Label Picture Description QTY
A
Left Armrest
(with Legs)
1
B
Right Armrest
(with Legs)
1
C
Backrest
(with Legs)
3
D Seat Panel 3
E
Front Panel
(with Legs)
3
Caution : You must read this before you proceed
3 Seater
Page 1 OF 11
F Left Front Foot Clip 1
G Right Front Foot Clip 1
H Left Back Foot Clip 1
I Right Back Foot Clip 1
J Front Middle Foot Clip 2
K Back Middle Foot Clip 2
L
Inner Panel
(with Legs)
2
M Seat Cushion 3
Q Rubber Hammer 1
Before
Beginning
Assembly:
Page 2 OF 11
This 3 Seater has multiple parts and may require up to 60 minutes to assemble. To give you an overview of
the 3 Seater parts, the above picture is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1
Open the carton and place all parts on a clean, non-marring surface.
Place the two Front Panels(E) facedown on the clean, non-marring surface.
Insert the Clasps of the Front Panel(E) into the large part of Pear-shaped Clasp mounting positions of the
other Front Panel(E) as shown above.
Button up the Clasps with the Rubber Hammer(Q) as pictured.
Overview
Left Armrest (A)
Seat Cushion (M)
Backrest (C)
Front Panel (E)
Front Facing
Right Armrest (B)
Seat Panel (D)
Right Front Foot Clip (G)
Left Front Foot Clip (F)
Left Back Foot Clip (H)
Front Middle Foot Clip (J)
Clasp
Pear-shaped Clasp
Mounting Position
Page 3 OF 11
Align Inner Panel(L) to Middle Panel(E) as pictured above.
Insert the Dowel of the Inner Panel into the mounting position of the Middle Panel until it clicks into place.
Repeat this process with the remaining Inner Panel(L).
Step 2
Insert the Clasps of the Front Panel(E) into the large part of Pear-shaped Clasp mounting positions of the
other Front Panel(E) as shown above.
Button up the Clasps with the Rubber Hammer(Q) as pictured.
Step 3
Dowel
Pear-shaped Clasp
Mounting Position
Clasp
Page 4 OF 11
Step 4
Place the Seat Panels(D) facedown on the clean, non-marring surface.
Insert the Clasps of the Seat Panel(D) into the large part of Pear-shaped Clasp mounting positions of the
other Seat Panel(D) and push down to button up the Clasps with the Rubber Hammer(Q).
Step 5
Insert the Clasps of the Seat Panel(D) into the large part of Pear-shaped Clasp mounting positions of the
other Seat Panel(D) and push down to button up the Clasps with the Rubber Hammer(Q).
Another side of Seat Board (D)
Page 5 OF 11
Step 6
With help from an adult partner, insert Front Panels(E) and Inner Panels(L) into Seat Panels(D) using the
interlocking joints with Rubber Hammer(Q).
Step 7
Place the Backrests(C) on the clean, non-marring surface.
Insert the Clasps of the Backrest(C) into the large part of the Pear-shaped Clasp mounting positions on the
other Backrest(C).
Button up the Clasps with the Rubber Hammer(Q) as pictured.
Page 6 OF 11
With help from an adult partner, place the Backrests(C) on the Seat Panels(D) and Inner Panels(L) as
shown above.
Insert the Clasps of the Seat Panels(D) and Inner Panels(L) into the large part of Pear-shaped Clasp
Mounting Positions of the Backrests(C).
Step 8
Insert the Clasps of the Backrest(C) into the large part of the Pear-shaped Clasp mounting positions on the
other Backrest(C).
Button up the Clasps with the Rubber Hammer(Q) as pictured.
Step 9
Page 7 OF 11
Step 10
With the help of your adult partner, stand the assembly upright.
Button up the Clasps with the Rubber Hammer(Q) left to right as pictured.
Step 11
Align the Left Armrest(A) to the left side of Backrest(C), Seat Panel(D), and Front Panel(E).
Insert the Clasps on the Left Armrest(A) into the Pear-shaped Clasp mounting positions on the Front
Panel(E), Seat Panel(D), and Backrest(C).
Insert the 8 Clasps of Front Panel(E), Seat Panel(D), and Backrest(C) into Pear-Shaped Clasp mounting
positions of Left Armrest(A).
Button up the Clasps with the Rubber Hammer(Q) from left to right as shown above.
Page 8 OF 11
Repeat the process from Step 10, to assemble the Right Armrest(B)
Step 13
Attach the Left Front Foot Clip(F), Right Front Foot Clip(G), Left Back Foot Clip(H), Right Back Foot Clip(I),
Front Middle Foot Clips(J), and Back Middle Foot Clips(K) to the feet of the 3 Seater using the Rubber
Hammer(Q) as shown above.
