HID Global ICLASSU90 User Manual

Download

Page 1

ACCESS ﬂexibility.

U90 (U90.915 & U90.865) Reader

iCLASS SE

INSTALLATION GUIDE

Ultra High Frequency

PLT-01545, A.0

Page 2

iCLASS SE

U90 (U90.915 & U90.865)

Parts List

Parts

1 - iCLASS Reader

1 - Installation Guide

2 - #6-32 x .375” Phillips machine screws

2 - #6-32 x .375” Spanner security screw, anti-tamper

2 - 7-pin Terminal connectors

1 - 10-pin Terminal connector

1 - Mounting Gasket

1 - Back Box

recommended

• Cable, 5-9 conductor (Wiegand or clock-and-data)

• Linear DC Power supply

• Metal or plastic junction box

• Security Tool (for anti-tamper screw) HID 04-0001-03

• Drill with various bits for mounting hardware

• Mounting Hardware

PLT-01545, A.0

Speciﬁcations

Standby

AVG

CURRENT

Max

AVG

PEAK

OPERATING

TEMPERATURE

-30° to 150° F

(-35° to 65° C)

CABLE LENGTH

Power Supply Lines

40 ft (12 m) - 22 AWG 100 ft (30 m) - 18 AWG

Communication Lines

Wiegand / Clock-and-Data

500 ft (152 m) - 22 AWG

RS-485

4,000 ft (1,219 m) - 24 AWG

UL Reference Number Deciphering

x1 Reader Colors: K = Black

x2 Wiring: T = Terminal

x3 Communications: N = No Module

UL REF

NUMBER

U90Ax1x2x

PRODUCT

U90 960N

BASE PART

NUMBER

INPUT

VOLTAGE (VDC)

12 VDC 320mA 400mA 1.0 A

24 VDC 160mA 200mA 0.5 A

Standby AVG - RMS current draw without a card in the RF eld.

Maximum AVG - RMS current draw during continuous card reads. Not evaluated by UL.

Peak - highest instantaneous current draw during RF communication.

Relays

Three (3) each dry relays for operating external audio and visual indicators. Not to be used for Access Control. Rated 30VDC, 2A resistive.

INSTALLATION GUIDE

Page 3

PLT-01545, A.0 iCLASS SE

U90 (U90.915 & U90.865)

Mounting

200

100 75

JBOX

100

200

VESA

CONDUIT

JBOX

Mounting holes need to be drilled to mate with the mount selected for the site.

There are many options for mounting surfaces (pole, concrete, metal, wall bracket, etc.). See the iCLASS SE U90 Reader User Guide for detailed information.

200

100

200

Modify the gasket to the match the large holes on the mounting plate and to match the area between the mount and the box, to create a seal against the elements (see below).

Trim Gasket to match the contact area

Attach the box with the gasket to the mount

INSTALLATION GUIDE

Page 4

iCLASS SE

U90 (U90.915 & U90.865)

PLT-01545, A.0

Wiring

ATTENTION

Observe precautions for handling

ELECTROSTATIC SENSITIVE DEVICES

Terminal Description Terminal Description Terminal Description

P1-1 Beeper Input (BEEP) P2-1 GPIO4 (RS485-Y / TXA) P3-1 Earth Ground

P1-2 LED Input (GRN) P2-2 GPIO3 (RS485-Z / TXB) P3-2 Normally Closed (NC) - Relay 1

P1-3 Ground (GND) P2-3 ** Wiegand Data 0 / Data (DATA0/DATA) P3-3 Common (COM) - Relay 1

P1-4 +VDC P2-4 ** Wiegand Data 1 / Clock (DATA1/CLK) P3-4 Normally Open (NO) - Relay 1

P1-5 Unused (DRAIN) P2-5 * Open Collector Output / Tamper (OC/TMPR) P3-5 Normally Closed (NC) - Relay 2

P1-6 LED Input (RED) P2-6 GPIO2 (RS232-R / RS485-RXB) P3-6 Common (COM) - Relay 2

P1-7 Hold Input (HOLD) P2-7 GPIO1 (RS232-T / RS485-RXA) P3-7 Normally Open (NO) - Relay 2

P3-8 Normally Closed (NC) - Relay 3

P3-9 Common (COM) - Relay 3

P3-10 Normally Open (NO) - Relay 3

* Tamper Output - When activated, output synchronizes to ground (default).

