Page 1
HXJZ-871 Mini Power Wireless Module
User’s Manual
Page 2
HXJZ-871 Mini Power Wireless Module User’s Manual
About HXJZ-871
HXJZ-871, a Mini power wireless module, is used as the wireless data transmission in short distance.
With the characteristics of small size, light weight, low power consumption, good stability and reliability,
it can provide bidirectional data transmission, test and control for users.
It is used for Wireless meter reading, such as water meter, electric meter and gas meter, parking meter,
intellective card, electronic weighing apparatus, meter for checking on work attendance, queue wireless meter,
building control, shipping company control, alarm system, intelligent equipment, Automatic data collecting
system; Industrial remote control and remote test building automation, safety and security, powerhouse
equipment wireless monitor, entrance control system, etc.
If necessary, we can provide USB interface to make it easy to settle the question of Power Supply for
Mini computer and PC users.
Features:
1.Ultra low power transmission
The highest transmission power is 100mW, high receiving sensitivity: -121dbm,
Size: 44mm*27mm*8mm
2. ISM frequency band, not requiring on application of f requency point
Carrier frequency of 433MHz，also capable of 868/915MHz.
3. High anti-interference and low BER (Bit error Rate)
Based on the GFSK modulation mode, it adopts the efficient communication protocol. The
actual bit error rate of 10-5 ~ 10-6 can be achieved when channel bit error rate is 10-2.
4. Long transmission distance
Within the range of visibility, the reliable transmission distance is（BER=10-3/1200bps）>800m when the
antenna is higher than 3M.
5. Transparent data transmission
Transparent data interface is offered, which can be fit for nonstandard user protocol.
Any false data generated in the air can be filtrated automatically (What has been
received is exactly what has been transmitted). The change time for receiving and sending <10ms.
6. Multi-channel and speed
The HXJZ-871 provides 8 channels to meet the multiple communication combination mode of the users.
The
JZ861 Module can provide many kinds of correspondence baud rate such as 1200bps, 2400bps,
4800bps,
9600bps, 19200bps and 38400bps.
The wireless transmission speed and the connection baud rate are proportional, to satisfies the customer
equipment of different baud rate.
7. High speed wireless communication and Large data buffer
When the RF baud rate is bigger than the COM baud rate, allowing to transmit unlimited data at one time,
and when the RF baud rate is smaller than or was equal to the COM baud rate ,may transmit 255 bytes data
8. Intelligent data cont rol and the user doesn’t need to prepare excessive programs
Even for semi duplex communication, the user doesn’t need to prepare excessive
programs, only receiving/transmitting the data from the interface. HXJZ-871 will automatically
complete the other operations,
Page 3
HXJZ-871 Mini Power Wireless Module User’s Manual
such as transmission/receiving conversion in the air, control, etc.
9. High reliability, small and light
Single chip radio frequency integrated circuit and single chip MCU are used for lessened
peripheral circuits, high reliability, and low failure rate.
10. Low power consumption, two kinds of sleep mode.
Receiving current <30mA, transmitting current <100mA;
Sleeping mode (The user’s should asked for it):
a. Awaken from Hardware
b. Awaken from Interface.
The user can set it according to the software.
10. Watchdog monitor
Watchdog monitors the inner function, so it can change the traditional product structure and improve the
product reliability.
11.Antenna choose
Users can choose the antenna according to user’s different need .
Application of HXJZ-871
1. Dimensional drawing
Fig1. HXJZ-871 interface
chart
Page 4
HXJZ-871 Mini Power Wireless Module User’s Manual
Remarks: The space between each pin is 2.0 mm.
2. HXJZ-871 interface definition
HXJZ-871 can supply one 5-pin connector (JP1), and its definitions as well as connection method
for terminals are shown in Table 1.
Table 1: Definition of connecting pins and connection method
Item no
PIN
Description Level
Connected to the
terminal
User terminal
Remarks
1
VCC
+5±0.5V
+5±0.5V
TTL 3V user’s choose
2
GND
Power
supply/Ground
DGND/AGND
RS232 interface: GND of
Power
3
RXD/ B (RS-485)
Serial data receiving
end
TXD/ B (RS-485)
4
TXD/ A (RS-485)
Serial data
transmitting end
RXD/ A (RS-485)
5
SLE
Sleep control
(input)
end
High level to sleep, Low
level awake(sleep version is
aviavailability)
Note: No sleeping is default, The Pin 5 of no-sleeping version is not be used, pin 5 must be hung.
User’s equipment
+5v regulator n.
power supply
transmitter-receiver
Remarks: To avoid connecting the interface reversely and can not communicate, please check and assure
the voltage of 3 and 4 pin is existing by using multimeter. If there is one pin that has the voltage, another has
not voltage, which means the interface is connected reversely, pls. Change the connection wires between pin 3
and 4.
