Hestan KRD485GDNG, KRD484GDLPWH, KRD484GDLPGG, KRD485GDNGWH, KRD484GDLPYW User Manual

...

INDOOR COOKING

Dual-Fuel Range

KRD

Use & Care Manual

CAUTION

NOTICE

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING

PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

1. Do not try and light any appliance.

2. Do not touch any electrical switch.

3. Do not use any phone in your building.

4. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

5. If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE INSTALLING OR USING YOUR APPLIANCE TO REDUCE THE RISK OF FIRE, BURN HAZARD, OR OTHER INJURY. KEEP THIS MANUAL FOR FUTURE REFERENCE.

SAFETY DEFINITIONS

THIS INDICATES THAT DEATH OR SERIOUS INJURY MAY OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING.

THIS INDICATES THAT MINOR OR MODERATE INJURY MAY OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING.

THIS INDICATES THAT DAMAGE TO THE APPLIANCE OR PROPERTY MAY OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING.

INSTALLER: LEAVE THIS MANUAL WITH THE OWNER OF THE APPLIANCE. HOMEOWNER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

TIP OVER HAZARD

A child or adult can tip over a range and be killed. Check installation of the anti-tip device per the Installation Manual. Do not operate the range without this device in place. Check engagement of anti-tip device if range is moved, such as when cleaning behind the unit. To check engagement, carefully tip the range forward while pulling from the rear of the unit. The range should not move more that 1 inch [2.5cm]. Failure to follow these instructions can result in death or serious burns to children and adults. To reduce the risk of burns, do not move this appliance while hot.

Message from Hestan

Hestan’s award-winning culinary innovations and purpose-built features reinvented the restaurant kitchen and redefined culinary experience in some of America’s most acclaimed restaurants. Hestan now takes this performance from the back of the house and puts it front and center in yours. Thoughtfully designed and meticulously built, Hestan will serve you beautifully for years to come.

Hestan is the only residential brand born from the dreams and demands of professional chefs. From ranges to refrigeration, every detail is designed to deliver the performance and reliability expected in a restaurant – now available for you.

We appreciate you choosing Hestan, and we promise to deliver the very best to you.

Welcome to Hestan

TABLE OF CONTENTS

3 SAFETY PRECAUTIONS - BEFORE YOU BEGIN 8 MODEL NUMBERS 9 RATING LABEL 9 REGULATORY / CODE REQUIREMENTS 10 GETTING STARTED WITH YOUR APPLIANCE 17 USING THE RANGETOP 19 USING THE GRIDDLE 20 USING THE OVEN 24 OVEN CONTROLS 44 ADDITIONAL ITEMS 44 CARE & MAINTENANCE 49 TROUBLESHOOTING GUIDE 50 PARTS LIST 50 SERVICE 51 LIMITED WARRANTY

(SOME MODELS)

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

When properly cared for, your Hestan appliance will provide safe, reliable service for many years. When using this appliance, basic safety practices must be followed as outlined below.

INSTALLER: Please leave these Installation Instructions with the owner. OWNER: Please retain these Installation Instructions for future reference. This range is designed for residential use only. It is NOT designed for installation in manufactured

(mobile) homes or recreational park trailers. Do NOT install this range outdoors.

ELECTRICAL SHOCK HAZARD

Disconnect power before installing or servicing appliance. Before turning power ON, be sure all controls are in the OFF position. Failure to do so can result in electrical shock or death.

ELECTRICAL GROUNDING

This appliance must be grounded. Grounding reduces the risk of electric shock in the event of a short circuit. Read the ELECTRICAL CONNECTIONS section of the Installation Manual for complete instructions.

This appliance is equipped with a 4-prong grounding plug for your protection against shock hazard and should be directly plugged into a properly grounded receptacle. Do not cut or remove the grounding prong from this plug.

CAUTION

SHUTOFF VALVE

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

(CONTINUED)

ELECTRICAL SUPPLY

This appliance must be connected to a dedicated circuit, 240 VAC, Single Phase, 60 Hz, with a current rating as shown in the model number listing on pg. 8. Have the installer show you where the electric circuit breaker is located so you know how to shut off the power to this appliance. It is the responsibility of the user to have the appliance connected by a licensed electrician in accordance with all local codes, or in the absence of local codes, in accordance with the National Electrical Code. Read the ELECTRICAL CONNECTIONS section of the Installation Manual for complete details.

GAS SUPPLY

A gas shut-off valve must be located in an easily accessible location for servicing of the range. Make sure all users of the range know where this shut-off is located, and how to shut off the gas.

The type of gas should be verified prior to installation and operation of this appliance. It is the responsibility of the user to have the appliance connected by a licensed plumber in accordance with all local codes, or in the absence of local codes, in accordance with the National Fuel Gas Code.

When connecting to LP gas, verify the tank is equipped with its own high pressure regulator. The pressure of the gas supplied to the appliance must be 11-14 inch WC [2.74-

3.48 kPa]. Consult the Installation Manual for details on gas type, gas pressure, connection and leak testing instructions, etc.

Read the GAS CONNECTIONS section of the Installation Manual for complete details.

GAS

SUPPLY

IN OPEN POSITION

APPLIANCE

CONVERSION KITS

In the event your Hestan appliance needs to be converted from NG to LP, or vice-versa, you will need to contact Hestan Customer Service to arrange a service call. This conversion should only be performed by a qualified technician.

