Hettich AxisDrive IPS, AxisDrive IPS RF Operating And Mounting Instructions Manual
Operating and mounting instructions
AxisDrive
(Original)
Operating and Mounting Instructions
according to EC Machinery Directive 2006/42/EC,
Appendix VI for the Incomplete Machine
Double drive for adjustment of comfort beds
for use at home
Type: AxisDrive
Produced for: Hettich Franke GmbH & Co. KG
Hinter dem Ziegelwasen 6/1
72336 Balingen
Year of build: 2016
Preface
Warning
Read these operating and mounting instructions
with care to acquire thorough knowledge
regarding the double drive and how to mount it.
Mount the double drive according to these
instructions to prevent injury and damage to the
double drive. Do not install the double drive based
on your assumptions.
Keep these operating and mounting instructions
at hand and check them if you are uncertain
about how to perform any procedure.
Date / status: 2016-02-03
The operating and mounting instructions are a
separate part of the overall documentation.
The overall documentation must be made
available to the mounting, operating and
maintenance staff.
Contact:
Hettich Franke GmbH & Co. KG
Hinter dem Ziegelwasen 6/1
72336 Balingen
Copyright for the operating and mounting instructions
© 2016 by Hettich Franke GmbH & Co. KG
The copyright in these operating and mounting instructions
shall remain with Hettich Franke GmbH & Co. KG.
These operating and mounting instructions are intended for
the mounting staff. They contain technical provisions and
drawings that must not be wholly or partially reproduced,
distributed or used or disclosed to others for competitive
purposes without authorisation.
2
2
Table of Contents
Subject Page
Preface 2
Table of Contents 3
List of Figures 4
1. Introduction 5
1.1 Notes on signs, symbols and marks 5
1.2 Notes for the operator 6
2. General 7
2.1 Intended use 7
2.2 Foreseeable misuse 7
2.3 Scope of delivery 8
2.4 Liability 8
3. Safety 9
3.1 Safety notes for the user company 10
3.2 Safety notes for the operating staff 10
3.3 Nameplate 11
4. Description of the Product 12
4.1 Technical data 12
4.2 Device components 12
4.2.1 Dimensions of the housing and handset / transmitter 13
4.2.2 Dimensions of the motor hook / fittings 13
5. Transport and Mounting 14
5.1 Transport 14
5.2 Mounting 14
5.2.1 Installing the double drive and handset / transmitter 15
5.2.2 Installing the Stress relief 15
5.2.3 Electrical connection 16
5.2.4 Connection of the block battery 16
6. Commissioning 17
6.1 Initial commissioning 17
6.1.2 Connecting the handset / transmitter 18
6.1.3 Connecting the power supply cable 18
7. Operation 19
7.1 Basic functions 19
7.1.1 Commissioning the AxisDrive IPS 20
7.1.2 Commissioning the AxisDrive IPS RF 20
7.2 Emergency lowering functions 21
8. Troubleshooting 22
8.1 Safety notes 22
8.2 Faults 23
8.2.1 Possible faults and removal 23
9. Maintenance and Servicing 24
9.1 Maintenance 24
9.2 Care and cleaning 24
10. Decommissioning 25
11 Disposal 26
11.1 Environmental protection 26
11.2 Scrapping 27
12. EC Declaration of Incorporation 28
3
3
List of Figures
Figure Page
Fig. 1: AxisDrive IPS / IPS RF 8
Fig. 2: Handset cable 8
Fig. 3: Transmitter 8
Fig. 4: Nameplate 11
Fig. 5: Boxspring bed 12
Fig. 6: Slatted bed frame 12
Fig. 7: Sliding covers 12
Fig. 8: Dimensions AxisDrive IPS 13
Fig. 9: Dimensions AxisDrive IPS RF 13
Fig. 10: Dimensions handset cable 13
Fig. 11: Dimensions transmitter 13
Fig. 12: Position of motor hooks / fittings for mot. adjustment 13
Fig. 13: Disassembly of the sliding covers 15
Fig. 14: Mounting at the slatted bed frame 15
Fig. 15: Stress relief 15
Fig. 16: Block battery 16
Fig. 17: Key assignment remote control 19
Fig. 18: Commissioning AxisDrive IPS 20
Fig. 19: Commissioning AxisDrive IPS RF 20
4
4
1. Introduction
1.1 Notes on signs, symbols and marks
The operating and mounting instructions are to make it easier
for you to get to know the double drive and to use its
intended applications.
The operating and mounting instructions contain important
information for safe and professional mounting of the double
drive. Observing them will help avoid dangers, reduce repair
costs and downtimes, and to increase reliability and service
life.
Present national provisions on accident prevention and
environmental protection are also applicable.
The operating and mounting instructions must be read and
used by every person who is charged with work at the
components,
such as:
Mounting
Operation
including troubleshooting in the
scope of work, maintenance, disposal
Maintenance
Servicing, inspection, repair and
Transport
The safety notes in the operating and mounting instructions
are structured as follows:
Danger
Danger!
This danger note indicates a directly dangerous
situation that will lead to death or severe injury
if the safety measures are not observed.
Warning
Warning!
