HID Global RKCLB40E, RPKCL40E Installation Guide

INSTALLATION GUIDE

iCLASS SE® Biometric/
iCLASS SE Display Reader

RKCL40, RPKCL40, RKCLB40
SRD MODEL: RPKCL40E, RKCLB40E

PLT-02738 A.0

Parts

1 - Reader and base plate assembly

1 - Installation guide

2 - Terminal connector

4 - M3.5 mm x 12 mm Phillips machine screw

4 - #6-32 x .375” Phillips self-tapping machine screw

4 - #6 x 1.5” Phillips sheet metal screw

3 - #6-32 x .4375” Spanner security screw, anti-tamper (black)

3 - #6-32 x .4375 Phillips security screw (black)

1 - Mounting Gasket

Recommended

• Cable, 6 conductor, 22 or 24 AWG [65 mm or 51 mm] Twisted Pair, Over-All Shield (Belden 3108A or equivalent) - RS-485 + power

• Cable, 6 to 9 conductor, 22 or 24 AWG [65 mm or 51 mm] Over-All Shield, (Alpha 1296C or equivalent) - Wiegand + power

• DC power supply

• Metal or plastic double-gang junction box

• Reader spacer when using metal junction boxes - see How to Order Guide

• Security tool (for spanner security screw, anti-tamper) HID 04-0001-03

Specifications

AVG

1

CURRENT
Maximum

2

AVG

PEAK

OPERATING

3

TEMPERATURE

-4° to 149° F

(-20° to 65° C)

14° to 122° F

(-10° to 50° C)

PRODUCT

RKCL40 923N

RPKCL40 923P

RKCLB40 924N 165mA 215mA 275mA

1

Standby AVG - RMS current draw without a card in the RF eld.

2

Maximum AVG - RMS current draw during continuous PIV card reads.
Not evaluated by UL.

3

Peak - highest instantaneous current draw during RF communication.

BASE PART

NUMBER

INPUT VOLTAGE

(VDC)

12VDC

Standby

150mA 185mA 250mA

hidglobal.com An ASSA ABLOY Group brand

CABLE LENGTH

Wiegand and RS-485

500 ft - 22 AWG (152 m)

300 ft - 24 AWG (91 m)

UL Reference Number Deciphering

Reader Colors: K = Black,

x

1

x2 Wiring: T = Terminal

x3 Communications: R = Module

UL REF

NUMBER

RPKCL40Ex

RKCLB40E

SRD

Model

RPKCL40E

1x2x3

x1x2x3RKCLB40E

INSTALLATION GUIDE

Installation

1 Mounting

Attach Backplate and Mounting Gasket to Junction Box.

Install gasket

Wall backplate

2 Wiring

Beeper

DRAIN

HOLD

+VDC

GPIO1
GP102

GND

OC/TMPR
DATA1/CLK
DATA2/DATA

RED

GPIO3
GPIO4

GRN LED

iCLASS SE Biometric/iCLASS SE Display

Junction box not
included.

Reverse Configuration Rotating the backplate
180° allows for placing the LCD display on left
and the reader on right.

See Section B Alternate Reader Assembly for
instructions, before proceeding to Section 2:
Wiring.

RKCL40E, RPKCL40E, RKCLB40E

SRD Model: RPKCL40E, RKCLB40E

Mounting holes for US double­gang electrical boxes.

ATTENTION

Observe precautions for handling

Terminal Reader

(Terminal block and

module position varies)

GRN LED

Beeper

DRAIN

HOLD

+VDC

GND

RED

P1

GPIO1

GP102

OC/TMPR

DATA1/CLK

DATA2/DATA

GPIO3

GPIO4

P2

ELECTROSTATIC SENSITIVE DEVICES

Note: Previous iCLASS readers had reversed

RS-485 wiring ( P2-7 & P2-6 - A & B).

When upgrading, ensure proper connections

as dened below.