HIGH ALTITUDE KITS

If you live in a high altitude area, 2,000 ft. [610 m] or more above sea level, your appliance may require different orifices for proper combustion and performance. You will need to contact Hestan Customer Service to arrange a service call. High Altitude kits must be installed by a qualified technician. Please have your model and serial number information ready when you call.

BACKGUARD

Your Hestan range is supplied at the factory with an Island Trim backguard. See Table 1 in the APPENDIX section of the Installation Manual for other backguard options available from your Hestan dealer, or visit www.hestanhome.com. Selection of the appropriate backguard depends on the installation location and adjacent materials, and the type of vent hood to be used. Installation instructions are included with the backguard kit. A LOW OR TALL BACKGUARD IS REQUIRED WHEN INSTALLING THE RANGE AGAINST A COMBUSTIBLE SURFACE - THE ISLAND TRIM IS NOT SUITABLE.

The top of the backguard serves as an exhaust for the oven when in operation, and as an exhaust vent to remove heat from under the rangetop section of the range as well. DO NOT BLOCK or obstruct the top of the backguard. DO NOT touch the top of the backguard during appliance operation as it may get hot. Allow sufficient time to cool before touching or cleaning this area. DO NOT position plastic or other heat-sensitive items nearby which could melt or burn.

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

CAUTION

(CONTINUED)

VENTILATION REQUIREMENTS

It is strongly recommended that this appliance be installed with a Hestan vent hood. Hestan vent hoods have been matched up to the BTU output of the range. Due to the high heat output of this range, it is very important that the hood and ductwork installation meets local building codes and is installed by a qualified technician.

Do not use a down-draft style ventilation system. Do not mount a microwave oven/ventilator combination above the range. These types of units do

not have sufficient airflow to remove the high heat output of this range and were not tested with this type of appliance.

Consult the Installation Manual for further details.

CONSULT WITH YOUR HESTAN DEALER ON SELECTING THE APPROPRIATE VENT HOOD FOR YOUR HESTAN APPLIANCE.

IN CASE OF POWER OUTAGE

All the control knobs must be in the OFF position to prevent unintended operation at power up. To ensure customer safety in the event of a power failure, the range will display an error message when the power is restored unless all the knobs are in the OFF position. Set all the knobs to OFF to clear the error message.

DO NOT ATTEMPT TO USE THE RANGE DURING A PROLONGED POWER FAILURE. Although the top burners can be manually lit, they should be used ONLY WHILE BEING ATTENDED BY THE USER. On low burner settings, if the flame were to go out, a dangerous accumulation of gas could result in an explosion.

CHILD SAFETY

IT IS THE RESPONSIBILITY OF THE PARENTS OR GUARDIANS TO ENSURE CHILDREN ARE INSTRUCTED IN THE SAFE USE OF THIS APPLIANCE. Do not allow children to use this appliance without adult supervision. Do not allow children to play in or around the appliance, even when not in use. Items of interest to children should not be stored in or on the appliance, in cabinets above, or on the backguard of the appliance. Children climbing on the appliance could be seriously injured.

BURN HAZARD - All parts of the range can get very hot during operation. The oven door glass and areas surrounding the door get very hot, especially during self-cleaning operations. Do not let children touch the appliance while in operation. Failure to observe these instructions may result in severe burns or injury.

TECHNICAL SAFETY

Installation and service on this appliance must be performed by a qualified appliance installer, or a Hestan authorized service technician. Do not repair or replace any part of the appliance unless specifically instructed to do so. Defective parts must only be replaced with genuine Hestan parts. Contact Hestan Customer Service for inquiries or to arrange a service call.

The appliance must be disconnected from the power and gas supply during any service or maintenance work.

Do not carry or lift the range by the oven handle. The range can only lifted from the sides.

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

(CONTINUED)

USER SAFETY

BURN HAZARD - All parts of the range can get very hot during operation. The oven door glass and areas surrounding the door get very hot, especially during self-cleaning operations. Do not touch the appliance while in operation. Failure to observe these instructions may result in severe burns or injury. Use pot holders / gloves to protect yourself when placing food in the oven, adjusting the racks, etc.

The upper broil element is housed behind a special glass panel, and the lower bake element is hidden beneath the floor of the oven cavity. The convection element is hidden behind the fan at the rear of the oven cavity. All these heating elements may be hot, even though they are not glowing. During or after cooking, allow sufficient time for all surfaces to cool.

Use only dry or heat-resistant pot holders / gloves. Using moist or damp potholders can result in steam burns. Do not substitute dish towels or similar items for potholders. These items could come in contact with hot surfaces and ignite.

Avoid wearing loose-fitting garments or long sleeves while cooking. They could ignite. For personal safety, wear proper apparel while using the appliance. Some synthetic fabrics are highly flammable and should not be worn while cooking.

Open the oven door slowly to allow heat and steam to escape before placing or removing food from the oven. Keep your face away from the opening to avoid injury.

For safety considerations, NEVER use this appliance as a space heater to heat or warm the room. Doing so may result in carbon monoxide poisoning and overheating of the oven.

Do not use the oven as a storage space. The high temperatures could also ignite flammable objects nearby.

NEVER cover any slots, holes, or passages in the oven bottom or cover an entire oven rack with materials such as aluminum foil. Doing so blocks air flow through the oven and may cause carbon monoxide poisoning. Aluminum foil linings may also trap heat, causing a fire hazard. Do not use aluminum foil to line the surface burners. Doing so may result in a risk of electric shock, or fire.

