HES 1500, 1600 Installation Instructions Manual

1500 Series and 1600 Series Electric Strikes

Installation Instructions

NOTE: Installation wiring for the product and wiring methods shall be in accordance with the National Electrical
Code, ANSI/NFPA 70.

Product Components

1

1500 Series or 1600 Series Electric Strike

2

Trim Enhancer

1

3

Pigtails (12 VDC and 24 VDC)

4

5/64” Hex Wrench

5

#6-32 x 3/16” Phillips Head
Screws to Mount Trim Enhancer

1

Specications

ELECTRICAL RATINGS FOR
1500/1600 (Solenoid)

VOLTAGE

CONTINUOUS DUTY

INTERMITTENT DUTY*

ELECTRICAL RATINGS FOR
1500E/1600E (EcoStrike™)

VOLTAGE

IN RUSH CURRENT

CONTINUOUS DUTY

Solenoids are rated at +/- 10% indicated value.
* Applies to AC Only: 10% max duty cycle
(2 min. max on time)

12 VDC 24 VAC

0.24A

24 VDC

0.12A

- -

Input voltage: 10–30 VDC, Autosensing

Minimum Activation Duration: 1 second

10 VDC 30 VDC

0.475A

0.010A

12 VDC

0.460A

0.009A

12–16 VAC

- -

0.24–0.32A

24 VDC

0.220A

0.005A

0.12A

0.215A

0.004A

2

4

MINIMUM WIRE GAUGE REQUIREMENTS

200 feet or less

200 - 300 feet

300 - 400 feet

NOTE: The above table applies to Models 1500, 1500E, 1600, and 1600E.

3

5

VOLTAGE

12VDC 24VDC

18 gauge

16 gauge

14 gauge

20 gauge

18 gauge

16 gauge

Models 1500E and 1600E: For Indoor Use Only
Models 1500 and 1600: For Outdoor Use

Ratings

Static Strength: 1,500 lbs
Dynamic Impact: 70 ft-lbs
Endurance: 250,000 cycles

ASSA ABLOY, the global leader
in door opening solutions

UL294 Performance Levels

Destructive Attack: Level 1 (No attack test)
Line Security: Level I (No Line Security)
Endurance: Level IV (100,000 cycles)
Standby Power: Level I (No secondary power source)

3086006.001 Rev 3

Converting the Operation Mode

IMPORTANT NOTE: Converting the electric strike to FAIL SAFE mode negates the unit’s re rating.

NOTE 1: The 1500 and 1600 Series Electric Strikes ship congured for FAIL SECURE OPERATION. The steps

below are provided to convert to FAIL SAFE OPERATION, if desired. The operation mode of the
1500E and 1600E (EcoStrike ™ ) is set at the factory and cannot be changed.

NOTE 2: The suitability of the locks in the FAIL SECURE OPERATION mode is up to the local Authority Having
Jurisdiction (AHJ) and emergency exit hardware may be required in such installations.

2

Connecting the Power

IMPORTANT NOTE: Before electrically connecting the device, the input voltage must be veried using a multimeter.

Many power supplies and low voltage transformers operate at higher levels than listed. Any input
voltage exceeding 10% of the electrical specication (see Page 1) may cause severe damage to the
unit and will void the warranty.

1500 or 1600:

1500E or 1600E:

NOTE: No AC input voltage.

For 12 VAC, 12 VDC, or 16 VAC, USE the pigtail marked “12 VDC.”
For 24 VAC or 24 VDC, USE the pigtail marked “24 VDC.”

For 10–30 VDC, ALWAYS USE the pigtail marked “12 VDC.”

Purple and Black Wires

Red and Black Wires

White

Tan

Common

Door Closed and Latched

Tan
White

IF CONNECTOR IS MISSING

CONNECT

RED

VIOLET

STRIKE

BLACK

ELECTRIC

RED/GREEN

VIOLET

STRIKE

ELECTRIC

BLACK

RED/GREEN

RED

TOGETHER

(+ 12 VDC)

(-NEG)

CONNECT
TOGETHER

(+ 24 VDC)

CONNECT
TOGETHER

(-NEG)

3086006.001 Rev 3

Preparing the Frame

3

MORTISE LOCKSETS

Please note the horizontal centerline of the electric strike in relation to
the centerline of the mortise lockset.

C

L

Mortise
Lockset

Vertical

Centerline

C

L

Strike

4"

[101.6 mm]

8"

[203.2 mm]

C

L

*

3/8"

[9.53 mm]

Lock

1-1/4"

[31.8 mm]

1-3/4"

[44.45 mm]

* Can be Mortise lock and option specic. See gures below if

using a Schlage L9000 or Yale 8700 series.

1-1/4"

[31.8 mm]

Strike

Prep

3-1/2"

[88.9 mm] [104.77 mm]

5/8"

[15.88 mm]

Inches [mm]

4-1/8"

4-7/8"

[123.83 mm]

CYLINDRICAL LOCKSETS

Please note the horizontal centerline of the electric strike in relation to
the centerline of the cylindrical lockset.