** Dependent upon reader conguration. See the HTOG for Wiegand and Clock-in-Data congurations.

INSTALLATION GUIDE

Page 5

PLT-01545, A.0 iCLASS SE

U90 (U90.915 & U90.865)

Turn power on

Install Reader to Backbox

Power & Testing

Basic test of a card

LED is under the trap door

LED will be red (under the trap door)

LED will be Green Note: This is tested with a card mounted in a vehicle and driven by the reader.

Configurable Features

• Open Collector Output - Controls an external device (16 VDC Max) operating in Host Mode only. Sink - 40mA / Source - 1mA. See the iCLASS Application Note for details.

• Optical Tamper - Reader is configurable for Optical Tamper. Once activated, and when the reader is removed from the mounting box, the Optical Tamper is activated. Contact HID Technical Support

for Optical Tamper options. See iCLASS SE U90 User Guide.

• Hold Input - when asserted, this line either buffers a card or disables a card read until released, as configured.

INSTALLATION GUIDE

Page 6

Connect only to a Listed Access Control / Burglary power-limited power supply. These readers are intended to be used with listed (UL294) control equipment.

Only Wiegand and RS-485 communications have been evaluated by UL.

CAUTION: Any changes or modifcations to this devise not explicitly approved by the manufacturer could void your authority to operate this equipment.

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC RF Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna

Canada Radio Certification

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

CE Marking

HID Global hereby declares that these proximity readers are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Por el presente, HID Global declara que estos lectores de proximidad cumplen con los requisitos esenciales y otras disposiciones relevantes de la Directiva 1999/5/EC.

HID Global déclare par la présente que ces lecteurs à proximité sont conformes aux exigences essentielles et aux autres stipulations pertinentes de la Directive 1999/5/CE.

A HID Global, por meio deste, declara que estes leitores de proximidade estão em conformidade com as exigências essenciais e outras condições da diretiva 1999/5/EC.

HID Global bestätigt hiermit, dass die Leser die wesentlichen Anforderungen und anderen relevanten Bestimmungen der Richtlinie 1999/5/EG erfüllen.

HID Global dichiara che i lettori di prossimità sono conformi ai requisiti essenziali e ad altre misure rilevanti come previsto dalla Direttiva europea 1999/5/EC.

Download copies of the R&TTE Declaration of Conformity (DoC) at http://www.hidglobal.com/certifications.

ACCESS experience.

HID GLOBAL, HID, the HID logo, and iCLASS SE, are the trademarks or registered trademarks of HID Global Corporation, or its licensors, in the U.S. and other countries.

HID Global

Americas & Corporate

611 Center Ridge Drive Austin, TX 78753 USA Support: 866 607 7339 Fax: 949 732 2120

For additional oces around the world, see www.hidglobal.com corporate oces. HID Global Customer Support: support.hidglobal.com

Asia Paciﬁc

19/F 625 King’s Road NorthPoint, Island East Hong Kong Support: 852 3160 9833 Fax: 852 3160 4809

Europe, Middle East & Africa

Phoenix Road Haverhill, Suolk CB9 7AE England Support: +44 1440 711 822 Fax: +44 1440 714 840

Equipment 8T29

ACC Control READER

hidglobal.com

US Patents: See www.hidglobal.com/patents

Check reader label for current regulatory

PLT-01545 A.0

approvals.

Brazil

Condomínio Business Center St. Ermano Marchetti, 1435 Galpão A2 CEP 05038-001 Lapa - São Paulo/SP Brazil Support: 55 11 5514-7100

General Signaling Equipment