HES K20 User Manual

Instruction Manual

HES K20 (13.56 MHz RFID) stand-alone cabinet lock

Package contents Hardware Installation

6-2

5

One (1) HES K20 cabinet lock

1

One (1) Rubber washer

2

One (1) M6 nut

3

One (1) Flat and one (1) Offset Locking Cam

4

Two (2) M4 washers

5

Five (5) Pan Head Phillips Screws

6

M4 x10mm locking cam screw

6-1

M4 x10mm (1-5mm thick door)

6-2

M4 x 20 mm (10-15mm thick door)
M4 x 25 mm (15-20mm thick door)
M4 x 30 mm (20-25mm thick door)

※

Power : 4.5V (AAA 1.5V x 3)

Public Mode (One -time Use)

Lock the door

a

Sol-Do~

b

Unlock the door Unlock the door Lock the door

a

Do-Mi-Sol~

b

User Credentials in Private Mode

a

1

문을 열때

Do-Mi-Sol~

3

2

b

Caution

-Risk of explosion if battery is replaced
by an incorrect type.

-Please only use new alkaline batteries.

LED Feedback

-Red

-Yellow

6-1

5

4

-Amber

Audio Feedback

Short Beep - "Beep-"
Std. Beep - "Sol-Do~"
Long Beep - "Do-Mi-Sol~"

문을 잠글 때

Sol-Do~

a

Flashes
3 times

Close the cabinet door and present a

a

User Credential

-3x flashing Red LED's followed by a
long beep

Rotate the knob to the locked position

b

Present a registered User Credential

a

-3x flashing Yellow LED's followed by an
extended beep

Rotate the knob to the locked position and

b

open the cabinet door

Flashes
3 times

※ Public Mode (One time use)

- Previously registered User Credential will be
erased after unlock and remain open for next user.

Set Up for Public & Private Mode

Step 1 Step 2

Beep

Touch

for 3 s ecs

Flashing
for 3 secs

Present "1st" Master Credential for 3 seconds

a

to set programming mode

-Followed by a short beep

※ -Note: Only the "1st" Master Credential can be
used to set programming mode

b-1

Public m ode

Beep-

Flash

1 time

Public Mo de

b

2x flashing Amber LED's followed by a short beep

Private Mode

3x flashing Amber LED's followed by a long beep

b-2

Private mode

Sol-Do~

Flash

3 times

Flashes
3 times

Present a registered User Credentia

a

-3x flashing Yellow LED's followed by an
extended beep

Rotate the knob to the unlocked position

b

and open the cabinet door

Emergency Power

Step 1 Step 2

a

Do-Mi-Sol~

Sol-Do

b

b

Flashes
5 times

Connect a standard 5 pin Micro USB cable to

a

the USB port on the right side of the lock

When power is applied, both LED's flash 5x

b

followed by an extended beep

Flashes
3 times

Close the cabinet door and rotate the knob

a

to the locked position

-3x flashing Red LED's followed by a long beep

※ Private Mode (Ongoing use)

- Return the handle to the locked position.
The lock will automatically relock after 3 seconds.

c

Present a valid User Credential or Master Credential

c

to unlock the cabinet

-Existing user credentials will be deleted when a valid
Master Credential is used.

-User Credentials will need to be set again during
programming of private mode.

d

Open the door and change all 3 batteries

d

OR

MASTER

USER

Ø13/64"

(5 mm)

Installation Template

5-5/64" (129 mm)

Ø11/16"

(17 mm)

override

CLEAN

override

Registering Credentials

St ep 1 : Mas ter Cr edentials

1

Sol-Do~

Flashing
for 8 secs

a

Present a credential to register as a Master Credential

- Note: The first credential presented will be registered
as a Master Credential

-Flashing Red LED's for 8 seconds followed by a long beep

Present new Master Credential(s)

b

-Up to 20 Master Credentials can be registered

c

Present the same Master Credential 2x to end Master
Credential programming mode

-Flashing Red LED's for 8 seconds

Step 2 : Override Credentials Step 3 : User Credentials

2

Sol-Do~

End of Master Credential programming mode

d

starts Override Credential programming mode

-Flashing Orange LED's for 8 seconds

Present new Override Credential(s)

e

-(Up to 20 Override Credentials can be registered)

