INTRODUCTION
WARNINGS AND CAUTIONS
Congratulations on your purchase of ENDURO SERIES OUTDOOR WRIST
INSTRUMENT. These products represent the state-of-the-art in recreational watches.
Please keep in mind, your watch is a sensitive technical instrument. With proper care
and maintenance, it will last for many years. However, improper care and handling can
cause the various sensors to be damaged and to stop functioning.
This manual is prepared in easy-to-read sections to familiarize you with setting and
operating the watch’s functions. Please read all sections of this manual carefully and
become fully familiar with the operation of the watch before using it in the field.
Proper setup and operation will greatly enhance the watches usefulness and
your enjoyment.
english
1
WARNING: Before starting any exercise program or performing any vigorous physical
activity, we strongly suggest you visit your doctor for a complete physical and to discuss
your plans.
CAUTION: Your watch is designed to be water resistant to a static pressure of 5 ATM
and can be worn while showering and light swimming. However, we recommend that
extensive use of the unit in the water be avoided whenever possible.
CAUTION: Care should be taken not to press any keys while the unit is wet or
submerged as this can force moisture past the key seals and damage the unit.
CAUTION: Exposure to strong magnetic fields will cause the compass unit (ENDURO
COMPASS ONLY) to malfunction and may even permanently damage the compass sensor.
Keep the unit away from magnetic sources.
english
2
TABLE OF CONTENTS
TABLE OF CONTENTS
HOW TO USE THIS MANUAL 5
CARE & MAINTENANCE 6
REPLACING THE WATCH BATTERY 7
RESETTING THE WATCH 8
DISPLAY SYMBOLS AND THEIR MEANINGS 9
KEYS AND THEIR FUNCTIONS 11
MODES OF OPERATION 13
SETTING THE WATCH FUNCTIONS 14
english
EL/BACKLIGHT SYSTEM 14
VIEW TIME ZONE 1 / TIME ZONE 2 15
SETTING TIME/DATE 16
SETTING THE CHRONOGRAPH 18
SETTING THE TIMERS 19
CALIBRATING THE COMPASS 22
SETTING DAILY ALARMS 25
3
OPERATING THE WATCH 27
OPERATING THE CHRONOGRAPH 27
CHRONOGRAPH DATA REVIEW MEMORY 28
REVIEWING RUNS/WORKOUTS 29
OPERATING THE COUNTDOWN TIMERS 30
OPERATING THE COMPASS 31
FUNCTIONAL SPECIFICATIONS AND RANGES 32
TROUBLE SHOOTING BASIC 33
english
4
HOW TO USE THIS MANUAL
CARE & MAINTENANCE
Enduro watches have many unique features and functions. Be sure to read each section
carefully so that you will fully understand how the units and its features work.
The manual is divided into sections outlining each of the major functions of the watch.
A drawing of the watch screen that represents the starting point or other important
screen for each operational process is shown adjacent to the instructions for the
process; important keys are shown in color indicating
The steps for the programming or operation are adjacent to the screen illustration. Key
points and important information are shown in highlighted blocks.
The watch itself is an important part of this manual as it prompts you through its
operation.
english
5
PRESS & HOLD and PRESS.
Your Enduro watch should be protected from shocks, extreme heat and extended
exposure to direct sunlight. You should only perform service procedures related to the
changing of the battery as shown in this manual. NEVER attempt to disassemble. Store
your watch in a clean, dry area at room temperature.
Clean your watch using a moist cloth. Care should be taken when cleaning the lens not
to rub dirt into the surface as it can become scratched and hard to read.
english
6
REPLACING THE WATCH BATTERY
RESETTING THE WATCH
The Enduro watches use a common CR2032 3v Lithium battery. Normal battery life is
approximately 1yr.
NOTE: Heavy usage of the Compass or Backlight system may significantly
reduce battery life.
NOTE: A blank display or inaccurate compass readings are indications that the
battery is getting weak and should be replaced.
1. Remove battery door using a coin.
2. Carefully remove the old battery. Do not damage the O-ring
seal.
3. Place a fresh battery in the battery compartment with the
positive (+) side facing up.
4. Replace battery door using a coin.
english
5. If the O-ring has been damaged, replace it before reinstalling
the battery door. Most jewelers and watch shops should
have replacement O-ring seals.