Step 12
Page 9 OF 11
Step 14
With the help of your adult partner, stand the 3 Seater up on a Lever surface, to check for wobbles.
If there are wobbles, use the Rubber Hammer(Q) to ensure all parts are properly secured.
Step 15
Place the Cushion(M) on the seat.
Your 3 Seater is ready for use.
This 3 Seater can only be used on a flat, level surface.
Page 10 OF 11
Page 11 OF 11
Label Picture Description QTY
N Table Top 1
O Leg 4
Caution : You must read this before you proceed
Table
Page 1 OF 4
Q Rubber Hammer 1
This Table has multiple parts and may require up to 30 minutes to assemble. To give you an overview
of the Table parts, the above picture is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and steps before assembly.
Before
Beginning
Assembly:
Overview
Leg (O)
Table Top (N)
Leg (O)
Front Facing
Page 2 OF 4
Your Table is ready for use.
This Table can only be used on a flat, level surface.
Step 1
Open the carton, and place all parts on a clean, non-marring surface.
Place the Table Top(N) facedown on the clean, non-marring surface.
Insert one Leg(O) into the mounting position on the Table Top(N), use the Rubber Hammer(Q) to
secure the Leg as shown above.
Repeat the same process with the remaining Legs(O).
Step 2
Place the Table on a level surface to check the wobbles.
If there are wobbles, use the Rubber Hammer(Q) to ensure Legs are properly secured.
Step 3
Leg Mounting Position
Page 3 OF 4
Page 4 OF 4
Label Picture Description QTY
A
Left Armrest
(with Legs)
1
B
Right Armrest
(with Legs)
1
C
Backrest
(with Legs)
1
Caution : You must read this before you proceed
Club Chair
Page 1 OF 7
D Seat Panel 1
E
Front Panel
(with Legs)
1
F Left Front Foot Clip 1
G Right Front Foot Clip 1
H Left Back Foot Clip 1
I Right Back Foot Clip 1
M Seat Cushion 1
Q Rubber Hammer 1
Before
Beginning
Assembly:
Page 2 OF 7
This Club Chair has multiple parts and may require up to 30 minutes to assemble. To give you
an overview of the Club Chair parts, the above picture is to help you put the various parts into
perspective. Please read through the instructions below to familiarise yourself with the parts and
steps before assembly.
Step 1
Open the carton and place all parts on a clean, non-marring surface.
Place the Seat Panel(D) facedown on the clean, non-marring surface.
Insert Front Panel(E) into Seat Panel(D) using the interlocking joints and secure with Rubber
Hammer(Q).
Overview
Left Armrest (A)
Seat Cushion (M)
Backrest (C)
Front Panel (E)
Front Facing
Right Armrest (B)
Seat Panel (D)
Right Front Foot Clip (G)
Left Front Foot Clip (F)
Left Back Foot Clip (H)
Front of Seat
Board(D)
Back of Seat
Board(D)
Page 3 OF 7
Turn the assembly onto it's side as shown.
Insert the Clasps on the Left Armrest(A) into the Pear-shaped Clasp mounting positions on the
Front Panel(E), Seat Panel(D), and Backrest(C).
Insert the 8 Clasps of Front Panel(E), Seat Panel(D), and Backrest(C) into Pear-Shaped Clasp
mounting positions of Left Armrest(A).
Step 2
Place the Backrest(C) upright and align Seat Panel(D) as shown above.
There are four Pear-shaped Clasp mounting positions on the Backrest(C), and four Clasps on
the Seat Panel(D).
Insert the four Clasps into four mounting positions and push down to button up the Clasps with
the Rubber Hammer(Q).
Step 3
Pear-shaped Clasp
Mounting Position
Clasp
Clasp
Pear-shaped Clasp
Mounting Position
Page 4 OF 7
Step 4
Button up the Clasps with the Rubber Hammer(Q) from left to right as shown above.
Step 5
With the help of an adult partner, turn the assembly over as shown above.
Repeat the same process from Steps 3 - 4 with the Right Armrest(B).
Page 5 OF 7
Step 6
Attach the Left Front Foot Clip(F), Right Front Foot Clip(G), Left Back Foot Clip(H), Right Back
Foot Clip(I) to the feet of the Club Chair using the Rubber Hammer(Q) as shown above.
Step 7
With the help of your adult partner, stand the Club Chair up on a Lever surface, to check for
wobbles.
If there are wobbles, use the Rubber Hammer(Q) to ensure all parts are properly secured.
Step 8
Place the Cushion(M) on the seat.
Your Club Chair is ready for use.
This Club Chair can only be used on a flat, level surface.
Page 6 OF 7
Page 7 OF 7
Loading...