Pigtail Terminal Description Pigtail Terminal Description

Yellow P1-1 Beeper Input Red / Green P2-7 GPIO1 (RS232-T / RS485-FDX/HDX-A)

Orange P1-2 LED Input (GRN) Ta n P2-6 GPIO2 (RS232-R / RS485-FDX/HDX-B)

Black P1-3 Ground (RTN) Violet P2-5 *Open Collector Output / Tamper

Red P1-4 +VDC White P2-4 **Wiegand Data 1 / Clock

Drain P1-5 Unused Green P2-3 **Wiegand Data 0 / Data

Brown P1-6 LED Input (RED) Pink P2-2 GPIO3 (RS485-FDX-Z)

Blue P1-7 Hold Input Gray P2-1 GPIO4 (RS485-FDX-Y)

*Tamper Output - When activated, output synchronizes to ground (default).

**Dependent upon reader conguration. See the HTOG for Wiegand and Clock-in-Data congurations.

This Installation Guide is for informational purposes only. HID makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output
are fictitious. Specifications are subject to change without notice.

© 2016 HID Global Corporation/ASSA ABLOY AB. All rights reserved. HID, the HID logo, and iCLASS are trademarks or registered trademarks of HID Global, or its licensors, in the U.S.
and/or other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners.

hidglobal.com An ASSA ABLOY Group brand

INSTALLATION GUIDE

iCLASS SE Biometric/iCLASS SE Display

3 Attach to Backplate

RKCL40E, RPKCL40E, RKCLB40E

SRD Model: RPKCL40E, RKCLB40E

Mount the Reader Assembly (Reader,
LCD Assembly, and reader backplate)
to the wall backplate.

4 Power & Testing

Standard Configuration: Slide Reader

Assembly towards the right to lock.

Alternate Configuration: Slide Reader
Assembly to the left to lock.

Install Security screws.

This Installation Guide is for informational purposes only. HID makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output
are fictitious. Specifications are subject to change without notice.

© 2016 HID Global Corporation/ASSA ABLOY AB. All rights reserved. HID, the HID logo, and iCLASS are trademarks or registered trademarks of HID Global, or its licensors, in the U.S.
and/or other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners.

hidglobal.com An ASSA ABLOY Group brand

INSTALLATION GUIDE

iCLASS SE Biometric/iCLASS SE Display

A Biometric Reader

Proper Usage

Ensure a good quality Contact:

• Do not press too hard

• Do not move during image acquisition

• Leave your finger on the sensor at least 2 seconds

• Do not slide or roll your finger across the sensor

Cleaning

For optimum performance, it is recommended that the user clean the bio-reader periodically.

The use of a dry cloth is recommended to clean the acquisition surface.

Caution: Acidic liquids, alcohol or abrasive materials are prohibited.

In order not to scratch the surface, remove all dust and residue with gentle movements.

RKCL40E, RPKCL40E, RKCLB40E

SRD Model: RPKCL40E, RKCLB40E

Acquisition Surface

B Credential Presentation Best Practices

To ensure a successful read of a card:

1. Hold card between the thumb and index finger.

2. Present the card so that the index finger creates a spacing between the card and the reader face.

Do not place the card flat on the reader.

3. Place the card parallel to the reader form factor. Do not angle to the right or left

4. Place the card parallel to the reader face. Do not angle the card up or down from the reader face.

This Installation Guide is for informational purposes only. HID makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output
are fictitious. Specifications are subject to change without notice.

© 2016 HID Global Corporation/ASSA ABLOY AB. All rights reserved. HID, the HID logo, and iCLASS are trademarks or registered trademarks of HID Global, or its licensors, in the U.S.
and/or other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners.

hidglobal.com An ASSA ABLOY Group brand

INSTALLATION GUIDE

iCLASS SE Biometric/iCLASS SE Display

E Alternate Reader Assembly

The following steps reconfigure the reader assembly to
position the LCD Display component on the left side
of theassembly.

1. Disassemble the Reader.

• Remove the Reader from the backplate.

• Carefully unplug the ribbon cable from the module in the
back of the Reader. Caution: Do not pull on the
ribbon cable as this may damage the connection to the
connector.

• Remove the LCD Display from the backplate.

• Gently pull the ribbon cable through the backplate.