NOTE: Extreme care should be taken when replacing the battery to ensure the
unit remains fully water resistant. Failure to properly replace the battery and
correctly seal the unit may cause the unit to become damaged and may void the
warranty
7
To reset the watch back to its default values PRESS the
MODE, SET/CLEAR, START/LAP and STOP/NEXT keys
down at the same time. The display will light up showing all
segments followed by a sequence of screens showing various
numbers. The watch will then automatically change to the time
of day screen at 12 o’clock on the first of January.
Resetting the watch will clear any information stored in the
watch. This should be done only as a last resort.
-
!
$
%
)
.
#
(
)
.
!
s
(
-
0
%
!
4
2
%
'
2
3
/
.
7
/
!
2
4
%
(
2
#
2
4
%
.
3
!
)
3
4
english
8
DISPLAY SYMBOLS AND THEIR MEANINGS DISPLAY SYMBOLS AND THEIR MEANINGS
DISPLAY SYMBOLS
symbol description what it means
"AUTO-EL" BACKLIGHT
CHRONOGRAPH
TIMER
HOURLY CHIME
ALARM ON
DEGREES
english
9
Auto-El Backlight is active when displayed
Chronograph is active when displayed
Timer is active when displayed
Hourly chime is active when displayed
Alarm is active when displayed
Compass is active when displayed (
ENDURO COMPASS ONLY)
MODE SYMBOLS
symbol description what it means
SPLIT INIDCATOR
LAP INDICATOR
CHRONO STOPPED
PM INDICATOR
AM INDICATOR
TIME ZONE 2
Displays when Chronograph is running and Lap Detail in
Chronograph memory
Displays when Chronograph is running and Lap Detail in
Chronograph memory
Displays when Chronograph is stopped
Indicates PM Time
Indicates AM Time
Indicates Time Zone 2 on display
BATTERY SYMBOLS
symbol battery status what it means
none
GOOD
MEDIUM
LOW
Battery is in good condition.
Battery is half full.
Battery needs to be replaced
english
10
KEYS AND THEIR FUNCTIONS KEYS AND THEIR FUNCTIONS
The Enduro has 5 individual keys. Each key has several functions. The drawing identifies
the keys and their names as used in this manual.
SET/CLEAR KEY
START/LAP KEY
MODE KEY
english
EL/LIGHT KEY
STOP/NEXT KEY
11
MODE KEY
- Advances display through the various
operational modes
- Selects variable in setting mode
SET / CLEAR KEY
- Enter/Exit setting sequence for each
function
- Clear Chronograph and memories
- Enter Compass Calibration sequence
(ENDURO COMPASS ONLY)
- Quick Access to Compass when operating
in Chronograph or Timer modes
(ENDURO COMPASS ONLY)
START / LAP KEY
- View/Select Time 1 / Time 2 in Time mode
- Increases variable in Setting sequence
- Start/Lap/Split action in Chronograph
mode
- Starts recall and scrolls through
information in Memory mode
- Starts Timer(s)
- Turns Daily Alarm On/Off
- Activates compass reading in Compass
(ENDURO COMPASS ONLY)
mode
- Selects Key Beep On/Off in Time setting
sequence
STOP / NEXT KEY
- Stops Chronograph
- Stores Chronograph data to memory
- Decreases variable in Setting sequence
- Advances to next data file in Review mode
- Stops Timer
- Activates compass reading in Compass
(ENDURO COMPASS ONLY)
mode
- Scrolls through Daily Alarms
- Selects Key Beep On/Off in Time setting
sequence
EL / LIGHT KEY
- Activates EL/Backlight
- Hold 3 Sec. Activates/deactivates
Automatic Backlight
english
12
MODES OF OPERATION
SETTING THE WATCH FUNCTIONS
ENDURO MAIN DISPLAY MODES
Advance through the modes below using QUICK PRESSES of the MODE key.
TIME CHRONOGRAPH REVIEW DATA
english
ALARM
13
COMPASS
(
ENDURO COMPASS ONLY)
TIMER
EL/BACKLIGHT SYSTEM
Activate the BACKLIGHT system at any time by PRESSING of
EL/LIGHT key. The backlight will remain active for a period
the
of 2 seconds.
AUTO EL/BACKLIGHT
Auto-EL mode automatically illuminates the backlight for 2
seconds whenever any key is pressed. This is convenient when
operating the watch at night or in other low light situations.
To activate/deactivate the AUTO-EL MODE,
EL/LIGHT key for 2 seconds. Auto-El status is indicated by
icon in upper center of display.
NOTE: Excessive use of the backlight system will result in shorter battery life.