Do not allow anyone to climb, stand, step on, lean against, or sit on any part of the appliance, especially the oven door. This may result in damage to the appliance, or personal injury.

FIRE SAFETY

To reduce the risk of a fire, do not leave surface burners unattended at high settings. Boil-overs could smother the flames and igniter, which would allow un-burned gas to escape into the room, which could result in an explosion.

Always turn on the ventilation hood when cooking. Clean vent hood grease filters frequently grease should not be allowed to accumulate on the fan or filters.

Use the appropriate pan size for the burner being used. For safety considerations, adjust the flame size so they do not travel up the sides of the pan.

Keep the appliance area clear and free from combustible materials, gasoline, and other flammable vapors and liquids. NEVER store flammable liquids and materials in, above, or on the range, or near cooking surfaces. Do not obstruct the flow of combustion and ventilation air of the appliance.

ALWAYS have a working smoke detector near the kitchen. ALWAYS have an appropriate dry-chemical fire extinguisher nearby. Smother fire or flames using

the lid of the utensil (pot or pan), a cookie sheet or metal tray. Then shut off the burner. Use an

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

extinguisher, or baking soda if the fire is small and relatively contained. DO NOT USE WATER ON A GREASE FIRE. Doing so may result in spreading the fire elsewhere.

NEVER pick up a flaming pan. You may spill the grease on yourself and be severely burned. If accessible, turn off the ventilation hood during a fire, but do not reach through the flames to do

this. In the event of personal clothing or hair catching fire, drop and roll immediately to smother the

flames. Seek medical attention if necessary. Do not hang articles from any part of the appliance or place anything against the oven door. Some

fabrics are highly flammable and could ignite.

(CONTINUED)

IF THE FLAMES DO NOT GO OUT - EVACUATE AND CALL THE FIRE DEPARTMENT.

SAFETY DURING CLEANING

Only clean the appliance as directed in the CLEANING & MAINTENANCE section of this manual. Do not use a steam cleaner to clean the oven or any part of the range. Steam could penetrate into

electrical components and cause a short circuit and/or shock hazard. Do not use abrasive cleaners, hard objects such as brushes or scrapers, or sharp metal tools to clean

the door glass. Scratches could cause the glass to shatter. Heavy food debris should be removed before running the self-clean cycle. Remove all oven racks,

broiler pans, utensils, temperature probes, etc. from the oven before self-clean. Removal of the left & right ladder racks inside should also be done as they will discolor from the intense heat.

Do not rub, disturb or damage the cloth-braided door gasket. If the gasket is damaged, it will need to be replaced.

Do not pour cold water onto hot surfaces inside the oven. The steam could cause serious burns. The sudden temperature change could also distort the metal surfaces inside the oven resulting in cracks in the enamel.

Use only a small toothbrush to clean the burner ports and igniter of the surface burners. Do not insert sharp objects or scratch the burner ports.

Wait until the appliance is completely cool before using any aerosol-type cleaners. Many of these cleaners use flammable propellants which could ignite in the presence of heat.

PROPER USAGE

Do not let food sit in the oven for more than one hour before or after cooking. Doing so may result in food poisoning or illness.

Do not heat unopened containers (cans) in the oven. Pressure may build up causing the container to explode, resulting in damage to the oven, or personal injury.

Always place the oven racks at the desired height before cooking. If the racks must be moved when hot, use potholders to move them and use caution to avoid touching any heating elements.

Only certain types of glass, heatproof glass-ceramic, earthenware, or other glazed utensils are suitable for use on the surface burners. However, these types of materials may break with sudden temperature changes. Use only on low or medium heat settings, and according to their manufacturers’ directions.

Bakeware, such as large casserole pans, cookie sheets, etc. should not be used on the surface burners. Large griddle plates that span across 2 burners should be used with care and on medium to low flame settings to avoid a build-up of heat which could distort the grates or the burner bowl.

Always position the handles of pot and pans so they do not extend over adjacent work areas or over the edge of the rangetop. This is to avoid knocking over hot contents which could burn you, or result in a fire.

Do not use pots or pans on the griddle (if equipped).

MODEL NUMBERS

RANGE MODELS

MODEL NO. DESCRIPTION

KRD304-NG / -LP 30” DUAL-FUEL RANGE WITH 4 BURNERS 40 Amp

KRD365-NG / -LP 36” DUAL-FUEL RANGE WITH 5 BURNERS 40 Amp

KRD364GD-NG / -LP 36” DUAL-FUEL RANGE WITH 4 BURNERS & 12” GRIDDLE 40 Amp

KRD485GD-NG / -LP 48” DUAL-FUEL RANGE WITH 5 BURNERS, 2 OVENS, & 12”GRIDDLE 50 Amp

KRD484GD-NG / -LP 48” DUAL-FUEL RANGE WITH 4 BURNERS, 2 OVENS, & 24”GRIDDLE 50 Amp

CIRCUIT BREAKER REQUIRED

KRD304

KRD485GDKRD365

KRD364GD

KRD484GD

RATING LABEL

The rating label contains important information about your Hestan appliance such as the model and serial number, gas type and manifold pressure, electrical rating, the BTU rating for each burner type, and the minimum installation clearances.

The rating label is located in one of two places, as shown in the figures on this page.

