Hifonics TPS-CP80 Quick Start Installation Manual

The TPS-CP80 clamping system is designed for towers and support structures that utilize ROUND
tubing. Oval tubing and at structures will not
work with this clamp. The TPS-CP80 clamp can be used with tube diameters from 1.5” up to
2.75”. Included are separate bushing sets for all tube sizes at 1/8” increments. Refer to the table
Choose a suitable mounting location
Mounting Location
Dimensions
CAUTION
Always consider consulting a professional audio installer before installing new speakers. Many manufacturers locate speakers behind interior panels that require special tools to
remove. Be careful and take your time. If you are using the speaker wire supplied with your new speakers make sure that you run the speaker wires only
through safe areas. Do not let speaker wire make contact with
metal edges or hot engine components.
Congratulations on your choice of a Hifonics speaker.
This “Quick Start” Installation guide is meant to help you complete a basic installation. For more detailed
information on system setting, speaker and subwoofer
conguration, and full specications by model, visit our
website at hifonics.com
It’s a good idea to conrm that you have purchased the correct size speakers to t your application. If you have any
reservations about being able to complete the installation yourself, we recommend contacting a professional.
Before you start
Carefully select a route for the audio signal
wires. If using existing speaker wires, conrm
that the wire is in good shape and not shorted. In the case of an illuminated model, route a positive and negative wire from a switched +12V source. Avoid routing wires through dangerous areas. Attach the positive illumination lead to either of the BLUE or the RED termination point.
Route signal and illumination wires
Wiring
230mm
9.04”
104mm
4.08”
44mm
1.73”
274mm
10.78”
215mm
8.47”
Tube
Diameter
Tube
Circumference
Clamp Top
Bushing
Bottom
Bushing
1.5 4.71 A 1.50 1.50
1.625 5.10 A 1.63 1.63
1.75 5.50 A 1.75 1.75
1.875 5.89 A none 1.88
2 6.28 B 2.00 2.00
2.125 6.68 B 2.13 2.13
2.25 7.07 B 2.25 2.25
2.375 7.46 B 2.38 2.38
2.5 7.85 B 2.50 2.50
2.625 8.25 B 2.68 2.68
2.75 8.64 B none none
Black ...................................... Audio signal negative
Black w/white stripe ................ Audio signal positive
Black ....................................... Illumination negative
Red ......................................... Illumination positive
Hifonics products are designed and engineered in the USA by
www.maxxsonics.com
Quick Start
Installation Guide
WARRANTY
Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from defects in material and workmanship for a period of one (1) year from the date of purchase. Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty period. Components that prove to be defective in materials and workmanship under proper installation and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was purchased. A photocopy of the original receipt must accompany the product being returned. The costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics
USA Inc. This warranty is limited to defective parts and specically excludes any incidental or
consequential damages connected therewith. To view the full warranty, please visit the website.
TPS-CP80
HF TPS-CP80 QSG 01 - rev1
Your TPS-CP80 speakers can be aligned to “hang straight” on an angled tube by loosening, rotating and re-mounting the speaker. Just behind the speaker mounting holes is a series mounting holes that can be used to align the speaker in the pod.
Adjust the speaker alignment
Grill alignment
Loading...