PRESS & HOLD
english
14
SETTING THE WATCH FUNCTIONS
SETTING THE WATCH FUNCTIONS
VIEW TIME ZONE 1 / TIME ZONE 2
Your Enduro watch allows you to set two separate time zones.
In TIME MODE, Time Zone 2 can be viewed by a PRESSING
the START/LAP key. When viewing Time Zone 2, the display
will indicate T2 in the upper left of the display.
HOLD the START/LAP key to change primary time zone
display.
PRESS &
NOTES FOR SETTING THE WATCH
NOTE: When in setting sequence, the variable being
set will blink.
NOTE: When in setting sequence, “+” and “-” icons
are displayed whenever it is possible to increase or
english
decrease a variable that is being set.
NOTE: If no key is pressed for 60 seconds while in
setting mode, setting mode automatically exits and
changes will not be saved.
PRESS SET/CLEAR key to exit setting sequence.
NOTE:
15
SETTING TIME/DATE
1. Advance to TIME screen by PRESSING the MODE key.
PRESS & HOLD the SET/CLEAR key to enter the setting
2.
sequence.
3. Adjust HOURS by
NEXT
4. Advance to set MINUTES by
Adjust by
5. Advance to set SECONDS by
Adjust by
keys.
6. Advance to set YEAR by
PRESSING the START/LAP or STOP/NEXT keys.
by
CONTINUED NEXT PAGE)
(
PRESSING the START/LAP or STOP/
keys.
PRESSING the MODE key.
PRESSING the START/LAP or STOP/NEXT keys.
PRESSING the MODE key.
PRESSING the START/LAP or STOP/NEXT
PRESSING the MODE key. Adjust
english
16
SETTING THE WATCH FUNCTIONS SETTING THE WATCH FUNCTIONS
SETTING TIME/DATE (CONTINUED)
7. Advance to set MONTH by
8. Advance to set DAY by
9. Advance to select 12 OR 24-HOUR mode. Select by
10. Advance to set HOURLY CHIME by
11. Advance to set KEY BEEP by
english
12.
17
PRESSING the START/LAP or STOP/NEXT
Adjust by
keys.
PRESSING the START/LAP or STOP/NEXT keys.
by
PRESSING the START/LAP or STOP/NEXT keys.
MODE Key. Turn ON/OFF by PRESSING the START/LAP
STOP/NEXT keys.
or
Turn ON/OFF by
keys.
NEXT
PRESS the SET/CLEAR key to exit the setting sequence
and return to Time of Day screen.
NOTE: You can exit the setting sequence at any time by
PRESSING the SET/CLEAR key.
PRESSING the MODE key.
PRESSING the MODE key. Adjust
PRESSING the
PRESSING the MODE Key.
PRESSING the START/LAP or STOP/
SETTING THE CHRONOGRAPH
Enduro watches are equipped with a 24-hour, 100-lap Chronograph with 1/100-second
resolution. The Chronograph has 4 viewing options.
In Chronograph mode:
NOTE: If there is information in the Chronograph, you must first RESET the
Chronograph by
PRESSING the STOP/NEXT key.
1. PRESS & HOLD the SET/CLEAR key to enter the setting sequence.
2. Select VIEWING OPTION by
PRESS SET/CLEAR key to return to Chronograph mode.
3.
PRESSING the SET/CLEAR key or SAVE to memory by
PRESSING the START/LAP or STOP/NEXT keys.
english
18
SETTING THE WATCH FUNCTIONS SETTING THE WATCH FUNCTIONS
SETTING THE TIMERS
Enduro watches are equipped with 3 independent 24-hour Timers with enhanced
functionality. In TIMER MODE, you can scroll through Timers 1 through 3 by PRESSING the
STOP/NEXT key.
Timer options are:
CD-STOP: Counts down, then stops at 00:00:00.
CD-REPEAT: Counts down, then automatically starts to count down again.
CD-UP: Counts down, then automatically begins counting up. Example: you can
program a 10-minute warm up followed by a 45-minute workout. The timer counts down
10 minutes, then begins timing like a regular chronograph.
TRAIN: Trainer mode has up to 9 settable segments. The length of each segment can be
set independently. Each segment counts down to 00:00:00 and automatically advances to
the next segment which begins counting down immediately in a continuous loop.
english
19
SETTING THE TIMERS (CONTINUED)
In Timer mode:
1. Select TIMER 1, 2 or 3 by
PRESS & HOLD the SET/CLEAR key to enter the setting
2.
sequence.