Reader Backplate

Ribbon cable

Standard Configuration

Reader LCD Display

RKCL40E, RPKCL40E, RKCLB40E

SRD Model: RPKCL40E, RKCLB40E

Alternate Configuration

LCD Display Reader

Reader

2. Reassemble with the LCD Display on the left side of the assembly.

• Rotate the backplate so that the large cutout for the power cable is on the left

• Gently route the ribbon cable back through the backplate slots, as shown below

• Plug the ribbon cable back into the module (back of Reader) and ensure module is fully
seated into the reader

• Attach the LCD Display to the backplate (this must be installed first, as the Reader will fit
slightly over the LCD Display)

• Attach the Reader to the backplate (power cable must be threaded through the large
square cutout on the backplate)

• Return to Section 2.

Ribbon cable

Reader Backplate

LCD Display

Test card

LCD Display

This Installation Guide is for informational purposes only. HID makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output
are fictitious. Specifications are subject to change without notice.

© 2016 HID Global Corporation/ASSA ABLOY AB. All rights reserved. HID, the HID logo, and iCLASS are trademarks or registered trademarks of HID Global, or its licensors, in the U.S.
and/or other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners.

hidglobal.com An ASSA ABLOY Group brand

Reader

INSTALLATION GUIDE

iCLASS SE Biometric/iCLASS SE Display

RKCL40E, RPKCL40E, RKCLB40E

SRD Model: RPKCL40E, RKCLB40E

Regulatory

The final product, containing the modular transmitter must be labeled with its own FCC ID and IC ID. If the FCC & IC ID is not visible,
when the module is installed inside another device, then the final assembly label must contain the FCC and IC ID numbers with a
statement such as follows: “Contains Transmitter Module with FCC ID JQ6-ICLASSBTM and IC ID 2236B-ICLASSBTM”.

UL

Connect only to a Listed Access Control / Burglary power-limited power supply. These readers are intended to be used with listed
(UL294) control equipment. Suitable for outdoor use.
Only Wiegand and RS-485 communications have been evaluated by UL.

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.

CAUTION: Any changes or modifcations to this device not explicitly approved by the manufacturer could void your authority to
operate this equipment.

Indala Prox products RP10EL, RP15EL, RP30EL, RP40EL and RPK40EL are certified for FCC, Canada Radio Certification and CE Marking
only.

Canada Radio CeRtiFiCation

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Ce MaRking

HID Global hereby declares that these proximity readers are in compliance with the essential requirements and other relevant provisions
of Directive 1999/5/EC.

Por el presente, HID Global declara que estos lectores de proximidad cumplen con los requisitos esenciales y otras disposiciones
relevantes de la Directiva 1999/5/EC.

HID Global déclare par la présente que ces lecteurs à proximité sont conformes aux exigences essentielles et aux autres stipulations
pertinentes de la Directive 1999/5/CE.

A HID Global, por meio deste, declara que estes leitores de proximidade estão em conformidade com as exigências essenciais e outras
condições da diretiva 1999/5/EC.

HID Global bestätigt hiermit, dass die Leser die wesentlichen Anforderungen und anderen relevanten Bestimmungen der Richtlinie
1999/5/EG erfüllen.

HID Global dichiara che i lettori di prossimità sono conformi ai requisiti essenziali e ad altre misure rilevanti come previsto dalla Direttiva
europea 1999/5/EC.

Download copies of the R&TTE Declaration of Conformity (DoC) at http://www.hidglobal.com/certifications.

BRaziL

Compliance Statement

Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e atende
aos requisitos técnicos aplicados. Para maiores informações, consulte o site da ANATEL - www.anatel.gov.br

This product is homologated at ANATEL according to procedure regulated by Resolution 242/2000, and it complies with the applicable
technical requirements. For more information, consult ANATEL website - www.anatel.gov.br

RF Warning Statement

Per Article 6 of Resolution 506, equipment of restricted radiation must carry the following statement in a visible location:

Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações
do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.

This equipment operates in secondary character, meaning it does not have the right of protection against harmful interference, even
against those the same character, and it cannot cause any interference to systems operating in the primary character.

This Installation Guide is for informational purposes only. HID makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output
are fictitious. Specifications are subject to change without notice.