Present the same Override Credential 2x to end

f

Override Credential programming mode

※ Note: Skip this step if Override Credentials
need to be deleted or are not required

※ Important Note: Registration of Override Credentials
starts automatically at the end of Master Credential
programming mode

※ Clearly mark 1st Master Credential after initial
programming and keep in a safe place

Flashing
for 8 secs

Beep-

3-1

Present the
Master
Credential

Flashing
for 8 secs

g

g

Present any registered Master Credential

-Flashing Yellow LED's for 8 seconds

Present new User Credential(s)

h

-(Up to 20 User Credentials can be registered)

Note: Skip this step if Override Credentials need

i

to be deleted or are not required

3-2

Public Mod ePrivate Mode

j

Present a User Credential

j

-Red LED blinks 3x followed
by a long beep

Precautions for Override Credentials

※ Override Credentials can be used in Private Mode only
※ Note: Override Credentials are programmed to provide

continuous access while the cabinet is in use.
※ Present the last Master Credential 3x or wait 8 seconds

to end the Master Credential programming mode and
skip programming Override Credentials.

Flashes
3 times

Sol-Do~

Adding/Removing Credentials

Change the Master Credential(s)

Step 1 Step 2 Step 3 Step 4 Step 5

Touch for

8 secs

Flashing
for 8 secs

Pre sent and hold a Mast er
Credential in front of the card
reader f or 8 seconds

-Flashing Yellow LED's

a

Pre sent a Master Cr edential

Public Mode

to delete existing user
credentials

Private Mode

Skip this step

Beep-Beep-Beep-

Beep-Beep-

Flashing
5 times

b

Change the Override Credential(s)

Step 1 Step 2 Step 3 Step 4 Step 5 Step 6

Touch for

Beep-Beep-Beep-

Beep-Beep-

Flashes
5 times

Pre sent a Master

Public Mode

a

Credential to delete existing
user credentials

Private Mode

Skip this step

b

※ FCC statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
※This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.

8 secs

Flashing
for 8 secs

Pre sent and hold a Master
Credential in front of the card
reader f or 8 seconds

-Flashing Yellow LED's

Motor

noise

Motor
noise

Beep-Beep

Beep-

Flashing
for 8 secs

Det ach the Master Car d

c

right af ter three beeps

- Dur ing RED LED blinkin g
for 8 seconds

Beep-Beep

Beep-

Flashing
for 8 secs

Remov e t he Mast er Cr edential

c

from the front of the card reader
aft er he aring 3 shor t be eps

-Wait for flashing Red LED's for 8
seconds bef ore mo ving to nex t step

Sol-Do~

Flashing
for 8 secs

Remov e t he Mast er Cr edential

d

from the front of the card reader
aft er he aring 3 shor t be eps

-Flashing Red LED's f or 8 sec onds

(Up to 20 Master Cards can be registered)

Beep~

Flashes
for 8 secs

Flashing Amber LED's for 8

e

second s af ter shor t b eep

Beep-

Pre sent the las t M aster Cr edential 2 x

e

to end Mast er C redenti al progr amming

mode

New Master Cre dential(s) success fully

f

registered

Sol-Do~

Present Override Credentials to

f

the front of the card reader to

register

Ov erride Credent ial
pro gr amming mode

※ Regis tering Overr ide Creden tials can
only begin after completing Master
Cr eden tial p ro gr amming

Pre sent t he last Overr ide Cre dential

g

2x to end O verride Credent ial
pro gr amming mode

New Overr ide Cre dential(s) succ essf ully

h

registered

Beep-

ELECTRONIC SECURITRY HARDWARE

HES | Securitron
assaabloyesh.com | 800.626.7590 | 10027 S. 51st Street Phoenix, AZ 85044 USA

Document #3080006.014 Rev. 1