3. Select TIMER MODE (CD-STOP, CD-REPEAT, CD-UP or
4. Advance to set HOURS by
5. Advance to set MINUTES by
6. Advance to set SECONDS
PRESS SET/CLEAR to exit the setting sequence.
7.
CONTINUED NEXT PAGE)
(
PRESSING the START/LAP or STOP/NEXT
TRAIN) by
keys.
PRESSING the START/LAP or STOP/NEXT keys.
Adjust by
PRESSING the START/LAP or STOP/NEXT keys.
Adjust by
PRESSING the START/LAP or STOP/NEXT keys.
Adjust by
PRESSING the STOP/NEXT key.
PRESSING the MODE key.
PRESSING the MODE key.
by PRESSING the MODE key.
english
20
SETTING THE WATCH FUNCTIONS SETTING THE WATCH FUNCTIONS
SETTING THE TIMERS (CONTINUED)
If TRAIN mode is selected:
1. Program Segment 1: Advance to set HOURS by
2. Advance to set MINUTES by
3. Advance to set SECONDS by
4. Advance to PROGRAM NEXT SEGMENT by
5.
english
21
PRESSING the START/LAP or STOP/NEXT keys.
Adjust by
START/LAP or STOP/NEXT keys.
the
the START/LAP or STOP/NEXT keys.
programming sequence (up to 9 individual segments).
PRESS SET/CLEAR to exit the setting sequence at any time.
PRESSING the MODE key. Adjust by PRESSING
PRESSING the MODE key. Adjust by PRESSING
PRESSING the MODE key.
PRESSING the MODE key. Repeat
CALIBRATING THE COMPASS (ENDURO COMPASS ONLY)
The Enduro Compass is equipped with a digital magnetic compass with reading in
one-degree increments. The compass can be adjusted to compensate for the magnetic
declination corresponding to the area where the compass is being used.
The compass must be calibrated on a regular basis. The compass should be
calibrated any time it does not seem to be working properly. We recommend calibrating
the compass prior to any activity where optimal accuracy is desired, such as a long back
country trip.
NOTE: To save power, the compass feature of the unit only remains active for
a period of 10 seconds. To reactivate the compass display, PRESS the START/
LAP or STOP/NEXT key.
(
CONTINUED NEXT PAGE)
english
22
SETTING THE WATCH FUNCTIONS SETTING THE WATCH FUNCTIONS
CALIBRATING THE COMPASS (CONTINUED)
In Compass mode:
1.
PRESS & HOLD the SET/CLEAR key to enter the calibration
sequence.
2. ROTATE CAL will appear in the center of the display. 32-
segment ring around the outside will animate clockwise to
prompt the user to rotate the watch during calibration.
3. Rotate the watch clockwise for two complete rotations of
approximately 15-seconds per rotation.
NOTE: For the optimum accuracy, the compass must be
held completely level during the calibration process. We
recommend placing the unit on top of a drinking glass
while performing the calibration as this will make it easier
to keep the compass level.
english
4. Advance to set DECLINATION by
key.
NOTE: If you do not know the Magnetic Declination for
your area, leave this setting at zero.
5. Set DECLINATION by
STOP/NEXT key for WESTERN (-).
PRESS SET/CLEAR to exit the setting sequence.
6.
23
PRESSING the MODE
PRESSING the START/LAP key for EASTERN (+) or
MAGNETIC DECLINATION
A magnetic compass points to the earth’s magnetic north pole. Depending on your
location, this may be different from True North. Adjusting the Magnetic Declination
allows you to compensate for this variation. Magnetic Declination for an area can be
found on topographical maps. Declination can change over time and distance. Make
sure the source for your declination settings is up to date. The following websites are
good sources for finding local Magnetic Declination.
FOR U.S. DECLINATIONS:
http://www.ngdc.noaa.gov/seg/geomag/jsp/Declination.jsp
FOR CANADIAN DECLINATIONS:
http://gsc.nrcan.gc.ca/geomag/field/mdcalc_e.php
english
24
SETTING THE WATCH FUNCTIONS SETTING THE WATCH FUNCTIONS
SETTING DAILY ALARMS
The Enduro watches are equipped with three individual daily alarms which can be set to
the hour and minute. Alarms are active for current Time Zone selected.
SELECTING ALARM 1, 2 OR 3
Scroll through ALARM 1, 2 or 3 (indicated in the upper line of the display) by
PRESSING the STOP/NEXT key.