If service is necessary, contact Hestan Customer Care with the model and serial number information shown on the label.

RATING LABEL

REGULATORY / CODE REQUIREMENTS

Installation of this cooking appliance must be made in accordance with local codes. In the absence of local codes, this unit should be installed in accordance with the National Fuel Gas Code

Z223.1/NFPA 54

Handling Code All Electrical Components must be electrically grounded in accordance with local codes or in the

absence of local codes with the National Electrical Code

CSA C22.1

STATE OF MASSACHUSETTS Massachusetts requires all gas be installed using a plumber or gas fitter carrying the appropriate Massachusetts license. All permanently installed natural gas or propane installations require a T-handle type manual gas valve be installed in the gas supply line to this appliance. Flexible gas connector must not be longer than 48” [1.2 m].

CALIFORNIA PROPOSITION 65 - WARNING

WARNING This product can expose you to chemicals including carbon monoxide, which is

known to the State of California to cause birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

, Natural Gas and Propane Installation code

B149.2

CSA B149.1

ANSI/NFPA 70

, or Propane Storage and

, or Canadian Electrical code

ANSI

GETTING STARTED WITH YOUR APPLIANCE

COMPONENT IDENTIFICATION

Use the images below to familiarize yourself with the various parts of the rangetop and oven.

KRD30, KRD36

1. Island Trim Backguard (included)*

2. Sealed Dual-Flow Burner

3. Burner Grate

4. Griddle (GD models)

5. Control Knobs

6. Touch-screen Display

7. Main Oven

8. Oven Light Switch

9. Kick Plate

* Low or Tall Backguard ordered separately.

Oven cavity of 30” range, 36” range, main oven cavity of 48” range

MODEL KRD364GD SHOWN

1. Temperature Probe Jack, oven of 36” range

2. 6 Position Ladder Rack

3. Oven Rack (3 included)

4. Fan Cover

5. Broil Element

6. Bake Element (hidden)

7. Temperature Sensor

8. Interior Light (2)

9. Self-Clean Latch

10. Temperature Probe Jack, 30” range, Main Oven of 48” range

GETTING STARTED WITH YOUR APPLIANCE

COMPONENT IDENTIFICATION (CONTINUED)

(CONTINUED)

KRD48

1. Island Trim Backguard (included)*

2. Griddle (GD models)

3. Sealed Dual-Flow Burner

4. Single Flow Power Burner

5. Burner Grate

6. Control Knobs

7. Oven Light Switch - Companion Oven

8. Touch-screen Display - Companion Oven

9. Companion Oven

10. Touch-screen Display - Main Oven

11. Main Oven

12. Oven Light Switch - Main Oven

13. Kick Plate

MODEL KRD485GD SHOWN

Companion Oven cavity of 48” range

1. 6 Position Ladder Rack

2. Oven Rack (3 included)

3. Fan Cover

4. Broil Element

5. Bake Element (hidden)

6. Temperature Sensor

7. Interior Light

GETTING STARTED WITH YOUR APPLIANCE

(CONTINUED)

DUAL-FLOW

BURNER

ROTATE LEFT TO HI TO IGNITE BURNER. ADJUST FLAME AS NEEDED. THERE ARE 3 DETENT POSITIONS AT HI, LOW, AND HI SIMMER FOR EASE OF USE.

ROTATE RIGHT TO SELECT OVEN MODE

LEFT OR

ROTATE LEFT TO MAX TO IGNITE BURNER. ADJUST FLAME AS NEEDED. THERE IS A DETENT AT THE MAX POSITION ONLY.

SINGLE-FLOW

BURNER

ROTATE LEFT OR RIGHT TO SELECT OVEN TEMPERATURE

OVEN MODE

SELECTOR

ROTATE SELECT GRIDDLE TEMPERATURE

GRIDDLE

TEMPERATURE

OVEN

TEMPERATURE

RIGHT TO

MARQUISE™ TOUCH CONTROL HANDLE

GETTING STARTED WITH YOUR APPLIANCE

(CONTINUED)

OVEN RACKS

BURN HAZARD - To help prevent burns, never remove or reposition the oven racks when the oven is in operation, or is cooling.

For safety considerations, NEVER cover any slots, holes, or passages in the oven bottom or cover an entire oven rack with materials such as aluminum foil. Doing so blocks air flow through the oven and may cause carbon monoxide poisoning. Aluminum foil linings may also trap heat, causing a fire hazard.

PLACING THE OVEN RACKS

The oven features ladder racks on the left and right side of the oven with 6 positions. Choose the rack position(s) that result in the best baking, roasting, etc. for your recipe. Rack position #3 (counting from the bottom-up) is the most popular position (vertical center location).

The main oven features racks with full-extension, ball-bearing slides which require minimal maintenance. The companion oven (model KRD48) has traditional wire racks.

ALWAYS REMOVE THE LADDER RACKS, OVEN RACKS, AND ALL OTHER ITEMS FROM THE OVEN DURING THE SELFCLEANING CYCLE.

1. Do not extend the slides - it is easier to install the rack when NOT extended.

While raising the front of the rack slightly, place the rear hook onto the desired ladder rack, then slide the small tab under the ladder as you flatten out the rack.

2. Continue sliding the rack back into the oven.

3. When you reach the front-most hook, slightly lift the rack again to hook over the ladder.

Move the rack a few times in and out to ensure it is locked into the ladders and will not detach.

