Page 1
PoE Power/Video/Data UTP Transceiver User Manual
INSTRUCTION MANUAL
Page 2
PoE Power/Video/Data UTP Transceiver User Manual
Summary
The unit is a device that allows the transmission of real-time video and power over Unshielded Twisted Pair cable. PoE PVD transmitter
convert unbalanced video signal to balanced (same range but opposite polarized) difference signal transmitting via the UTP cable, have good
common interferences rejection, under strong interference environment can transmit color video in high quality.
Power over Ethernet (PoE) technology describes a system to transmit electrical power, along with data, to remote devices over standard
unshielded twisted-pair (UTP) cable. In applications such as security surveillance, video conferencing, elevator surveillance the PoE PVD
transceiver use one UTP cable to replace power, video coaxial and data cables. Working hours much lessened and 70% cable cost saved.
Features
¤ Longer transmission distance, high video signal quality
Use advanced video signal technology, better equalize video signal differs attenuation in UTP cable, Keep original video signal real-time,
brightness, sharpness and colorful, and enable longer and better signal transmission.
¤ Standard and easy routing UTP, low cable and installation cost
PoE PVD transceiver use cat5 or higher cat UTP, according TIA/EIA 568A or 568B standards, can use of already installed UTP cable in
building. Transmit Power/Video/Data or Audio in a UTP cable (4 pair) for camera. Avoid the need for separate data and power cable
infrastructure and costly AC outlets, no electrician is needed, and much working hours saved.
¤ Perfect power manager for centralized power supply
Multiple power protection and working status indication, in control room diagnose remote PVD transmitter or camera fault, use together
with UPS device can continue operate even when power failure.
¤ Better surge suppression; Exceptional interference rejection
Built-in multiple surge suppression device, and have ground lifting. When surge voltage put on signal wire, the most will be induced and
released to earth ground track power ground line, left can be work out pass multiple surge suppression device.
Page 3
PoE Power/Video/Data UTP Transceiver User Manual
Applications
There are two kinds of transceivers, active and passive type, PoE work type have standard and highpower two kinds. According to different
transferring distance and camera load power, please refer to the system selection chart and PoE power chart:
No.of
Cam
1 1640ft 1000ft
1 8000ft 5000ft
4 8000ft 5000ft
1 4590ft 2623ft
4 4590ft 2623ft
1 8000ft 5000ft
UTP Length 0-1000ft 1640ft 2623ft 3279ft 4000ft 5000ft 6000ft 7000ft
Standard PoE 12V 0.75A 12V 0.5A 12V 0.32A 12V 0.26A 12V 0.21A 12V 0.17A
Highpower PoE 12V 3.5A 12V 2.4A 12V 1.5A 12V 1.2A 12V 1A 12V 0.8A 12V 0.65A 12V 0.56A
Note: The chart test result use UTP CAT5 24AWG, and high voltage of input range AC28V/DC28V for PVD receiver.
Trans Distance
B/W Color
Max output*
PoE power
Transmitter Receiver Remarks
12V 0.75A HXVB200T/TA HXVB200R/RA PoE Passive
12V 0.17A
12V 0.17A
12V 0.32A
HXVB300T
HXVB301T
HXVB300T
HXVB301T
HXVB200T
HXVB200TA
HXVB300R
HXVB301R
PoE active
HXVB604R 4ch PoE active
HXVB300R
HXVB301R
PoE passive + active
12V 0.32A HXVB200T/TA HXVB604R 4 PoE passive + active
12V 0.8A HXVB305T HXVB305R Highpower PoE active
/ /
Page 4
PoE Power/Video/Data UTP Transceiver User Manual
Applications Instruction
Page 5
PoE Power/Video/Data UTP Transceiver User Manual
Specifications
HXVB200T/T
Model
Signal
Channel
Video Frequency response range:DC-6MHz ;Common/differential mode rejection:15KHz-6MHz 60dB typ.
A
HXVB200R/R
A
1ch video
(passive)
1ch power
1ch dat/audio
HXVB201T
1ch video
(active)
1ch power
1ch data
HXVB300
T
HXVB300
R
1ch video
(active)
1ch power
1ch data
HXVB301
T
HXVB301
R
1ch video
1ch audio
(active)
1ch power
HXVB305T
HXVB305R
1ch video
(active)
1ch HPower
1ch data
HXVB408
R
8ch video
(passive)
8ch power
8ch data
HXVB604R
4ch video
(active)
4ch power
4ch data
Wire type
Impedance
Power Receiver input AC24-28V or DC30-38V(HXVB305R input DC56V);Transmitter output constant DC12V
Suppression 6kV 1.2×50uS;3kV 8×20uS 6KV 1.2uS×50uS;4KV 8uS×30uS
W / M 40g / 54*28*22.5mm 90g / 81*58*30mm | 120g 500g / 180*80*35mm
Environment
Note: HXVB305 is high-power PoE transceiver use DC56V 1A input power; other transceiver is standard PoE transceiver, use AC28 or
24AWG UTP CAT5 or higher; DC loop resistance≤18Ω/100m;Differential capacitance:62pF/m(max)
UTP or RJ45：100Ω BNC COAX：75Ω
Temperature: (0~50℃) Humidity: (0%~95%)
Page 6
PoE Power/Video/Data UTP Transceiver User Manual
DC36V 0.5A input power, so can use one 100W 36V/3A power adapter for 6 PoE Receiver.
