Hewlett Packard Enterprise AP9293SDR Installation Guide

IAP-92 and IAP-93 Wireless Access Point

Installation Guide

About the Aruba IAP-92/IAP-93

The Aruba IAP-92 and IAP-93 are single-radio, dual-band wireless access points that support the IEEE 802.11n standard for high-performance WLAN. These access points use MIMO (Multiple-in, Multiple-out) technology and other highthroughput mode techniques to deliver high-performance, 802.11n 2.4 GHz or 5 GHz functionality while simultaneously supporting existing 802.11a/b/g wireless services. The IAP-92 and IAP-93 access points work only in conjunction with an Aruba Controller.

The Aruba IAP-92/IAP-93 access point provides the following capabilities:

 Wireless transceiver  Protocol-independent networking functionality  IEEE 802.11a/b/g/n operation as a wireless access point  IEEE 802.11a/b/g/n operation as a wireless air monitor  Compatibility with IEEE 802.3af PoE  Central management configuration and upgrades through an Aruba

Controller

The Aruba IAP-92/IAP-93 requires ArubaOS 5.0.1 or later.



Package Contents

 IAP-92 or IAP-93 access point  Installation Guide

Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use



Figure 1 IAP-92/IAP-93 (IAP-92 Shown)

IAP-92/IAP-93 Hardware Overview

Figure 2 Front (IAP-92 Shown)

LEDs

 PWR: Indicates whether or not the IAP-92/IAP-93 is powered-on  ENET: Indicates the status of the IAP-92/IAP-93’s Ethernet port  11A/N: Indicates the status of the 802.11a/n radio  11B/G/N: Indicates the status of the 802.11b/g/n radio

For information about the IAP-92/IAP-93’s LED behavior, see Table 1.

these materials to repack and return the unit to the supplier if needed.

AP-92_001

Figure 3 Rear (IAP-92 Shown)

ENET

Antenna Connector

(IAP-92 Only)

12V 1.25A

CONSOLE

Antenna Connector (IAP-92 Only)

AP-92_002

Console Port

Use the console port to connect to a terminal for direct local management.

Ethernet Port

IAP-92/IAP-93 is equipped with a single 10/100/1000Base-T (RJ-45) auto-sensing, MDI/MDX wired-network connectivity port. This port supports IEEE 802.3af Power over Ethernet (PoE) compliance, accepting 48VDC as a standard defined Powered Device (PD) from a Power Sourcing Equipment (PSE) such as a PoE midspan injector, or network infrastructure that supports PoE.

DC Power Socket

If PoE is not available, an optional Aruba AP AC-DC adapter kit (sold separately) can be used to power the IAP-92/IAP-93.

Reset Button

The reset button can be used to return the AP to factory default settings.. To reset the AP:

1. Power off the AP.

2. Press and hold the reset button using a small, narrow object, such as a paperclip.

3. Power-on the AP without releasing the reset button. The power LED will flash within 5 seconds.

4. Release the reset button.

The power LED will flash again within 15 seconds indicating that the reset is completed. The AP will now continue to boot with the factory default settings.

External Antenna Connectors

The IAP-92 is designed for use with external antennas. The IAP-93 is equipped with internal antennas.

Before You Begin

FCC Statement: Improper termination of access points installed in the

United States configured to non-US model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or intentional

AI

Pre-Installation Network Requirements

After WLAN planning is complete and the appropriate products and their placement have been determined, the Aruba controller(s) must be installed and initial setup performed before the Aruba APs are deployed.

For initial setup of the controller, refer to the ArubaOS Quick Start Guide for the software version installed on your controller.

AP Pre-Installation Checklist

Before installing your IAP-92/IAP-93 access point, be sure that you have the following:

 CAT5 UTP cable of required length  One of the following power sources:

 IEEE 802.3af-compliant Power over Ethernet (PoE) source  Aruba AP AC-DC adapter kit (sold separately)

 Aruba Controller provisioned on the network:

 Layer 2/3 network connectivity to your access point

One of the following network services:

Summary of the Setup Process



Successful setup of an IAP-92/IAP-93 access point consists of five tasks, which must be performed in this order:

1. Verify pre-installation connectivity.

2. Identify the specific installation location for each AP.

3. Install each AP.

4. Verify post-installation connectivity.

5. Configure each AP.



violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).

EU Statement: Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide for details on restrictions.

Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User Guide pour les details des restrictions.

Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich Einschränkungen finden Sie im ArubaOS

User Guide.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla ArubaOS User Guide per avere informazioni detagliate sulle restrizioni.