GETTING STARTED WITH YOUR APPLIANCE

PLACING RACKS - COMPANION OVEN

(CONTINUED)

1. While raising the front of the rack slightly, place the rear lower hooks under the desired side ladder, then slide the rack back approximately 5” [13 cm].

2. Lower the rack until it is level.

3. Continue sliding the rack back into the oven until it is fully inside.

GETTING STARTED WITH YOUR APPLIANCE

BURNER

SEALED BURNERS

Ensure the sealed burner heads are properly installed and seated on the burner base as shown below. There are notches on the burner base and cross ring to help with alignment. The outer burner head features a long slot on the top of the head which aligns with the spark igniter. Assembly of the single-flow burner head is similar.

(CONTINUED)

INNER

BURNER

HEAD

OUTER

BURNER

HEAD

BEAUTY

RING

CROSS

RING

BURNER RING

BURNER

HEAD

BURNER BASE

DUAL FLOW

FIRST TIME OPERATION

Ensure there are no packaging materials inside the oven. Remove any labels or plastic film from the outside of the appliance. Before using your oven for the first time, it will be necessary to run a bake cycle to burn off any manufacturing oils and residues from the oven cavity. This may produce a little smoke and some odor. This is normal and is typical of any new oven when first used. If the smell is strong, remove persons and animals from the kitchen during this period. Open any windows to further vent the odor from the room.

SINGLE FLOW

IGNITER

Install all the oven racks. Turn on your vent hood, and run the oven on BAKE at 500°F [260°C] for 1-1/2 hours. Allow to cool completely before attempting to cook.

DUAL-OVEN MODELS For dual-oven models, perform the same first-time process on the companion oven. This can be done

at the same time as the main oven.

GETTING STARTED WITH YOUR APPLIANCE

(CONTINUED)

BURNER HEADS

If the burner head is not properly positioned, one or more of the following issues may occur:

• Flames too high

• Flames shoot out of the burners

• Burners do not ignite

• Flames are uneven

• Burner emits a gas odor

BURN HAZARD - To prevent burns, do not touch the burner heads or cooking grates when hot. Allow to cool completely. To prevent flare-ups, do not use the burner without all the burner heads in place and properly positioned. Do not use aluminum foil to line the surface burners. Doing so may result in a risk of electric shock, or fire.

BURNER GRATES

See image for proper placement of the burner grates. There are small round embosses at the front and rear of the burner bowl to help align the grates and keep them in position relative to one-another.

GRIDDLE PLATE

(GD models)

See image for proper placement of the Griddle Plate and Grease Tray.

The plate is made of stainless-steel and requires no seasoning. The grease tray has a non-stick coating for easy cleaning.

Always remove the cover before cooking on your griddle.

COVER

GREASE

TRAY

GRIDDLE

PLATE

USING THE RANGETOP

BURNER CONTROL KNOBS

Each sealed burner has its own control knob. The symbol below each knob indicates which burner is controlled by each knob. Push and turn LEFT (counter-clockwise) to HI to ignite the flame, then turn to the desired flame setting.

BURNER TYPES & OUTPUT

This table below indicates the type and output of each sealed burner. Dualflow burners have an inner and outer row of ports, with a simmer function. The single-flow burner (some models) is similar to

DUAL-FLOW

(FRONT)

LOW

SIMMER HI

SIMMER LOW

a commercial burner and features very high output, and a low, but no simmer function.

DUAL-FLOW

(FRONT)

LOW

SIMMER HI

SIMMER LOW

RE-IGNITION

Each sealed burner has its own electronic spark-ignition module with flame-sensing technology and automatic re-ignition capability. If any burner should blow out, the igniter automatically re-lights the burner.

BURNER OUTPUT - NATURAL GAS

OUTPUT (BTU/hr)

23000

4200 1500

500

DUAL-FLOW

(REAR)

LOW

SIMMER HI

SIMMER LOW

OUTPUT (BTU/hr)

15500

4200 1500

500

BURNER OUTPUT - PROPANE

OUTPUT (BTU/hr)

23000

4200 1500

600

DUAL-FLOW

(REAR)

LOW

SIMMER HI

SIMMER LOW

OUTPUT (BTU/hr)

15500

4200 1500

600

SINGLE

FLOW

MAX LOW

GRIDDLE

SINGLE

FLOW

MAX LOW

GRIDDLE 15000

OUTPUT (BTU/hr)

30000

4200

15000

OUTPUT (BTU/hr)

22000

4200

Each burner should light in less than 4 seconds. Once lit, the sparking will stop. On very low simmer, an occasional sparking may occur. This is usually due to a breeze in the room. If an igniter continues to spark even with a flame present, there could be an electrical wiring issue, or some other problem. See the TROUBLESHOOTING section of this manual for more information.

DO NOT touch the burner or the igniters while sparking is occurring. A shock hazard or burns could occur.

MANUAL LIGHTING / POWER FAILURE

THE OVEN AND GRIDDLE CANNOT BE USED DURING A POWER FAILURE. Each sealed burner can be manually lit in the event of a power failure. It is necessary to light each

burner individually. If a power failure occurs WHILE you are using the sealed burners, turn all the knobs to the OFF

position - then light manually with a match or fireplace lighter. Position the match or fireplace lighter at the port nearest the igniter, then turn the knob to HI until

the flame is lit. Wait until the flame has lit all the way around the burner before adjusting the knob to LOW or SIMMER.

