not use hot air to ll the air bed.

• Do not over inate the airbed. Stop inating once the airbed is fully expanded and rm.

• This airbed is not a buoyancy aid. Do not use it on water.

• This airbed is not a lifebuoy or life saving device.

• Keep the airbed away from re.

• This airbed is not a toy. Do not stand or jump on it. Use only as a mattress.

• Always have the ocked surface facing upright.

• Never hold the air inlet / outlet near your eyes or hair when the pump is running.

• Never let children play with the airbed.

• Make sure that the airbed is laid on a level surface free from stones and sharp objects. Bed may tip
over on uneven surfaces.

• This airbed may be used by children 8 years and older, and by persons with reduced physical, sensory
or mental capability or lack of experience and knowledge, provided they are supervised and have
been given instructions concerning use of the product in a safe way, and understand the hazards
involved.

• Avoid exposing your airbed to extreme temperature (hot or cold). In hot weather, the air will expand.
You must let out some air to prevent the airbed from failing due to overpressure. In cold weather your
airbed will lose some pressure due to the fact that the air will contract.

The airbed is pump compatible – it can be pumped manually when travelling or far away from a power

source. It can be inated with a hand pump, foot pump or bicycle pump as long as the pump ts the air
valve opening. Don’t use a compressor or any other mechanical pump. Do not over inate the airbed.

1. Remove the cap from the air valve.

2. Connect a hand pump to the air valve.

3. Inate the bed manually. Do not over inate the airbed.

4. Replace the air valve cap.

5. The air valve has 3 settings; OPEN, INLET ONLY and SEALED. Use the INLET ONLY setting to inate

the bed in small increments to adjust the rmness of the bed.

6. For manual deation, leave the air valve in the OPEN setting.

PARTS

Air

Valve

How to inate using the built-in pump.

1. Lay the bed at out on the oor free of obstructions or sharp objects. Ensure that the headboard
section is on the top when laid out. Plug the mains lead into a wall socket.

2. Turn the control knob to . Make sure the valve is closed.

3. When the airbed is sufciently inated (not hard), turn off the pump by turning the control knob
to . In ordinary operating conditions, the airbed takes approximately 3 to 4 minutes to inate.

A high pitch whine of the pump will signal the bed is inated to full (rmest) capacity. The airbed
will not over inate.

4. Pull out the mains plug and store it in its storage compartment.

Storage

Compartment

Power

Cord

Control

Knob

MAINTENANCE AND STORAGE

• Wipe clean only with a damp cloth. DO NOT use strong detergents.

• Ensure the airbed is completely DEFLATED and DRY before storage.

• Store in a cool, dry place.

• Your airbed should be stored with the valve closed.

• Keep sharp objects away from the airbed.

• In case of a puncture, a repair patch has been included. Please follow repair
instructions carefully.

How to deate using the built-in pump.

1. Plug the mains lead into a wall socket.

2. Turn the control knob to . In ordinary operating conditions, the airbed takes approximately 6

minutes to deate.

3. When the airbed is empty, turn off the pump by turning the control knob to position (OFF).

4. Pull out the mains plug and store it in its storage compartment.

Made in China.
Please read all instructions carefully and retain for future reference.
Model number: YAB01