© 2016 HID Global Corporation/ASSA ABLOY AB. All rights reserved. HID, the HID logo, and iCLASS are trademarks or registered trademarks of HID Global, or its licensors, in the U.S.
and/or other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners.

hidglobal.com An ASSA ABLOY Group brand

INSTALLATION GUIDE

Fabricante: HID Global Corporation

Modelo: iCLASS SE RK40E, multiCLASS RPK40E

Este produto esta aprovada pela Anatel, de acordo com os procedimentos regulamentados pela

Resolução nº 242/2000 e atende aos requisitos técnicos aplicados.

secundário, isto é, não tem direito a proteção

estações do mesmo tipo, e não pode causar

interferência a sistemas operando em caráter

iCLASS SE Biometric/iCLASS SE Display

iCLASS Keypad Readers

FOTO SELO ANATEL

“Este equipamento opera em caráter

contra interferência prejudicial, mesmo de

primário”

RKCL40E, RPKCL40E, RKCLB40E

SRD Model: RPKCL40E, RKCLB40E

iCLASS Non-Keypad Readers

FOTO SELO ANATEL

Fabricante: HID Global Corporation

Modelo: iCLASS SE R10, multiCLASS RP10E, multiCLASS RP30E

iCLASS SE R40E, multiCLASS RP15E, multiCLASS RP40E

Este produto esta aprovada pela Anatel, de acordo com os procedimentos regulamentados pela

Resolução nº 242/2000 e atende aos requisitos técnicos aplicados.

“Este equipamento opera em caráter

secundário, isto é, não tem direito a proteção

contra interferência prejudicial, mesmo de

estações do mesmo tipo, e não pode causar

interferência a sistemas operando em caráter

primário”

This Installation Guide is for informational purposes only. HID makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output
are fictitious. Specifications are subject to change without notice.

© 2016 HID Global Corporation/ASSA ABLOY AB. All rights reserved. HID, the HID logo, and iCLASS are trademarks or registered trademarks of HID Global, or its licensors, in the U.S.
and/or other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners.

hidglobal.com An ASSA ABLOY Group brand

INSTALLATION GUIDE

iCLASS SE Biometric/iCLASS SE Display

RKCL40E, RPKCL40E, RKCLB40E

SRD Model: RPKCL40E, RKCLB40E

taiwan

According to “Administrative Regulations on Low Power Radio Waves Radiated Devices” Without permission granted by the NCC,
any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as
well as performance to a approved low power radio-frequency devices. The low power radio-frequency devices shall not influence
aircraft security and interfere legal communications; If found, the user shall cease operating immediately until no interference is
achieved. The said legal communications means radio communications is operated in compliance with the Telecommunications Act.
The low power radio-frequency devices must be susceptible with the interference from legal communications or ISM radio wave
radiated devices.

Japan MiC

“ この装置は総務省の型式指定を受けています。”
(総務省指定番号は第AC-ｘｘｘｘｘ号です)
本製品は電波を使用したRFID 機器の読み取り・書き込み装置です。
そのため使用する用途・場所によっては、医療機器に影響を与える恐れがあります

SingapoRe

Complies with

IDA Standards

DA103548

koRean kCC

R10E, R15E, R30E, and R40E RP10E, RP15E, RP30E and RP40E

RK40E RPK40E

항목 규격

송신주파수

수신주파수

출력

전원

전파형식

발진방식

변조방식

RFID:13.56 MHz

RFID:13.56 MHz

RFID: 10m에서

47.544mv이하

DC 16.0V

A1D

X-tal

AM AM(13.56MHz), FSK(125kHz)

RFID:13.5607 MHz,

LPD:125 KHz

RFID:13.56 MHz,

LPD:125 KHz

RFID: 10m에서 47.544mv이하.

LPD:3 m 거리에서 500 ㎶/m이하

X-tal (13.56MHz)

Resonator(125kHz)

HID Global

Americas & Corporate

611 Center Ridge Drive
Austin, TX 78758
USA
Support: 866-607-7339
Fax: [phone]

For additional oces around the world, see www.hidglobal.com corporate oces.
HID Global Customer Support: www.hidglobal.com/support

Asia Pacific

19/F 625 King's Road
North Point, Island East
Hong Kong
Support: 852-3160-9833
Fax: [phone]

Europe, Middle East & Africa

Phoenix Road
Haverhill, Suolk CB9 7AE
England
Support: 55 11 5514-7100
Fax: [phone]

Equipment
8T29
ACC Control Reader

hidglobal.com An ASSA ABLOY Group brand

General Signaling
Equipment