IF YOU SMELL GAS, turn all control knobs to OFF - check the precautions listed in the SAFETY section of this manual.

USING THE RANGETOP

(CONTINUED)

FLAME HEIGHT

Proper flame height depends on the size of the pan being used, and the amount of food or liquid in the pan. In other words, don’t use a small pan over a large flame. For safety reasons, control the flame height so that it doesn’t go beyond, or curl up the sides of your pot or pan. This behavior results in poor heating of the contents of the pan, burnt food on the sides of the pan, wasted fuel, etc.

Use a low or medium flame on items that heat slowly, such as glass-ceramic pots.

FLAME CHARACTERISTICS

Light blue flame - Natural gas normal flame Light blue flame with yellow tips - LP gas normal flame Yellow flame - Needs adjustment

If the flame is mostly or completely yellow, check the position of the burner heads again for proper installation, and/or review the FINAL SETUP section of the installation manual for more details.

HOW TO USE YOUR RANGETOP

DUAL FLOW BURNERS The benefit of the dual-flow burner is the amount of control and precision the burners give you,

allowing for the best results possible. Simmer-Low is ideal for heating delicate foods without having the fear of burning, scalding, or

boiling over. Some suggestions include:

• Melting chocolate

• Heating milk or cream

• Melting sugar

• Slow cooking or braising SINGLE FLOW BURNER (some models) Ideal Uses:

• Searing

• Boiling water

• Large stock pots – will allow for even heat distribution under larger surface areas Wok Cooking: We suggest a 14-16 inch [36-41 cm] wok for the best results.

COOKWARE RECOMMENDATIONS

As previously stated on page 7 of the SAFETY PRECAUTIONS section of this manual, bakeware, such as large casserole pans, cookie sheets, etc. should not be used on the surface burners. Large griddle plates that span across 2 burners should be used with care and on medium to low flame settings to avoid a build-up of heat which could distort the grates or the burner bowl.

USING THE RANGETOP

Large stock pots should be staggered when used on the rangetop (see below). Do not cook on aluminum foil or thin, disposable aluminum pans. These can melt. Never let a pot boil dry. If left too long, the pan could melt, or damage the appliance. Use only high-quality pans with metal handles. Some plastic handles could melt from the intense

heat of the burners.

(CONTINUED)

USING THE GRIDDLE

GRIDDLE CONTROL KNOB

The griddle provides a temperature range of 120°F - MAX (approx. 500°F) [49 - 260°C]. Push and turn RIGHT (clockwise) to select the desired temperature for the food you are cooking. A constant orange glow will be seen at the rear vents of the griddle. This is normal.

To avoid injury DO NOT operate the griddle without the griddle plate and grease tray in place. Always remove the cover before use.

(SOME MODELS)

CAUTION

The griddle is very hot after use. Allow sufficient time to cool down before cleaning. DO NOT use metal utensils (pots, pans, etc.) on the griddle plate surface. Be careful not to gouge or

cause deep scratches in the griddle plate surface. DO NOT cut directly on the griddle plate.

FIRST TIME OPERATION Before using your griddle for the first time, the griddle plate and the grease tray should be cleaned

with warm, soapy water and thoroughly rinsed and dried. When you first heat the plate, a little smoke and some odor may be present as any remaining manufacturing oils are burned off. The stainless-steel plate will discolor, from a straw color to a very dark brown or black, depending on what foods you cook on the surface.

USING THE GRIDDLE

(CONTINUED)

COOKING ON THE GRIDDLE

When it comes to using the griddle, there are a few things to keep in mind:

• As time goes on and griddle use increases, discoloration of the griddle plate may happen and is normal.

• When emptying the grease tray, be sure to pour the grease into a proper container for grease disposal, not down the drain. Do not scrape with metal utensils.

It will take some practice to get to know how your griddle performs with certain foods. The table below gives a few recommendations on temperatures.

FOOD ITEM GRIDDLE TEMPERATURE EGGS 300 - 325°F [149 - 163°C] PANCAKES, FRENCH TOAST 400 - 425°F [204 - 218°C] HASH BROWN POTATOES (frozen) 475 - 500°F [246 - 260°C] CHICKEN BREAST (BONELESS) 425 - 450°F [218 - 232°C] BACON, SAUSAGE 450 - 475°F [232 - 246°C] STEAK 1” (25mm) THICK 450 - 475°F [232 - 246°C] HAMBURGER 6 oz (170 g) 450 - 475°F [232 - 246°C]

CLEANING THE GRIDDLE

Read the CLEANING AND MAINTENANCE section of this manual for complete instructions. NEVER flood the hot griddle plate with cold water. This can permanently warp the plate. DO NOT clean any part of the griddle in the Self-Clean Cycle of the oven. Do not put your griddle

plate into the dishwasher, as it will damage your appliance. Wait until the appliance has cooled completely before cleaning.

USING THE OVEN

OVEN FEATURES

The oven in the 30” range, the 36” range, and the main oven of the 48” range have exactly the same features and capabilities. The 48” range’s companion oven does not have a meat probe, and does not include the True Convection and Self Clean modes. The companion oven can be used in any of its modes regardless of the main oven mode, even when the main oven is self-cleaning. Rack suggestions are shown on the following pages.

