Hewlett Packard Enterprise DNMA83 User Manual

WLAN mini PCI Card

H3C DNMA-83 User Manual

Version: 1.0

Nov 2007

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Windows™ 98SE/2000/ME/XP are trademarks of Microsoft® Corp. Pentium is trademark of Intel.

All copyright reserved.

FCC Statement

Warning: Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IEEE 802.11a operation of this product in the U.S.A. High power radars are allocated as primary users of the 5.25 to 5.35GHz and 5.47 to

5.725GHz bands, do not use these bands.

To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons.

This Transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users. For laptop installations, the antenna must be installed to ensure that the proper spacing is maintained in the event the users places the device in their lap during use (i.e. positioning of antennas must be placed in the upper portion of the LCD panel only to ensure 20 cm will be maintained if the user places the device in their lap for use) and The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter testing will not be required.

However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).

NOTE: In the event that these conditions can not be met (for example certain laptop

configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product.

In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

End Product Labeling

This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example access points, routers, wireless ASDL modems, certain laptop configurations, and similar equipment). The final end product must be labeled in a visible area with the following: "Contains

RF Exposure Manual Information That Must be Included

TX FCC ID: O9C-DNMA83 ".

The users manual for end users must include the following information in a prom inent location

NOTE: To comply with FCC RF exposure compliance requirements, the antenna used

for this transmitter must be installed to provide a separation distance of at least 20 cm

from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter."

Additional Information That Must be Provided to OEM Integrators

The end user should NOT be provided any instructions on how to remove or install the device.

Service Center in U.S.A

Company Name : 3Com Corporation Company Address: 350 Campus Drive, Marlborough, MA 01752-3064. U.S.A.

Service Center in Canada

Company Name : 3Com Canada Company Address: 466 Speers Road 3rd Floor Oakville, ON, L6K 3W9

Table of Contents

1. INTRODUCTION 6

2. DRIVER/UTILITY INSTALLATION / UNINSTALLATION 7

2.1 INSTALLATION..........................................................................................................7

2.2 ADDITIONAL SETUP PROCESSES............................................................................10

2.3 UNINSTALLATION...................................................................................................11

3. CONNECTING TO AN EXISTING NETWORK 12

4. CREATING AN AD HOC NEW NETWORK 17

5. MODIFYING A WIRELESS NETWORK 21

5.1 INFRASTRUCTURE MODE AND AD HOC MODE .....................................................21

5.2 MODIFYING A WIRELESS NETWORK.....................................................................22

5.3 DEF AULT SETTINGS WINDOWS XP ZERO-CONFIGURATION................................29

5.4 SUPER A/G SETTING ...........................................................錯誤! 尚未定義書籤。

APPENDIX A: F AQ ABOUT WLAN 30

APPENDIX B: SPECIFICATION 32

1. Introduction

Thank you for purchasing the WLAN a/b/g/n mini-PCI Module that provides the easiest way to wireless networking. This User Manual contains detailed instructions in the operation of this product. Please keep this manual for future reference.

System Requirements

z A laptop PC contains:

- 32 MB memory or greater

- 300 MHz processor or higher

z Microsoft® Win™2000/ME/98 Second Edition/XP

2. Driver/Utility Installation / Uninstallation

2.1 Installation

Note! The Installation Section in this User Manual describes the first-time installation

for Windows. To re-install the driver, please first uninstall the previously installed driver. See Chapter 2.3 “Uninstallation” in this User Manual.

Follow the steps below to complete the driver/utility installation:

1. Insert the Installation Software CD into the CD-Rom Drive.

2. Click “Next”.

3. Read the License Agreement and click “Yes”.

4. Click “Next” to continue or click “Browse” to choose a destination folder.

5. Click “Next”.

6. Click “Yes” to create a shortcut icon on your desktop.

7. Click “Finish”.

8. You should now see a shortcut icon on your desktop.

2.2 Additional Setup Processes

During software installation procedure, each operating system may prompt different specific options:

1. Windows 98SE: The system will request the original Windows CD during the

installation process. When the installation is finished, you’ll have to restart your computer.

2. Windows Me: Please restart your computer when the installation is finished.

3. Windows 2000/XP: Select “Install the software automatically” when the window

with this option appears, and then click “Next” to continue installation.

+ 24 hidden pages