C

L

Cylindrical

Lock

Vertical

Centerline

C

L

Strike

Prep

STRIKE

2-1/4"

[57.15 mm]

C

L

3-1/2"

[88.9 mm]

LOCK

1-1/4"

[31.8 mm]

1-3/4"

[44.45 mm]

5/8"

[15.88 mm]

1-1/4"

[31.8 mm]

Inches [mm]

4-7/8"

[123.83 mm]

4-1/8"

[104.77 mm]

See Note 2

*

METAL JAMB DIMENSIONS FOR FACEPLATES

Please see Notes 2 & 3 for dimensions when using Lip Extensions

Normally Used With Mortise Locks Without Deadbolt
NOTE1: Cannot be used with Schlage L9000 or Yale 8700 series.

NOTE2: Add 1/4” [6 mm] to this dimension when using a lip extension.

*

NOTE3: Add 3/8” [9.5 mm] to this dimension when using a lip extension. NOTE3: Add 3/8” [9.5 mm] to this dimension when using a lip extension.

**

Cutout dimenstions for option faceplates (metal jamb): 1J, 1KM, 1NM

Inches [mm]

4-7/8"

[123.83 mm]

4-1/8"

3-3/8"

[104.77 mm]

[85.72 mm]

See Note 2

*

2 X 12-24

1-1/4"

[31.8 mm]

UNC THREADS

Normally Used With Mortise Locks With Deadbolt
NOTE1: Can be used with Schlage L9000 or Yale 8700 series.

NOTE2: Add 1/4” [6 mm] to this dimension when using a lip extension.

*

**

Cutout dimenstions for option faceplates (metal jamb): 1KD, 1ND, 1NTD

29/32”

[23.01 mm]

3-3/8"

[85.72 mm]

19/32”

[15.08 mm]

C

L

C

L

5/32”

1

-1/4"

[31.8 mm]

4-1/8"

[104.77 mm]

2 X 12-24

UNC THREADS

Inches [mm]

4-7/8"

[123.83 mm]

1500 – 1-1/8” [28.58 mm]
1600 – 1-3/8” [34.93 mm]

**

See Note 3

}

1500 – 1-1/8” [28.58 mm]
1600 – 1-3/8” [34.93 mm]

3086006.001 Rev 3

See Note 3

**

}

Selecting the Appropriate Faceplate Option

OPTION

DESCRIPTION

1500

1600

For Use With: Cylindrical locksets with up to ¾” throw and all locksets with center-lined bolts.

For Use With: Mortise locksets with up to ¾” throw latchbolt.

For Use With: Mortise locksets with up to ¾” throw latchbolt.
For Use With: Mortise locksets with up to ¾” throw latchbolt.

For Use With: Mortise locksets with deadbolt for night latch function only.

For Use With: Mortise locksets with deadbolt for night latch function only.
For Use With: Mortise locksets with deadbolt for night latch function only.

For Use With: Mortise locksets with a normally extended 1” deadbolt and center-lined deadlatch.

(4-7/8” x 1-1/4” Square Corner)

Frame prep

C

= center line (2nd Line = centerline of faceplate opening)

L

4

Inches [mm]

1J

1N

1K

1NM

1ND

1KM

1KD

1NTD

1J

1K

1KM

1KD

1N

1NM

1ND

1NTD

Compatible With: All brands of cylindrical latchbolts

Compatible With: Baldwin, Marks, PDQ

Compatible With: Accurate, Arrow, Best, Corbin Russwin, Falcon, Sargent (7800, 8200, and 9200),

Yale (8800)

Compatible With: Dorma (9500), Jackson, Sargent (7700 and 8100), Schlage, Yale (8700)

Compatible With: Accurate, Baldwin, Marks, Omnia, PDQ, Schlage

Compatible With: Accurate, Arrow, Baldwin, Best, Corbin Russwin, Falcon (45H, 47H, 34H, and

37H), Marks, PDQ, Sargent (7800, 8200, and 9200), Yale (8800)

Compatible With: Sargent (7700 and 8100), Schlage, Yale (8700)

Compatible With: Accurate, Arrow, Baldwin, Marks, Omnia, PDQ, Schlage

3086006.001 Rev 3

X X

X X

X X

X X

X

X

X

X

Adjusting the Shim

NOTE: To adjust the shim height, it is necessary to power the electric strike to open keeper.

STEP 1

LOOSEN the locking screw with the
5/64” Hex Wrench.

STEP 2

ADJUST the shim height to the desired level
by turning the upper and lower set screws
(clockwise to raise and counterclockwise
to lower).

5

STEP 3

TIGHTEN the locking screw to lock position.

3086006.001 Rev 3

6

HES, Inc.

Phoenix, AZ

800-626-7590

www.hesinnovations.com

Copyright © 2018, Hanchett Entry Systems, Inc., an ASSA
ABLOY Group company. All rights reserved. Reproduction in
whole or in part without the express written permission of
Hanchett Entry Systems, Inc. is prohibited.

3086006.001 rev 3