HID Global 609XA User Manual
Installation Guide
iCLASS™ Reader Models R10, R30, R40, RW300, RW400
PARTS INCLUDE D SPECIFI CATIONS
1 -
•
iCLASS
1 - Installation Manual
•
2 - 3.5mm x .6 pitch x 12mm Phillips machine screws
•
3 - #6-32 x .375” Phillips self-tapping machine screws
•
2 - #6 x 1.5” Phillips sheet metal screws RS-232 - 50 ft (15m)
•
1 - #6 x .375” Spanner security screw, anti-tamper
•
Recomm ended:
Up to 9 wire splices
•
Cable, 5-9 conductor (Wieg. or RS232), 22awg shielded
•
Linear DC Power supply
•
Metal or plastic junction box
•
Magnetic switch - Ademco 945T, Sentrol 1038T, GRI 100T
•
or 110T or Aleph DC-2531
Security Tool (for anti-tamper screw) HID 04-0001-03 and other 3
•
INSTALLATION
1- Disassemble
Reader
R10 (Mullion)……………..10 - 16VDC / 65-225mA
•
R30/RW300 (Euro)………10 - 16VDC / 80-260mA
•
R40/RW400 (US)………...10 - 16VDC / 80-260mA
•
Cable distance to Host…..Wiegand - 500 feet (152m) max
•
Temperature………………-35° C to 65°C
•
Open collector output…….sink - 40mA, source - 1mA
•
Standards:
Read/Write* capability in ISO 15693-2 mode with HID
•
credentials
iCLASS
Read/Write* capability in ISO 14443-B2 mode with HID
•
16Ks and other 3
iCLASS
CSN read capability for ISO 14443-A1 with HID Mifare
•
rd
party Mifare credentials
rd
party credentials
* R10, R30, R40 are read-only
1- Remove Screw
2 - Lift Bottom of Bezel 4 - Lift top o f Reader Assembly
3 - Slide Bezel up and remove 5 - Slide down and remove
2- Install Tamper Switch
An internal magnet provides tamper indication when used with a magnetic reed switch connected to an external alarm
system. (Except R10). Locate Switch behind the left side of the mounting plate, centered between the mounting holes.
Electrical Back Box
An ASSA ABLOY Group company
_____________________________________________________________________________________________________
HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690
Web page - www.hidcorp.com e-mail – tech@hidcorp.com
™ Reader Installation Manual 6090-900 Rev 8 Page 1 of
iClass
Wall Su rfa c e
ASSA ABLOY
3
Installation Guide
iCLASS™ Reader Models R10, R30, R40, RW300, RW400
3- Prepari ng/Mounting
Install Mounting Plate to wall surface or back box, t hen reassemble reader (reverse Step 1 proc edure).
Dimensions are in inches (centimeters).
R10 Mounting Plate R30/RW300 Mounting Plate R40/RW400 Mounting Plate
4- Connecting 5- Testing
Turn Power On
Yellow *Speaker
Blue *Hold
Violet ***Open Collector
Whit e Data 1
Green Data 0
Orange *Green LED
Brown *Red LED
Red +DC (10-16 VDC)
Black Ground
Gray ***RX (Serial Receive)
Red/Green ***DSR (Not Used)
Pink ***TX (Serial Transmit)
An ASSA ABLOY Group company
_____________________________________________________________________________________________________
HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690
Web page - www.hidcorp.com e-mail – tech@hidcorp.com
•
speaker tones sequence.
Use a Test Card
•
Speaker tone for each card read.
6- Optional Features
RS232 interface/Host Mode -
•
serial link. See Protocol Document 6090-902 for information
Open Collector Output –
•
(13.8VDC Max) operating in Host Mode only. See
Application Note for details
Configuration Options -
•
features. See How To Order Guide or
Note for details
™ Reader Installation Manual 6090-900 Rev 8 Page 2 of
iClass
- watch the sign-on LED and hear the
- watch for the LED flash and hear the
for applications requiring a
controls an external device
iCLASS
Configure LED, Speaker, and other
Application
iCLASS
ASSA ABLOY
3
Loading...