Transceiver setting and indication
PoE PVD passive transceiver no need set gain, they have indication LED. Transmitter have power good LED, Receiver have load/unload
dual color LED.
PoE PVD active transceiver need set gain for different distance, Transmitter have power good (PG)/under voltage (UV) dual color LED,
Receiver have load/unload dual color LED, and they all have video in LED, when video input, LED will turn on.
PIN Color Function PIN Color Function
1 W-O Video+ 5 W-B Power+
2 O Video- 6 G Data-
Active tra nsmit t e r ga in set
RJ45 jack inst ructio n
10 0 0f t
13 2 7f t
16 3 9f t
20 0 0f t
21 3 0f t
24 5 8f t
26 2 2f t
30 0 0f t
327 8 f t
344 2 f t
377 0 f t
410 0 f t
3 W-G Data+ 7 W-BR Power-
4 B Power+ 8 BR Power-
42 6 1f t
45 9 0f t
47 5 3f t
50 0 0f t
Active receiver sha rpness set t ing chart (suggest for best colo r vide o t ran smit dista nce)
Page 7
PoE Power/Video/Data UTP Transceiver User Manual
Frequently Asked Question
1. What kind wire use for PoE series transceiver
We recommend use 4 pair Unshielded Twisted-Pair cable, category 3 or higher, 16-24AWG, multi-pair (6 pair or more)twisted pair is ok. If
use STP (shield twisted pair) cable, the modular plugs need to use shielded too, make sure STP shielded and modular plugs shielded connect
together. When need prolong UTP, you can use special RJ45 connect box or jointing to make connection, if in out door use, please protection
against the tide.
2. Why no interference in PoE PVD transceiver when transmitting power via UTP
PoE PVD transceiver power's working mode are based on IEEE802.3AF/AT. And this standard widely used in IPphone, IPcam, and other
Ethernet devices. No interference caused even transmitting power under 1000Mbps Ethernet. PoE PVD transceiver use safe voltage
(DC36V); the transmitter, receiver and remote powered device are at same power ground, so no maladjustment to ground voltage position,
and the signal quality will be better.
3. How can I do when remote camera power over PoE transmit power
Normal CCD camera power is 12V/0.15-0.08A, 56pcs LED IR camera power is 12V/0.5-0.4A.PoE PVD transceiver can supply most camera.
If special camera power over, please use Highpower PoE PVD transceiver, if power over PoE in 50% range, can select 2pair-3pair module,
this module converting 1pair data wire into power wire, can increase 50% standard PoE transmit power.
4. Why PoE PVD transceiver use AC24-28V/DC30-38V input voltage, whether increase the costs
For the UTP is 24AWG wire, and loop DCR 19Ω/100m,so if want to transmit larger power to remote area, it must increase the voltage to
Page 8
PoE Power/Video/Data UTP Transceiver User Manual
reduce the current, there by to reduce the power consumption. Otherwise may lead to large power lost (Voltage lost=I*R) or current limit
exceeded. Single 36V adapter more costs than 12V adapter, but PoE PVD transceiver is centralized power supply, one 36V 3A adapter can
supply 6 pairs of PoE PVD transceiver, one transceiver need 0.5A power only. Averagely ,each pair transceiver adapter cost not higher than
12V adapter.
5. Can I use CAT6 for PoE PVD transceiver
Yes,CAT6 UTP cable is better interference rejection than CAT5,and CAT6 is 23AWG large than CAT5 ,can afford more PoE power than
CAT5.
Malfunction Disposal
1. Monitor no video signal
Please check the power supply first, and then the device connector and wire joints, whether ok or not?Then check the UTP cable and modular
plugs connecting situation according to the RJ45 instruction.
2. Tilted veins interference and high frequency interference appear on the image
Please check if the camera, housing, monitor and DVR creepage, in addition make the surface of transceiver connected terra; and then check
the wire joint points connect well.
3. The image become BW form color or the color too light
If adopt active transferring project, please adjust transceiver gain, set signal to high. If use passive transferring project, please change active
transferring project.
Page 9
PoE Power/Video/Data UTP Transceiver User Manual
4. What cause about image twist and wobble
UTP RJ45 connector order mistake, please as RJ45 jack instruction connect.
5. The image to bright and white twist
The video signal too strong, please adjust sharpness DIP switch and birghtness of PVD receiver, and set to lower signal grade.
6. PoE PVD Transmitter can't power Remote camera
Check power of remote camera whether over the power corresponding to the proper distance; Check input voltage of PoE PVD receiver
whether in required range;Shut the camera power and reconnect it, to make sure that transceiver not in limited protection status; Ensure the
UTP RJ45 connector in right order, than reconnect Rj45 jack and Rj45 modular plugs.
Loading...