This danger note indicates a potentially
dangerous situation that may lead to death or
severe injury if the safety measures are not
observed.
Caution
Caution!
This danger note indicates a potentially
dangerous situation that may lead to minor or
light injury if the safety measures are not
observed.
Note
This note indicates possible property damage or
a process of special interest / importance that
may arise if the safety measures are not
observed.
5
5
1. Introduction
1.2 Notes for the operator
In addition to these operating and mounting instructions and
the rules on accident prevention that are binding in the
country of use or at the site of use, the recognised technical
rules for safety-compatible and professional work must be
observed as well.
The operator of the double drive must not perform any
attachments or conversions to modifications of the unit that
may impair safety without the manufacturer's approval.
Components used must comply with the technical
requirements specified by the manufacturer.
Only deploy trained or instructed staff and clearly specify the
responsibilities of staff for operation, maintenance and repair.
Note
Always subject your end product (comfort bed /
slatted bed frame) to a risk assessment, so that
you will be able to react to possible residual
dangers, e.g. by constructional measures or by
information in the operating instructions and /
or by safety notes on your product).
6
6
2. General
2.1 Intended use
Warning
Warning!
This danger note indicates a potentially
dangerous situation that may lead to death or
severe injury if the safety measures are not
observed.
This double drive is only meant for mounting and subsequent
use on beds, slatted bed frames and/or boxspring beds for
lifting and lowering the head and foot sections. The double
drive thus is only intended for this purpose.
Any other or additional use, e.g. outside of the technical
specifications (see chapter 4.1) is deemed misuse and not
intended.
2.2 Foreseeable misuse
Warning
Misuse may cause dangers!
The double drive is not permitted for use in
medical areas (e.g. hospitals, pensioners' or
nursing homes, etc.).
Foreseeable misuse shall specifically include
the following:
Operation in moist environments or outdoors
Operation in environments with flammable or
explosive gases or steams
Operation outside of the maximum forces
indicated on the name plate
Operation without a bed frame, directly on
the
floor
To lift loads, etc.
For any other use that is not intended use
The items named are some of the residual dangers that may
occur in spite of prohibitions and that may endanger the
health of employees.
The safety requirements that are defined in the operating
safety regulations must be observed by the operator.
Violations will lead to exclusion of any liability of the
manufacturer. When any persons who are not authorised to
do this by Hettich Franke manipulate the system, all warranty
and liability claims regarding the double drive will also expire.
This shall also apply in case of improper installation or
removal, improper use, unprofessional treatment and wrong
operation, or if Hettich Franke is not at fault for damage for
any other reasons.
7
7
2. General
2.3 Scope of delivery
The following parts may be assembled as required for
installation of a comfort bed / slatted bed frame:
Fig. 1: AxisDrive IPS / IPS RF
The following accessories are available for the system:
2.4 Liability
Defects must only be removed by qualified staff.
The manufacturer's liability shall be limited to damage
caused at intended use. The manufacturer shall not be
liable for safety defects that are not recognisable yet
according to the current state of the art.
Violations:
of safety notes for the operating staff
of the notes regarding special dangers
of the prohibition of independent conversion and
modification
of the use of components not released by the
manufacturer
shall exclude liability of the manufacturer for
consequences.
Fig. 2: Fig. 3:
Handset cable Transmitter
8
8
3. Safety
The operating and mounting instructions use the following
marks for danger points (purs. to ASR A1.3):
Danger
Danger to children!
Keep children away from packaging and
mounting material. Among others, there is a
danger of suffocation and danger of swallowing
of small parts.
This device may be used by children at least 8
years old and by persons with reduced physical,
sensory or mental skills or lack of experience, as
long as they are supervised or instructed in the
safe use of the device and understand the
resulting dangers. Children must not play with
the device. Cleaning and user maintenance
must not be performed by children without
supervision.
Danger
Danger from electric shock!
There is a danger to life from electric shock at
improper work at live parts!
Warning
Danger of injury!
There is a danger of injury from moving parts.
Before performing any work at the double drive,
disconnect the power supply and secure the
power supply cable against accidental activation!
Caution
Warning of tripping danger!
Ensure that there are no loose cables in the
walking area on the floor and in the air. This
prevents tripping danger.
Caution
Warning of hand injury!
There is the danger of hands being crushed or
otherwise damaged.
Never reach into moving parts!
Start moving the double drive only when no
persons are present in the danger area anymore!
Work at electrical equipment must only be
performed by authorised electricians!
Warning
Danger
Danger of fire!
Observe the relevant provisions on fire
protection. In case of fire, disconnect the
double drive from the mains by the mains plug.
The mains plug therefore must be accessible at
all times in operation, so that it can be pulled
from the socket quickly in emergency.
9
Warning of crushing danger!
Never place any objects or body parts
between the adjusted head or foot section.
Warning
Warning of overload!
Avoid electrical and mechanical overload, as well
as permanent operation of the double drive for
more than two minutes.
Do not stand on the slatted bed frame.
Do not sit on the raised head or foot section.
The slatted bed frame is not designed for this
stress.
Use the slatted bed frame only for its intended
purpose and do not overload it.
Loading...