 Aruba Discovery Protocol (ADP)

 DNS server with an “A” record

 DHCP Server with vendor-specific options

It is important that you verify the items listed under AP Pre-Installation

Checklist before you attempt to set up and install an IAP-92/IAP-93.

Aruba Networks, Inc., in compliance with governmental requirements, has designed the IAP-92/IAP-93 access points so that only authorized network administrators can change the settings. For more information about AP configuration, refer to the ArubaOS Quick Start Guide and ArubaOS User Guide.

 When connected to the network, each AP is assigned a valid IP address  APs are able to locate the controller

Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the controller.

Identifying Specific Installation Locations

You can mount the IAP-92/IAP-93 access point on a wall or on the ceiling. Use the AP placement map generated by Aruba’s RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/ interference sources will impact RF propagation and should have been accounted for during the planning phase and adjusted for in RF plan.

Identifying Known RF Absorbers/Reflectors/Interference Sources

Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an AP to its fixed location.

RF absorbers include:

 Cement/concrete—Old concrete has high levels of water dissipation, which

dries out the concrete, allowing for potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking RF signals.

 Natural Items—Fish tanks, water fountains, ponds, and trees  Brick

RF reflectors include:

 Metal Objects—Metal pans between floors, rebar, fire doors, air conditioning/

heating ducts, mesh windows, blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets.

 Do not place an AP between two air conditioning/heating ducts. Make sure

that APs are placed below ducts to avoid RF disturbances.

RF interference sources include:

 Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones)  Cordless headset such as those used in call centers or lunch rooms

Installing the AP

Installation and service of Aruba Networks products should be performed by Professional Installers. Additional antenna and transmit power

AI



Using the Integrated Wall-Mounting Slots

The keyhole-shaped slots on the back of the AP can be used to attach the device upright to an indoor wall or shelf. When you choose the mounting location, allow additional space at the right of the unit for cables.

1. Since the ports are on the back of the device, make sure that you mount the AP is such a way that there is a clear path to the Ethernet port, such as a predrilled hole in the mounting surface.

2. At the mounting location, install two screw on the wall or shelf, 1 7/8 inches (4.7 cm) apart. If you are attaching the device to drywall, Aruba recommends using appropriate wall anchors (not included).

3. Align the mounting slots on the rear of the AP over the screws and slide the unit into place (see Figure 4).

Figure 4 Installing the IAP-92/IAP-93 Access Point on a Wall

information for Professional Installers can be found at https://

support.arubanetworks.com.

If you are installing an IAP-92, be sure to attach the antennas before mounting the AP.

Access points are radio transmission devices and as such are subject to governmental regulation. Network administrators responsible for the configuration and operation of access points must comply with local broadcast

AI

regulations. Specifically, access points must use channel assignments appropriate to the location in which the access point will be used.

Verifying Pre-Installation Connectivity

Before you install APs in a network environment, make sure that the APs are able to locate and connect to the controller after power on. Specifically, you must verify the following conditions:

AP-92_003

Using the Integrated Ceiling Tile Rail Slots

᳝↦᳝ᆇ⠽䋼ໄᯢ

The snap-in tile rail slots on the rear of the AP can be used to securely attach the device directly to a 15/16" wide, standard ceiling tile rail.

Make sure the AP fits securely on the ceiling tile rail when hanging the

AI

device from the ceiling; poor installation could cause it to fall.

1. Pull the necessary cables through a prepared hole in the ceiling tile near where the AP will be placed.

2. If necessary, connect the console cable to the console port on the back of the AP.

3. Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots at approximately a 30-degree angle to the ceiling tile rail (see Figure 5). Make sure that any cable slack is above the ceiling tile.

Figure 5 Orienting the Ceiling Tile Rail Mounting Slots

AP-92_004

4. Pushing toward the ceiling tile, rotate the AP clockwise until the device clicks into place on the ceiling tile rail.

Connecting Required Cables

Install cables in accordance with all applicable local and national regulations and practices.

Ethernet Ports

The RJ45 Ethernet port (ENET) supports 10/100/1000Base-T auto-sensing MDI/ MDX connections. Use these ports to connect the AP to a twisted pair Ethernet LAN segment or directly to an Aruba Controller. Use a 4- or 8-conductor, Category 5 UTP cable up to 100 m (325 feet) long.

The 10/100/1000 Mbps Ethernet port is on the back of the AP. The port has an RJ45 female connector with the pin-outs shown in .