TIPS AND TRICKS ON HOW TO USE YOUR OVEN

As you begin to use your Hestan Range, it is important to take the time to become familiar with the new settings and the performance of this appliance. Previous ranges may have performed differently than your Hestan – allow some time to adjust.

HOW TO GET THE BEST RESULTS WHEN COOKING IN THE OVEN

• Many recipes give their own rack suggestions, it is best to follow what is suggested by the recipe.

• After a few times of using your new range, you will become more comfortable with rack placements and temperature settings.

• Avoid opening the oven door while cooking. This will prevent heat from escaping and provide the best results.

• Make sure to preheat the oven to the cooking temperature given in the recipe.

USING THE OVEN

• When baking with more than one rack, stagger the pans and give them at least 2” of space between each pan.

(CONTINUED)

• Remember that different bakeware and pans cook and heat differently.

• Light-colored non-stick pans result in golden crust that is tender.

• Dark-colored non-stick pans result in a more brown, crisp crust.

• Generally, when using any Convection mode, it is suggested to reduce the temperature by 25°F [14°C], though this does not apply to all recipes or meats and poultry.

RACK POSITION / BEFORE BAKING

Rack positions depend on the food items you are baking or roasting. Follow the instructions , or your best experience, on which rack position is best to use for a given recipe.

Not all oven racks need to be kept in the oven. If you find you only need one or two racks most of the time, remove the extra rack and store in a convenient location should it be needed later.

ALWAYS place the oven racks at the desired height before cooking. If the racks must be moved when hot, use potholders to move them and use caution to avoid touching any heating elements.

Minimize opening the oven door by using the oven light.

QUICK GUIDE FOR RACK POSITIONS / USES

Choose the rack position(s) that result in the best baking, roasting, etc. for your recipe. Rack position #3 (counting from the bottom-up) is the most popular position (vertical center location).

OVEN MODE SUGGESTED RACK POSITIONS USES PROOF Any Best for allowing bread dough to rise. SELF-CLEAN N/A High-Temperature cleaning cycle, allowing

food debris to burn off.

TRUE CONVECTION

BAKE Center rack #3 Best for baked items. Single-rack cooking or

CONVECTION BAKE

ROAST Center rack #3 Roast less tender cuts of meat such as beef

CONVECTION ROAST

BROIL Rack #5 for steaks, hamburgers,

CONVECTION BROIL

Single Rack: #3 Two Racks: #3 & #5 Multiple Racks: #1 #3 & #5

Single Rack: #3 Two Racks: #3 & #5

Center rack #3 This mode allows for a crisp outside and

etc. 1” (2.5cm) and under. Rack #4 for steaks, hamburgers, etc. thicker than 1” [2.5 cm].

Rack #5 for steaks, hamburgers, etc. 1” (2.5cm) and under. Rack #4 for steaks, hamburgers, etc. thicker than 1” [2.5 cm]

Using air movement produced by the convection fan, this allows for multi-rack cooking.

baking. This is the standard mode for most recipes.

During this mode, a fan in the back of the oven helps air move evenly throughout, allowing for even baking and cooking.

roast. Also good for stews that have to be covered.

a tender and juicy interior on poultry and meats. Ideal for roasting tender cuts of beef lamb poultry.

Broiling meats, fish, and poultry pieces. Direct heat from above only. Pre-heat broil for 3-4 minutes before starting cooking.

Shortens broiling times for thicker cut of meat, fish, poultry. Pre-heat broil for 3-4 minutes before starting cooking.

USING THE OVEN

(CONTINUED)

PRE-HEATING

Many recipes call for a pre-heated oven. Refer to your recipe for instructions. Pre-heating time depends on the Mode and Temperature selected, as well as the number of racks inside the oven.

RACK POSITIONS / USES FOR COMPANION OVEN

The companion oven of the 48” range has the same capabilities as the main oven, with the exception of True-Convection and Self-Clean. The rack position recommendations on the previous page are the same for the companion oven. However, cooking times will probably be different due to the small oven cavity.

APPROPRIATE BAKEWARE / PLACEMENT

Bakeware suitable for use in your Hestan oven are metal, heat-proof glass (Pyrex®), glassceramic, earthenware pottery, etc. Cookie sheets / jelly roll pans with a small lip are also suitable. Thicker sheets or double-sided sheets may increase baking times.

Stagger multiple cake pans as shown here. Leave approximately 2” [5 cm] space between all pans and oven walls to allow for hot air circulation inside the oven.

MEAT PROBE

The meat probe only works in the following modes: Bake, Convection Bake, Roast, Convection Roast, True Convection.

The probe measures between 115 - 185°F [46 - 85°C].

In the 36” oven, the probe inserts into a jack on the upper LEFT side of the oven cavity.

In the 30” oven (KRD30, main oven of KRD48), the probe inserts into a jack on the upper RIGHT side of the oven cavity.

To avoid damaging the probe, do not insert it into frozen meats, or try to force it into your food. The probe should not touch any part of the cooking vessel or the oven. For best results with most meats, the probe should be inserted into the thickest portion of the meat. Ensure the probe tip does not touch bone or fat to get the most accurate internal temperature readings. For poultry, the probe should be inserted into the thickest part of the thigh, or breast.

Use only the probe shipped with the appliance. Use only genuine Hestan spare parts if you need a replacement.

When the probe temperature reaches the set temperature, the cooking mode will stop and the oven will shut off. An audible alert will sound a total of 3 times at 1 minute intervals, or until the user cancels the alert and is prompted to turn both control knobs to OFF.