TURNING AN ALARM ON/OFF
In Alarm mode:
1. Select ALARM 1, 2 or 3 by PRESSING the STOP/NEXT key.
english
2. Toggle between ON and OFF by
25
PRESSING the START/LAP key.
TO SET AN ALARM
In Alarm mode:
1. Select ALARM 1, 2 or 3 by PRESSING the STOP/NEXT key.
PRESS & HOLD the SET/CLEAR key to enter the setting sequence.
2.
3. Adjust HOURS by
4. Advance to set MINUTES by
START/LAP or STOP/NEXT keys.
the
PRESS SET/CLEAR to exit the setting sequence.
5.
PRESSING the START/LAP or STOP/NEXT keys.
PRESSING the MODE key. Adjust by PRESSING
english
26
OPERATING THE WATCH
OPERATING THE WATCH
OPERATING THE CHRONOGRAPH
Enduro watches are equipped with a 24-hour, 100-lap Chronograph with 1/100-second
resolution.
In Chronograph mode:
1.
PRESS the START/LAP key to BEGIN TIMING.
2. To ACTIVATE A LAP,
3. To STOP TIMING,
4. To RESUME TIMING,
5. To SAVE CHRONOGRAPH DATA, when chronograph is stopped,
the STOP/NEXT key. File will be saved to memory and chronograph will
HOLD
reset to 00:00:00.
6. To RESET CHRONOGRAPH (without saving data),
english
27
CLEAR
key.
PRESS the START/LAP key.
PRESS the STOP/NEXT key.
PRESS the START/LAP key.
PRESS &
PRESS & HOLD the SET/
COMPASS QUICKACCESS (ENDURO COMPASS ONLY)
When Chronograph is running, you can access the compass by
PRESSING the SET/CLEAR key. Compass will display for 10
seconds then return to Chronograph screen.
NOTE: When chronograph is running, and Time mode is
active: CHRONO icon is displayed. The 32-segment ring around
the outer portion of the display will indicate the chronograph is
running.
CHRONOGRAPH DATA REVIEW MEMORY
Enduro watches have a memory that allows you to store up to 20 runs/workouts.
Information recorded includes time and split for each lap, best (fastest) lap, average lap
time and total time for workout. When you store a Run/Workout it is captured by the
Chronograph Data Review memory.
MANAGING THE CHRONOGRAPH DATA LOG
Runs are stored in chronological order (earliest to latest). The center line of the
display will indicate the number 1-20 and the lower line will display the DATE the
run/workout was recorded.
(
CONTINUED NEXT PAGE)
english
28
OPERATING THE WATCH
OPERATING THE WATCH
REVIEWING RUNS/WORKOUTS
In Review mode:
1. Scroll through the STORED RUNS by PRESSING the
STOP/NEXT key.
2. Select FILE TO REVIEW by
key.
3. View LAP, SPLIT, BEST, AVERAGE and TOTAL TIMES
PRESSING the START/NEXT key.
by
PRESS the STOP/NEXT key to exit file review and return
4.
to Review directory.
5. To ERASE a stored file,
key. The display will indicate file has been erased.
6. To CLEAR all files in memory,
english
29
key until display indicates “ALL ERASED”.
CLEAR
PRESSING the START/LAP
PRESS & HOLD the SET/CLEAR
PRESS & HOLD the SET/
OPERATING THE COUNTDOWN TIMERS
Enduro watches are equipped with 3 independent 24-hour
Timers with enhanced functionality. In Timer mode, you can
scroll through TIMERS 1 through 3 by PRESSING the STOP/
key.
NEXT
In Timer mode:
1. Select TIMER 1, 2, or 3 by
key. The TIMER FORMAT is indicated on the bottom
display line (CD-STOP, CD-REPT, CD-UP, or TRAIN).
PRESS START/LAP to START TIMER.
2.
PRESS STOP/NEXT to STOP TIMER.
3.
4. When timer is stopped,
PRESSING the STOP/NEXT
PRESS SET/CLEAR to RESET TIMER.
COMPASS QUICKACCESS (ENDURO COMPASS ONLY)
When Timer is running, you can access the compass by
PRESSING the SET/CLEAR key. Compass will display for 10
seconds then return to Timer screen.
english
30
OPERATING THE WATCH
FUNCTIONAL SPECIFICATIONS AND RANGES
OPERATING THE COMPASS (ENDURO COMPASS ONLY)
1. The Enduro Compass is equipped with a digital magnetic
compass with reading in one-degree increments.