Figure 6 Gigabit Ethernet Port Pin-Out

1000Base-T Gigabit

Ethernet Port

RJ-45 Female Pin-Out

Serial Console Port

The serial console port (Console) allows you to connect the AP to a serial terminal or a laptop for direct local management. This port is an RJ-45 female connector with the pinouts described in Figure 7. Connect this port directly to a terminal or terminal server using an Ethernet cable.

Use a modular adapter to convert the RJ-45 (female) connector on the AP to a DB-9 (male) connector, and connect the adapter to a laptop using an RS-232 cable. See Figure 8 for connector details of the adapter.

Figure 7 Serial Port Pin-Out

Serial

Console Port

Figure 8 RJ-45 (Female) to DB-9 (Male) Modular Adapter Conversion

RJ-45 Female

Direction

Output

Pin-Out

1 2 3

TxD

4 5

GND

RxD

7 8

Input

RJ-45 DB-9

Signal Name

BI_DA+

BI_DA-

BI_DB+

BI_DC+

BI_DC-

BI_DB-

BI_DD+

BI_DD-

RJ-45 Female Pin-Out

Direction

Input

Output

Internal

Connections

TxD

3 4 5

GND

RxD

Function

Bi-directional pair +A Bi-directional pair -A Bi-directional pair +B Bi-directional pair +C Bi-directional pair -C Bi-directional pair -B Bi-directional pair +D Bi-directional pair -D

1 2 3

TxD GND

4 5

GND

RxD

7 8

9 8 7 6

Direction

DB-9 Male

Pin-Out

Input

Output

Ground

5 4

RxD

TxD

2 1

Power Connection

The IAP-92/IAP-93 has a single 12V DC power jack socket to support powering through an AC-to-DC power adapter.

If both POE and DC power are available, the AP uses POE even when there



is not enough POE voltage available to power the AP.

Verifying Post-Installation Connectivity

.The integrated LEDs on the AP can be used to verify that the AP is receiving power and initializing successfully (see Table 1). Refer to the ArubaOS Quick Start Guide for further details on verifying post-installation network connectivity

Table 1 IAP-92/IAP-93 Series LED Meanings

LED Color/State Meaning

PWR Off No power to AP

Green flashing System initializing

Red steady System failed to initial-

Green steady Power on, device ready

ENET (10/100/1000 Mbps)

Off No link

Green on 1000 Mbps link

Amber on 10/100 Mbps link

11A/N Off 5 GHz radio is disabled

Amber 5 GHz radio enabled in

Green 5 GHz radio enabled in

Green flashing 5 GHz Air Monitor or RF

11B/G/N Off 2.4 GHz radio disabled

Amber 2.4 GHz radio enabled in

Green 2.4 GHz radio enabled in

Green flashing 2.4 GHz Air Monitor or

ize, contact TAC

WLAN mode

11n mode

Protect mode

WLAN mode

11n mode

RF Protect mode

Product Specifications

Electrical

 Ethernet:

 1 x 10/100/1000Base-T auto-sensing Ethernet RJ-45 Interfaces  MDI/MDX  IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab

(1000Base-T)

 Power over Ethernet (IEEE 802.3af compliant), 48V DC/350mA (see Figure

6 for pin configuration)

 Power:

 12 VDC power interface, supports powering through an AC-to-DC power

adapter

If a power adapter other than the one provided by Aruba Networks is used in the US or Canada, it should be cULus (NRTL) Listed, with an output



For additional specifications on this product, please refer to the data sheet. The data sheet can be found at www.arubanetworks.com.

rated 12 VDC, minimum 1.25A, marked “LPS” or “Class 2,” and suitable for plugging into a standard power receptacle in the US and Canada.

Proper Disposal of Aruba Equipment

For the most current information about Global Environmental Compliance and Aruba products, see our website at www.arubanetworks.com.

Waste of Electrical and Electronic Equipment

Aruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive

2002/96EC on Waste of Electrical and Electronic Equipment (WEEE).

European Union RoHS

Aruba products also comply with the EU Restriction of Hazardous Substances Directive 2002/95/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment.

Specifically, restricted materials under the RoHS Directive are Lead (including

Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this Directive.

China RoHS

Aruba products also comply with China environmental declaration requirements and are labeled with the “EFUP 10” label shown at the

left.

Hazardous Materials Declaration

䚼ӊৡ⿄

(Parts)

⬉䏃ᵓ

(

PCA Boards)

ᴎẄ㒘ӊ

(

Mechanical Sub-Assemblies)

 ƻ˖

㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼

Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.

 h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7󰵼ޚ㾘ᅮⱘ䰤䞣㽕∖Ǆ

Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard.



ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼Ǆ

This table shows where these substances may be found in the supply chain of electronic information

ℸ󰵼ᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳ󰵼ᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ ՟བ⬉∴ܗ῵ഫ䌈೼݊ѻકϞ ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟ݠЁ᠔㾘ᅮⱘᴵӊϟᎹ԰

The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here. The Environment- Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual.

䪙

3E∲+J䬝&G

hƻ ƻ ƻ ƻ ƻ

products, as of the date of sale of the enclosed product.

᳝↦᳝ᆇ⠽䋼៪ܗ㋴(Hazardous Substance)

݁Ӌ䫀



&U



SJ/T11363-2006



໮⒈㘨㣃

3%%

󰵼ޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟǄ

໮⒈Ѡ㣃䝮

3%'(

Safety and Regulatory Compliance

Aruba Networks provides a multi-language document that contains countryspecific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded from the following location: www.arubanetworks.com/safety_addendum

The device will be electronically labeled and the FCC ID will be displayed via the controller WebUI under the About menu.

Aruba access points must be installed by a professional installer. The professional installer is responsible for ensuring that grounding is available

AI

and it meets applicable local and national electrical codes.

RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 7.87 inches (20cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use.

EMC Compliance and Warning Statement

 IEC 60601-1-2: 2007  EN 60601-1-2: 2007

This equipment has been tested and found to comply with the limits of the standard for medical devices, IEC 60601-1-2:2007. The unit also complies with the requirements of EN 60601-1-2:2007, providing the presumption of compliance to the European Union’s Medical Device Directive 2007/47/EC. The limits are designed to provide reasonable protection against harmful interference in a typical medical installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in accordance with the manufacturer’s instructions may cause harmful interference to other devices in the vicinity. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes interference with other devices, which may be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

 Reorient or relocate the device receiving the interference.  Increase the separation between the equipment.  Connect the equipment into an outlet on a circuit different from that to which

the other device(s) are connected.

 Consult the manufacturer or field service technician for help.

The Models IAP-92 and IAP-93 do not have an Applied Part as defined in IEC 60601-1. The protection against electric shock is Class ll.

Device is not protected against ingress of liquids and has a protection class of IPX0 as defined by IEC 60601-1 and IEC 60529. Equipment not suitable for use in the presence of flammable mixtures.

The unit is considered “Continuous Operation” equipment as defined by IEC 60601-1.

Power Consumption – 48 VDC 802.3af power over Ethernet or 12VDC, 1.25A for external AC supplied power (adapter sold separately); Maximum power consumption - 10W.

Mechanical Dimensions: 120mm x 130mm x 55mm; 255g.

IAP-92 and IAP-93 Wireless

Access Point

Installation Guide

Contacting Aruba Networks

Table 1

Web Site Support

Main Site http://www.arubanetworks.com

Support Site https://support.arubanetworks.com

Software Licensing Site https://licensing.arubanetworks.com/login.php

Wireless Security Incident Response Team (WSIRT)

Americas and APAC Support Email support@arubanetworks.com

EMEA Support Email emea.support@arubanetworks.com

WSIRT Email Please email details of any security problem found in an Aruba product.

Table 2

Telephone Support

Aruba Corporate +1 (408) 227-4500

FAX +1 (408) 227-4550

© 2010 Aruba Networks, Inc. AirWave®, Aruba Networks®, Aruba Mobility Management System®, Bluescanner, For Wireless That Works Wireless Workplace Is Now Open For Business, and The Mobile Edge Company Networks, Inc. All rights reserved. All other trademarks are the property of their respective owners.

, Mobile Edge Architecture, People Move. Networks Must Follow., RFProtect®, The All

Open Source Code

Certain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open Source Licenses. The Open Source code used can be found at this site:

http://www.arubanetworks.com/open_source

Legal Notice

The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those vendors.

Warranty

his hardware product is protected by the Aruba Limited Lifetime warranty. Altering this device (such as painting it) voids the warranty.

www.arubanetworks.com 1344 Crossman Avenue Sunnyvale, California 94089 Phone: 408.227.4500

Fax 408.227.4550

IAP-92 and IAP-93 Wireless Access Point | Installation Guide Part Number 0510863-01 | January 2011

http://www.arubanetworks.com/support/wsirt.php

wsirt@arubanetworks.com

are trademarks of Aruba