HES 7000-12-24, 7000-LBM, 7000C-630, 7000C-630-LBM, 783S-613E Installation Instructions

...

Cutout Templates (continued)

7000 Series Electric Strike

NOTE 1: For use with RIM exit devices in metal jambs with up to a 3/4” pullman

8-1/4”

[209.55]

latch.

3-3/8”

NOTE 2: Compatible with

[85.72]

American Device, Arrow, Dor-O-Matic, Monarch, Precision, Sargent. Von Duprin, and Yale.

NOTE 1: For use with RIM exit devices in aluminum jambs and surface mounted vertical rod exit devices with up to a 3/4” pullman latch. Includes keeper socket adapter.

5-3/4”

[146.05]

3-3/8”

[85.72]

NOTE 2: Compatible with American Device, Arrow, Dor-O-Matic, Jackson, Monarch, Precision, Sargent, Von Duprin, and Yale.

8-1/4”

NOTE 1: For use with RIM

[209.55]

exit devices in aluminum jambs with up to a 3/4” pullman latch. Includes keeper pocket

3-3/8”

[85.72]

adapter.

NOTE 2: Compatible with American Device, Arrow, Dor-O-Matic, jackson, Monarch, Precision, Sargent. Von Duprin, and Yale.

1-13/32”

[35.71]

HES, Inc.

3021006.002, Revision 3

Phoenix, AZ 85044 800-626-7590 www.hesinnovations.com

11/16”

[17.46]

1-13/32”

[35.72]

11/16”

[17.46]

1-13/32”

[35.72]

25/32”

[19.72]

23/32”

[18.24]

3/8”

[9.52]

3/8”

[9.52]

783S OPTION

1-17/32”

[38.89]

786S OPTION

1-17/32”

[38.89]

789S OPTION

1-3/4”

[44.45]

1-11/16”

[42.86]

[209.55]

9-1/8”

[231.78]

Copyright © 2017, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Hanchett Entry Systems, Inc. is prohibited.

8-1/4”

1-3/4”

[44.45]

8-1/4”

[209.55]

1-3/4” [44.5]

5-3/4”

[146.05]

9”

[228.60]

9”

[228.60]

[165.10]

1/2”

[12.70]

6-1/2”

1-11/16”

[42.85]

3-3/8” [85.72]

Inches [mm]

11/16”

[17.45]

[12.70]

1-11/16”

[42.85]

3-3/8”

[85.72]

1-11/16”

[42.85]

3-3/8”

[85.72]

1/2”

(Model 7000-106)

Installation Instructions

Product Components

7000 Series Electric Strike Body

From Electric Strike

Specifications

ELECTRICAL RATINGS (Solenoid)

VOLTAGE

CONTINUOUS DUTY

INTERMITTENT DUTY*

7000 Series: For Indoor Use Only

Solenoids are rated at +/- 10% indicated value. * Applies to AC Only: 10% max duty cycle (2 min. max on time)

12 VDC 24 VAC

0.24A

24 VDC

0.12A

- -

Ratings

791/792 783S/786S/789S

Static Strength: 1,500 lbs 1000 lbs Dynamic Impact: 70 ft-lbs 50 ft-lbs Endurance: 500,000 cycles 500,000 cycles

ASSA ABLOY, the global leader in door opening solutions

12-Volt and 24-Volt Pigtail Connectors

12–16 VAC

- -

0.24–0.32A

Pigtail Connectors

MINIMUM WIRE GAUGE REQUIREMENTS

200 feet or less

0.12A

200 - 300 feet

300 - 400 feet

From Power Source

VOLTAGE

12 VDC 24 VDC

18 gauge

16 gauge

14 gauge

20 gauge

18 gauge

16 gauge

UL294 Performance Levels

Destructive Attack: Level 1 (No attack test) Line Security: Level I (No Line Security) Endurance: Level IV (100,000 cycles) Standby Power: Level I (No secondary power source)

Installation

Installation (continued)

NOTE 1: Before electrically connecting the device, the input voltage must be verified using a multimeter. Many power supplies and low voltage transformers operate at higher levels than listed. Any input voltage exceeding 10% of the electrical specification (See Page 1) may cause severe damage to the unit and will void the warranty.

NOTE 2: Installation wiring for the product and wiring methods shall be in accordance with the National Electrical Code, ANSI/NFPA 70.

Preparing the Frame

1. PREPARE door jamb per the appropriate template detail (see pages 3–4).

Finishing the Installation

NOTE: For 12 VDC, the Plug In Connector (pigtail)

marked “12 VDC” should be used; for 24 VDC, the pigtail marked “24 VDC” should be used.

1. CONNECT power to the electric strike, and INSTALL into jamb using the hardware provided with the option kit.

Fail Secure Mode

Cotter Pin

“D” Washer

Fail Safe Mode

Converting the Operation Mode

NOTE: The suitability of the locks in the FAIL SECURE

OPERATION mode is up to the local Authority Having Jurisdiction (AHJ) and emergency exit hardware may be required in such installations.

“D” Washer

Solenoid Slot

Adjusting the Horizontal in the 791 and 792 Options

1. LOOSEN the screws (a), but DO NOT REMOVE.

2. SHIFT the electric strike to the proper horizontal position and TIGHTEN the screws (a).

Cutout Templates

NOTE: For use with Cylindrical locksets up to 5/8” throw.

1-1/4”

[31.75]

791 Option

1-1/4”

[31.75]

1-5/8”

[41.28]

Inches [mm]

1-3/16” [30.48]

1. Because the electric strike ships in fail secure mode, COMPLETE the following steps to convert to fail safe mode.

a. REMOVE the cotter pin from the solenoid linkage.

Solenoid Slot

b. REMOVE the solenoid mounting screw and washers.

c. REMOVE the solenoid from the keeper module.

d. TURN the solenoid upside down, and RE-INSERT it into the keeper module.

e. RE-INSTALL the mounting screw and washers at the opposite end of the keeper module, and ENSURE the “D” washer is positioned firmly into the solenoid slot.

White (Common) Orange (Normally Open) Green (Normally Closed)

f. REPLACE the cotter pin to secure the solenoid linkage.

Figure 1. Converting the Operation Mode

Figure 2: LBM Wiring

NOTE: For use with Cylindrical locksets up to 5/8” throw.

7-15/16” [201.61]

1-3/16” [30.18]

4-7/8”

[123.82]

5/32”

[3.96]

3-3/8”

[85.72]

4-7/8”

[123.82]

4-1/8”

[104.78]

4-7/8”

4-1/8”

[104.78]

5/32”

[4.02]

1-19/32”

[40.52]

3-3/8”

[85.72]

792 Option

1-7/16” [36.51]

3-3/8”

[85.72]

1/4”

[6.35]

[44.45]

1-3/4”

[31.75]

7-15/16” [201.63]

[188.95]

1-7/16”

7-7/16”

1-5/8”

[41.28]

1-3/16” [30.48]

3-3/8”

[85.72]

1-7/32” [30.96]

5/32”

[4.02]

1-19/32”

[40.52]