PROBE - 36” OVEN SHOWN

USING THE OVEN

(CONTINUED)

COOKING WITH THE OVEN

The following pages will help you with the various oven controls. Your recipe will guide you on which cooking modes are best. However, food safety (handling, cooking, storage) is very important in preventing food-borne illness. The table below are recommendations to keep you and your family safe.

FOOD ITEM SAFE MINIMUM INTERNAL TEMPERATURES GROUND MEATS (BEEF, VEAL, LAMB, PORK) 160°F [72°C] BEEF, VEAL, LAMB ROAST, STEAKS, CHOPS Medium Rare - 145°F [63°C]

Medium - 160°F [72°C] Well Done - 170°F [77°C]

PORK ROAST, STEAKS, CHOPS Medium - 160°F [72°C]

Well Done - 170°F [77°C]

HAM Un-cooked - 145°F [63°C]

Reheat cooked hams packaged in USDAinspected plants to 140 °F [60°C]

and all others to 165 °F [74°C] GROUND CHICKEN/TURKEY 165°F [74°C] WHOLE CHICKEN/TURKEY 180°F [82°C] POULTRY BREAST, ROASTS 165°F [74°C] POULTRY THIGHS & WINGS 165°F [74°C] STUFFING (cooked alone) 165°F [74°C] EGG DISHES 160°F [72°C] FISH & SHELLFISH 145°F [63°C] LEFTOVERS 165°F [74°C] CASSEROLES 165°F [74°C]

• Safe minimum internal temperatures per US Dept. of Agriculture Food Safety & Inspection Services guidelines.

OVEN CONTROLS

DISPLAY LAYOUT / KNOB ICONS

30”, 36” Oven, Main Oven of 48” Range

TOUCH SCREEN

OVEN MODE SELECT OVEN TEMPERATURE

True Convection

Bake

Convection Bake

Roast

Broil

Convection Broil

Proof

Self Clean

Convection Roast

OVEN CONTROLS

Roast

TIMER

1:15

DISPLAY LAYOUT / KNOB ICONS - COMPANION OVEN

(in 48” Range only) Some functions and settings are only performed from the main oven display, such as Sabbath. The

companion oven display does not offer the “advanced” menu.

(CONTINUED)

BACK

MINUTE

TOUCH SCREEN

Bake

Convection Bake

Roast

Convection

Broil

Convection Broil

Proof

COMPANION OVEN TEMPERATURECOMPANION OVEN MODE SELECT

OVEN CONTROLS

(CONTINUED)

DISPLAY ACTIVATION

When inactive, the display will be dark. Turning any control knob, or touching anywhere on the screen for 2 or more seconds will activate the display. After more than 1 minute of inactivity, the display will go dark again.

Turning the Oven Temperature knob will prompt you select a cooking mode with the Mode Select knob.

In the example below, the Mode Select knob has been turned to the True Convection function. The clock time is displayed, as well as the Menu icon on the left. The Oven Temperature knob has been set to 350°F which also displayed.

DISPLAY MENUS

Selecting the Menu button shows a list of menu items and options.

OVEN CONTROLS

(CONTINUED)

SETTING THE CLOCK

1. Activate the display by touching and holding for 2 or more seconds. At first power-up, or after a power failure, the display will flash 00:00. Press the Menu icon.

2. Touch the CLOCK button.

3. Touch the 12 HR or 24 HR button, then touch ENTER to set.

6. Touch the AM or PM, then touch ENTER to set.

7. The clock now displays the correct time.

NOTES:

a. During timed cooking, probe cooking,

and Sabbath mode, the clock time is not displayed.

b. 48” Range has clock on Main Oven display.

only.

4. Touch the UP and DOWN arrows to set the correct hour, then touch HOUR to set.

5. Touch the UP and DOWN arrows to set the correct minutes, then touch MINUTE to set.

OVEN CONTROLS

(CONTINUED)

SETTING THE TIMER

1. Activate the display by touching and

holding for 2 seconds. Touch the Menu

icon.

2. Touch the TIMER button.

3. Touch the UP and DOWN arrows to set the desired amount of hours, then touch HOUR to set.

6. The display will remain on until the time has expired and there is an audible alert. The alert will sound a total of 3 times at 1 minute intervals, or until the user touches the CANCEL button.

7. After the audible alerts, or after the user touches CANCEL, the display will revert back to the default screen.

4. Touch the UP and DOWN arrows to set the desired amount of minutes, then touch MINUTE to set.

5. The timer has been set and displays the amount of time remaining. The timer counts down in 1 minute increments.

NOTES:

a. The timer is not associated with any oven

mode or function.

b. The timer is used solely as a count-down

timer, mainly as an aid to rangetop cooking activity.

c. The timer counts down in one minute

intervals.

d. The maximum timer setting is 23 hour & 59

minutes.

e. The companion oven also has a timer. It

is independent and works the same as the main oven timer.

+ 82 hidden pages

Hestan KRD485GDNG, KRD484GDLPWH, KRD484GDLPGG, KRD485GDNGWH, KRD484GDLPYW User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

MODEL NUMBERS

RATING LABEL

REGULATORY / CODE REQUIREMENTS

GETTING STARTED WITH YOUR APPLIANCE

USING THE RANGETOP

USING THE OVEN

OVEN CONTROLS