2. Advance to COMPASS MODE by
key.
3. To ACTIVATE COMPASS READING,
START/LAP or STOP/NEXT key.
4. Compass will be active for 10 seconds.
5. Large LCD numbers indicate CURRENT BEARING (arrow
at top of watch).
6. LCD indicates current direction (arrow at top of watch): N,
NNE, NE, ENE, E, etc.
7. Outer display ring is used to form an arrow that points
english
north; the front of the arrow is a single segment and the
back of the arrow is 5 segments.
NOTE: To save power, the compass feature of the
unit only remains active for a period of 10 seconds. To
reactivate the compass display,
LAP or STOP/NEXT key.
31
PRESSING the MODE
PRESS the
PRESS the START/
GENERAL
Operational Temperature -10°C to +50°C/ 14°F to 120°F
50 Meter Water Resistant
Watch Battery CR 2032 3v Lithium
EL Backlight System with Auto EL-Feature
Approximate battery life: 1 year
WATCH
Auto Calendar 2006-2054
Time of Day – 12 or 24-hr. formats with 1-second
resolution
Daily Alarm – 24 hours with 1-minute resolution
CHRONOGRAPH
24 Hour Chrono 1/100 second resolution
100 Laps with up to 20 sessions of Workout
Memory
100 Split Time with Workout Memory /
20 sessions
Training Log with Best/Average Lap and Total
Training Time
Split/Lap Display user selectable
TIMER
3 Independent Timers
9 interval Timers
Maximum setting time 23h 59m 59s
COMPASS CARDINAL POINTS
N : 348 – 359 ; 0 – 10
NNE : 11 – 32
NE : 33 – 55
ENE : 56 – 77
E : 78 – 100
ESE : 101 – 122
SE : 123 – 145
SSE : 146 – 167
S : 168 – 190
SSW : 191 – 212
SW : 213 – 235
WSW : 236 – 257
W : 258 – 280
WNW : 281 – 302
NW : 303 – 325
NNW : 326 – 347
english
32
TROUBLE SHOOTING BASIC
TROUBLE SHOOTING BASIC
Your Enduro watch is a very sensitive and sophisticated instrument. If properly cared for
it should last and remain accurate for many years. However, from time to time problems
may occur. It has been our experience that the majority of the problems seen by
consumers with products such as the Enduro are related to dead or dying batteries.
While the estimated life of a fresh battery in the unit is approximately 1 year, this
can be shortened considerably if the backlight feature of the unit is used extensively.
Whenever you are experiencing issues related to the function of the unit, it is
recommended that you install a fresh battery as a first course of action, especially if it
has been more than a half a year since the last time the battery was replaced.
BE AWARE: Lithium batteries of the type used in this watch are very susceptible to
improper storage. Many times, batteries purchased as new are dead or weak before
they are purchased. Do not assume that batteries in stores are good. If you try a new
battery and problems persist, please try a second battery from another source, just to
english
be certain.
33
If the battery on the watch unit is failing it may show itself in several ways. Indications
of a weak battery are:
A fading or blank display. Also if the display goes blank when the backlight is operated
and then comes back on when the backlight system turns off.
Inaccurate readings from the compass (
If the display goes blank when the EL system is operated and then comes back on when
the EL system turns off.
The display of your watch may “freeze” due to static electricity or battery replacement.
If this occurs, remove the battery and re-insert it. This will erase the data in the memory
and reset the watch to factory settings.
Enduro watches are equipped with a display which allow them to be used in a wide
variety of environments. However, if the unit is used in extreme cold (<32°F or 1°C) the
function of the display may be slower than normal. If exposed to extreme heat or cold,
the display may also darken. The display should return to normal once the temperature
returns to normal levels.
ENDURO COMPASS ONLY).
ENDURO COMPASS ONLY
Because the compass is magnetic it may be affected by local sources of electromagnetic radiation (EMI). Avoid using the compass near appliances, in cars, near home
security systems and other sources of EMI.
english
34
SET/CLEAR KEY
MODE KEY
START/LAP KEY
EL/LIGHT KEY
HIGHGEAR USA/TECHTRAIL INC.
web: www.highgear.com
www.techtrail.com
email: contacts@highgear.com
© 2006 HighGear USA/TechTrail, Inc.
All Rights Reserved.
STOP/NEXT KEY
Loading...