Page 5
HXJZ-871 Mini Power Wireless Module User’s Manual
HXJZ-871 Powersupply and sleep mode
1. Power supply
HXJZ-871 uses DC power supply with voltage of +5V. It can also share power supply with other
equipment, however, the high quality power supply with desirable ripple factor should be selected. In addition,
the reliable grounding must be used if there is other device in the system equipment. In case of failure to
connect with the earth, it can form its own grounding but it must be absolutely separated from the municipal
electric supply.
2. Sleeping function
HXJZ-871 had sleeping and no-sleeping version.
The current ofHXJZ-871 in the sleeping state is 1Ua. Users must tell which version will be chosen
before place the order in advance (No sleeping is default).
For sleeping version, users can open and close the sleeping function by themselves.
HXJZ-871 with the sleeping function has two awakening way, one is hardware awakening way, another
is interface awakening way (air awakening will be reserved) Hardware awakening is achieved by the Pin 5
input to the high level and input low level to awake.
Awaken from Interface is achieved by users send designate protocol data by HXJZ-871 interface to open
or awake. HXJZ-871 with the function of sleeping is default in close state before leaving factory, so users must
set
by HXJZ-871 software to set the awakening mode to hardware awakening or interface awakening. Users can
also tell us to set in advance.
If users use HXJZ-871 with the sleeping function, but hope not to apply the sleeping function, the users
can
set by HXJZ-871 software to set for no-sleeping state or make HXJZ-871 pin 5 to connect the ground in the
mode of hardware awaken.
HXJZ-871 parameters setting
HXJZ-871 have one interface of TTL、RS232、RS485, You must specify the interface when you buy.
HXJZ-871 main parameters: COM baud rate and verify，RF baud rate, Channel and frequency。You can
change these parameters by our RF Module soft. When RF baud rate is faster than COM baud rate，One frame
Can transmit limitless data. When RF baud rate is not faster than COM baud rate ，One frame Can transmit
255 bytes most.
You can set the rate according your need. The general Power supply is 5V DC.
Two HXJZ-871 communicate must have condition as follow:
1.Their channels (i.e. frequency) are same.
2.Their RF rates are same.
3. RF Module Com baud rate and verify is agree with its equipment or PC that it connects with.
Parameters default value:
Channel NO.：1
Interface speed rate：9600BPS
Interface verify：none
Speed rate in air：2400BPS
Page 6
HXJZ-871 Mini Power Wireless Module User’s Manual
Channel and frequency
list
Channel
Frequency
Channel
Frequency
1
430.2000MHZ
9
458.5250MHZ
2
431.4288MHZ
10
459.1250MHZ
3
431.7360MHZ
11
459.5250MHZ
4
430.5072MHZ
12
460.1250MHZ
5
434.6940MHZ
13
460.5250MHZ
6
434.2332MHZ
14
461.1250MHZ
7
433.1580MHZ
15
461.5250MHZ
8
433.9260MHZ
16
462.1250MHZ
Technical specification of HXJZ-871
Modulation mode: GFSK
Working frequency: 420 --470MHZ
Transmission power: <100mW
Receiving sensitivity: -121dBm
Transmitting current:: <100mA，
Receiving current: <30mA
Sleeping current: <15uA
Channel speed rate: 1200/2400/4800/9600/19200/38400Bit/s , User can Choose one
Interface speed rate: 1200/2400/4800/9600/19200/38400Bit/s, User can Choose one
Change time for receiving and sending: <10 ms
Interface data format:8E1/8N1/8O1
Power supply: 5±0.5V（RS232/RS485），2.7--3.6V or 3.6--5.5V（TTL）DC
Working temperature:-20℃～85℃
Working humidity: 10%～90% relative humidity without condensation
Dimension: 44mm*27mm*8mm
Attachable Communication with Model: HXJZ-871/JZ872/JZ873/JZ878/JZ875
Another style you can choose:
Transmission power: <10mW
Transmitting current: 35mA
Receiving current: 30mA
Page 7
HXJZ-871 Mini Power Wireless Module User’s Manual
Model and name
JZ
871
-T
T：TTL interface
2：232 interface
4：485 interface
Naked board no
Company logo
Optional Antenna:
Trouble and solve ways:
NO.
Trouble
Trouble causes and solve ways
1
No shine of
Indicator light
a、Power Line badness touch .
b、Power is bad.
c、Power line meet in reverse, or diode of polarity protect is bad.
2
No transmit
or
No receive
a、Radio is badness touch with PC/terminal.
b、Radio with TTL/RS232/RS485 not match terminal.
c、RX frequency and TX frequency is not same.
3
Bit error rate
High
a、antenna not match, or touch bad;
b、RF baud rate is not right. c、
Power supply ripple is too great.
4
Indicator light
twinkling
a、Electromagnetism disturb in circumstance.
b、Same frequency disturb in the circumstance.
Loading...